• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.2
• /
• pp.164-171
• /
• 2004

Active control techniques have been used in wide areas of noise and nitration control engineering and a noise barrier is one of them. Omoto's work in 1993 would be one of the fundamental and systematic studies on the actively controlled noise barrier, in which he used equal number of control sources and error sensors. The error sensors were placed uniformly along the top edge of the noise barrier with equal distance apart and the control sources were placed in the exactly same way some distance apart from the error sensors. Since then, a couple of studies were made on the secondary sources'arrangement rather than the optimality of secondary source positions. Shao's results showed that arc shaped arrangement for secondary sources is better than the straight line one, and later work of Yang showed that the more important factor is the average distance between the primary source and secondary sources. However, since these studies were all executed with a simple uniform distribution of the secondary sources along the straight line or arc, it is difficult to conclude which arrangement is superior In order for the fare comparison. the optimality of the source positions in each arrangement must be given in prior. The primary goal of this study is focused on this aspect and some major factors were investigated and compared. The computer simulation results showed that the arc shaped arrangement is marginally better than the straight line one, and more importantly slightly tuned position can greatly improve the performance of the control system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.98-106
• /
• 2007

This paper represent improved on-line turn off angle control schemes for switched reluctance motors based on current control. For the purpose of finding the optimal commutation switching angle point with improved controller, it is utilized turn on and turn off position calculation with inductance vs. current vs. not linkage analysis method. The goal of proposed paper is the maximization of the energy conversion per stroke and torque ripple reduction and obtaining approximately flat-topped current waveform. The proposed control scheme is demonstrated simulation and on a prototype experimental system.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.73-80
• /
• 1993

There and two important variables in machining process control, which are feed and cutting speed. It is possible to improve the machining accuracy and the productivity by maintaining the optimal feed and cutting speed. In this work, a controller is designed to achieve on-line cutting force control based on the modeling of cutting process dynamics established through step response test. Two schemes are proposed and implemented. The first is feed control under the constant spindle speed and the second is spindle speed control under the constant feed. Finally, both are proved to work properly through simulation and experimentation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1136-1139
• /
• 1996

For on-line trajectory planning such as teleoperation it is desirable to keep good manipulability of the robot manipulators since the motion command is not given in advance. To keep good manipulability means the capability of moving any arbitrary directions of task space. An optimization process with different manipulability measures are performed and compared for a redundant robot system moving in 2-dimensional task space, and gives results that the conventional manipulability ellipsoid based on the Jacobian matrix is not good choice as far as the optimal direction of motion is concerned.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.570-571
• /
• 2008

This paper presents a method for the determination of total transfer capability in interconnected power systems, which is based on sequential quadratic programming (SQP). The objective function is the maximization of the interconnected line flow. To calculate TTC the control variables are the active power of the generating units, the voltage magnitude of the generator, transformer tap settings and SVC setting. The state variables are the bus voltage magnitude, the reactive power of the generating unit, line flows and the tie line flow. The method proposed is applied to the modified IEEE 14 buses model system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.5
• /
• pp.470-477
• /
• 1990

Singh's multi-level method is extended to the optimal tracking control of a large interconnected dynamical system which has coupled states and coupled inputs. The steady-state tracking error and a convergence condition for the extended multi-level method are derived analytically and the results show that the steady-state tracking error and a convergence rate have to be compromised. Also, a new multi-level method which is advantageous over the Singh's method in steady-state tracking error and computational burden is proposed by introducing nominal inputs into the performance index. The resulting feedback gain matrix and the compensation vector are optimal for all initial conditions so that eventual on-line computation is minimal.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.338-341
• /
• 1997

The current consumption and the heat produced in the printhead of thermal printer are mainly governed by total printing dots and printing time for each line. Simple algorithm is proposed to optimize the performance of a thermal printhead, which use variable division according to bit-mapped data of its 1 line. And, for protecting the thermal printhead from exceeding heat, I control the heat energy of each microheater(dots) on the thermal printhead through changes in the applied pulse width.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.3
• /
• pp.288-292
• /
• 2010

Recently, in energy storage system, the EDLC is paid attention as a new environmentally friendly energy storage element. This capacitor has higher energy density than the electrolytic capacitor. Also, this capacitor has a lot of advantage such as no maintenance, longer life cycle and faster charge-discharge time than the battery system. But the EDLC must have a each charge-discharge controller to effectively control, an energy design method circuit to use effectively energy, and several compensation techniques to control a optimal operating. In this respect, this study suggests major parameters to effectively represent the characteristics of EDLC, the measurement methods of those parameters have been investigated with experiments, and the interpretation about the buck/boost DC/DC converter for the operation of EDLC.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.105-109
• /
• 2001

This paper discuss the real-time self-tuning learning control based on evolutionary computation, which proves its the superiority in the finding of the optimal solution at the off-line learning method. The individuals are reduced in order to learn the evolutionary strategy in real-time, and new method that guarantee the convergence of evolutionary mutations are proposed. It possible to control the control object varied as time changes. As the state value of the control object is generated, applied evolutionary strategy each sampling time because the learning process of an estimation, selection, mutation in real-time. These algorithms can be applied, the people who do not have knowledge about the technical tuning of dynamic systems could design the controller or problems in which the characteristics of the system dynamics are slightly varied as time changes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.9
• /
• pp.1463-1468
• /
• 2003

This paper presented the real-time self-tuning learning control based on evolutionary computation, which proves its superiority in finding of the optimal solution at the off-line learning method. The individuals of the populations are reduced in order to learn the evolutionary strategy in real-time, and new method that guarantee the convergence of evolutionary mutations is proposed. It is possible to control the control object slightly varied as time changes. As the state value of the control object is generated, evolutionary strategy is applied each sampling time because the learning process of an estimation, selection, mutation is done in real-time. These algorithms can be applied; the people who do not have knowledge about the technical tuning of dynamic systems could design the controller or problems in which the characteristics of the system dynamics are slightly varied as time changes.