• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.223-228
• /
• 2012

The low-temperature pyrolysis of ABS, polyethylene (PE) and an ABS-polyethylene (ABS-PE) mixture was conducted in a batch reactor at $450^{\circ}C$. The conversion and the product yield were measured as a function of the reaction time with a variation of the mixture composition. The oil products formed during pyrolysis were classified into gas, gasoline, kerosene, gas oil and heavy oil according to the petroleum product quality standard of the Ministry of Knowledge Economy. The pyrolysis conversion increases with an increase in the content of PE. The yield of the pyrolytic products was ranked as heavy oil>gas>gasoline>gas oil>kerosene as the content of PE in the mixture increases.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.1
• /
• pp.140-150
• /
• 1996

CFC-12, which has been used most widely in automobile air conditioners and household refrigerators is scheduled to be phased out soon because of its high ozone depletion potential. Now HFC-134a is suggested as an alternative refrigerant for CFC-12. In this Study, we intended to investigate how PAG oil influence evaporation heat transfer and flow pattern, using R-134a and PAG oil influences evaporation heat transfer and flow pattern, using R-134a and PAG oil in the horizontal miro-fin evaporation tube. Experiments were conducted under the flowing est conditions : mass velocity 86-250kg/$m^2$s, heat flux 5-30 ㎾/$m^2$, oil concentration 0-21 wt.% and saturation temperature 5$^{\circ}C$. Local evaporation heat transfer coefficients were found to be higher at the top, side and bottom of the tube in this order. Average heat transfer coefficients turned out to increase with oil concentration increment up to 3 wt.% oil concentration, whereas heat transfer coefficients gradually decreased over 3 wt.% oil concentration, because of oil-rich liquid film was formed on the heat transfer surface. Flow patterns were rapidly transitioned to annular regimes up to 3 wt.% oil concentration. In case of pure refrigerant, measured heat transfer coefficients in the experiments were similar to those of Kandlikar＇s correlation.

• The Korean Journal of Food And Nutrition
• /
• v.36 no.6
• /
• pp.479-488
• /
• 2023

In this study, quality properties of rapeseed oil by different roasting temperatures (140, 160, 180, and 200℃) were investigated. Roasted-pressed oil (RPO) showed a decrease in lightness and an increase in redness and yellowness with an increase in temperature compared to cold-pressed oil (CPO). In addition, the β-carotene and tocopherol content also increased in RPO as the roasting temperature increased. The tocopherol content increased by 18~20% in RPO at 200℃ compared to CPO. This increase in bioactive components led to improved radical scavenging activity dependent on roasting temperature, and RPO at 200℃ showed a 2.7-fold improvement compared to CPO. Finally, it was observed that higher roasting temperatures resulted in an extended oxidation induction period, increasing by up to 3.3 times. In conclusion, roasting is an effective method for enhancing the oil functionality of domestic rapeseed varieties. This study provides basic data for producing high-quality oil.

• Journal of Korean Society of Forest Science
• /
• v.5 no.1
• /
• pp.16-21
• /
• 1966

This experiment was accomplished to study the effect affecting to the absorption of creosote solutions by treating temperatures 20, 50 and $80^{\circ}C$ when the small test pieces were treated as short timed immersion process. The test speciemens used in this experiment were cut into 180 pieces of $2.5{\times}2.5{\times}5cm$ size from the air dried sapwood of Righda Pine (Pinus rigida M.). They were controlled to about 8 to 9% moisture contents and measured specific gravities. Four creosote solutions of $S_1$(straight creosote), $S_2$(creosote 70% : heavy oil 30%), $S_3$(creosote 50% : heavy oil 50%) and $S_4$(creosote 30% : heavy oil 70%), and three treating temperatures of $T_1$($20^{\circ}C$), $T_2$($50^{\circ}C$) and $T_3$($80^{\circ}C$) were applied by factorial split plot design in the each treatment of 3, 7, 15, 30 and 60 minutes immersion. According to the results this study may be concluded briefly as follows : 1. In this immersion process the absorption effects of creosote mixtures by the increase of temperatures are recognized considerably in the each treating times. However in the straight creosote of treated solutions the effective differences were not shown but most effective differences were shown in the $S_2$ solution. 2. Although the solutional absorptions were raised considerably by temperature increase in every treating times the absorption effects of creosote mixtures were not reached to that of straight creosote because the effects are considerably lowered if the treating solutions were mixed with heavy oil even a small quantities. 3. The relations between the creosote contents of treating solutions and the absorptions in wood are shown as Fig. 1, 2, 3, 4 and 5. In these figures the absorption curves made by higher temperature treatment $T_3$ are on the lower treatments $T_1$ and $T_2$ if the solutions were mixed with heavy oil. 4. This report is a part of the consolidated results announced at the annual meetings of Korean Forestry Association in 1964 and 1965.

