• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.51-58
• /
• 1998

This paper considers analysis of the lubrication between the piston ring and the cylinder liner. Piston ring lubrication analysis considering oil transport is important because oil consumption is an essential factor to design the piston assembly. To develop the lubrication analysis program for the piston ring, oil continuity condition and open-end boundary assumption are used for computational boundaries. Results show that oil continuity can be almost satisfied at any crank angle in and out of the piston ring clearance. Therefore the amount of oil consumption and the dynamic behavior of ring pack can be estimated using this algorithm. And it can be known that the effective width may be smaller than the full width of the piston ring, so oil starvation condition should be considered for the lubrication analysis of the piston ring.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.928-934
• /
• 2000

This paper describes a method developed for the simulation of ring pack lubrication characteristic in an internal combustion engine. In general, the quantity of oil supply for piston ring lubrication may be insufficient in filling the entire volume formed at the interference between the piston ring and the cylinder liner. Thus the oil starvation condition should be considered in analyzing piston ring lubrication. In order to reasonably estimate the amount of oil left over on the cylinder liner, the flow rate at the posterior portion of the interface should be calculated with an adequate boundary condition that confirms flow continuity condition. In this analysis, oil starvation and open-end boundary conditions are considered at the inlet and outlet of the piston rings. The lubrication characteristic of each piston ring is obtained by an iterative method with sequential steps. It is revealed that piston rings are operated under oil starvation in most operating cycles and the result under these conditions are quite different from that with the fully-flooded assumption.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.358-364
• /
• 1998

Lubricational characteristics at the interface between the piston ring and the cylinder liner are considered in this paper. To verify that surface shape and operating conditions of the engine can affect the state of lubrication, the changes of the minimum film thickness and friction force are calculated with various conditions. Oil starvation and open-end boundary condition are used to determine computational boundaries as reported on previous paper for lubrication analysis for the piston ring. From this analysis, it can be found that lubricational characteristics are seriously affected by degree of oil starvation, surface shape and operating conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1187-1190
• /
• 2004

In this paper we analyze the reflection characteristics of a dielectric microstrip line with an open-end termination containing optically induced plasma region, which are analyzed by the assumption that the plasma is distributed homogeneously in the laser illumination. The characteristics impedances resulting from the presence of plasma are evaluated the transmission line model. To estimate theoretically the characteristic response of same systems in the time domain, the Fourier transformation method is evaluated. The reflection characteristics of time response in microwave systems have been calculated.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.232-239
• /
• 1999

Generally quantity of supply oil for piston ring lubrication in an internal combustion engine may be insufficient to fill the entire volume formed in the clearance between piston ring and cylinder liner. Thus oil starvation condition should be considered for the analysis of piston ring lubrication. In order to reasonably estimate amount of oil left on the cylinder liner, adequate boundary condition should be adapted for the analysis of ring pack lubrication. In this analysis of ring pack lubrication of an internal combustion engine, oil starvation and open-end boundary conditions are considered at inlet and outlet of piston rings. It is revealed that piston rings are operated under oil starvation in most operating cycle and the result with these conditions are quite different from that with fully-flooded assumption.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.233-239
• /
• 1999

Generally quantity of supply oil for piston ring lubrication in an internal combustion engine may be insufficient to fill the entire volume formed in the clearance between piston ring and cylinder liner. Thus oil starvation condition should be considered for the analysis of piston ring lubrication. In order to reasonably estimate amount of oil left on the cylinder liner, adequate boundary condition should be adapted for the analysis of ring pack lubrication. In this analysis of ring pack lubrication of an internal combustion engine, oil starvation and open-end boundary conditions are considered at inlet and outlet of piston rings. It is revealed that piston rings are operated under oil starvation in most operating cycle and the result with these conditions are quite different from that with fully-flooded assumption.

• 현장농수산연구지
• /
• 제4권1호
• /
• pp.128-137
• /
• 2002

개발된 알루히트를 이용하여 지하수 이용 열교환기를 개발하였다. 시작기는 600mm, 700mm 알루히트 19개의 끝을 U자 용접을 하여 지하수가 직렬흐름이 되도록 2가지로 제작하였다. 성능시험은 개방된 공간에서 지하수 유량과 공기양의 변화를 주면서 상온에서 실시하였다. 1. 시작기의 열전달 계수는 33~156(W/m²℃) 범위로 나타나 설계가정 값에 잘 일치하는 것으로 판단되었다. 2. 열전달 면적이 증가할수록, 지하수 입·출구의 온도 차이가 클수록, 공기의 입·출구 온도 차이가 클수록, 또 송풍량이 증가할수록 에너지 전달량이 증가하였다. 3. 지하수 입·출구 온도 차이가 6℃ 이고 송풍량이 6,000m³/h일 때 전달 열용량은 6,825W였으며, 공기의 입·출구 온도 차이는 25.8℃에서 23.2℃로 -2.6℃의 강화 효과가 있었고, 대류열전달계수는 88.5W/m²℃ 였다. 4. 지하수 입·출구 온도 차이가 2℃ 이고 송풍량이 4,000m³/h일 때 전달 열용량은 2,625W으로 작았지만, 공기의 입·출구 온도 차이는 27℃에서 22.5℃로 -4.5℃의 강화 효과가 있었고, 대류열전달계수는 33.6W/m²℃였다. 5. 시작기 I, II, III의 전달 열용량 데이터 각각의 상관계수 R²은 0.9141, 0.8935, 0.9393이었으며, 공기유량이 6,000m³/h, 5,000m³/h, 4,000m³/h일 때 각각의 데이터 상관계수 R²은 0.9513, 0.9414, 0.9003으로 신뢰할 수 있었다.