• KSBB Journal
• /
• v.26 no.5
• /
• pp.453-458
• /
• 2011

In this study, two different extraction techniques, organic solvent extraction and supercritical carbon dioxide ($SCCO_2$) extraction, were employed to evaluate the extraction efficiency of oil from Chlorella vulgaris. In the organic solvent extraction, the effects of various organic solvent on the extraction yield were investigated. The $SCCO_2$ extraction was carried out while varying such operating parameters as temperature, pressure, $SCCO_2$ flow rate, and cosolvent. About 4.9 wt% of oil was extracted from ground Chrollera vulgaris for 18 h when dichloromethane/methanol (2：1, v/v) was used as an extraction solvent. The oil yield of the $SCCO_2$ extraction was found to be very low (0.53 wt%) and to increase up to about 0.86 wt% with the addition of cosolvent.

• KSBB Journal
• /
• v.25 no.4
• /
• pp.379-386
• /
• 2010

In the present study, biocompatible poly (ethylene glycol) (PEG) microparticles containing coriander essential oil were prepared using a supercritical particles from gas saturated solution (PGSS) process to improve the stability of the coriander oil. The effects of various process parameters such as temperature, pressure, and nozzle diameter on the morphology and entrapment efficiency of coriander oil loaded PEG microparticles were then investigated. A positive influence on the formation of spherical microparticles was observed with increasing temperature and decreasing pressure. Furthermore, somewhat more porous microparticles were produced with an increase in pressure. At a given temperature, the highest entrapment efficiency of coriander essential oil in PEG microparticles was observed under the lowest experimental pressure condition.

• Korean Journal of Food Science and Technology
• /
• v.38 no.1
• /
• pp.16-21
• /
• 2006

Effect of heat (160, 190, and $220^{\circ}C$ for 24 hr) on coconut oil was examined by principal component analysis using electronic nose consisting of six metal oxide sensors. Increase in heating temperature decreased ratio of resistance and first principal component score (from +0.952 to -0.325), indicating rancidity of coconut oil increased at high heating temperature. Result of electronic nose based on GC with surface acoustic wave sensor showed significant changes in volatile profiles of coconut oil. High resolution olfactory imaging $(VaporPrint^{TM})$ was particularly useful for evaluating oil quality. Peak numbers and areas increased with increasing heating time and temperature (160, $220^{\circ}C$). Electronic nose analysis can provide simple, fast, and straightforward results and is best suited for quality control and process monitoring in flavor field of food industry.

• Proceedings of the KIEE Conference
• /
• 2005.07a
• /
• pp.721-723
• /
• 2005

This paper analyses the characteristic of temperature and energy of oil field cable in transient state such as lightning surge. For analysis in various conditions, many actual underground power cable systems are modeled using ATP These results are applied for the examination of temperature increase when the hitting of lightning surge are occurred. The inner part temperature of OF cable is analysed according to the various kinds of cable using the thermal model of transient state. The temperature increase of sheath and crossbonded lead by fault current is also analysed using IEC 60949.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.10
• /
• pp.487-495
• /
• 2005

This paper reviews the characteristic of thermal and temperature of oil field cable in transient state such as grounding fault and lightning surge. For analysis in various conditions, many actual underground power cable systems are modeled using ATP. These results are applied for the examination of temperature increase when the single line to ground fault by the breakdown of insulation part and hitting of lightning surge are occurred. The inner part temperature of OF cable is analysed according to the various kinds of cable using the thermal model of transient state. The temperature increase of sheath and crossbonded lead bv fault current is also analysed using IEC 60949.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.57-62
• /
• 1993

To increase the fuel economy, a reduction of friction loss is important in engines. Experimental investigations have been required for reducing the friction loss of crankshaft bearings. Hydraulic cylinder, and servo control ler system which modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated. Experiment is performed. Friction torque, journal locus and circumferential temperature variations of crankshaft bearings were measured with appling load, revolution speed, and oil inlet temperature, etc.