• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.6
• /
• pp.462-469
• /
• 2014

After drilling operations at the offshore plant, crude oil is producted under high pressure. After that time, oil recovery is reduced, because the pressure of the pipe inside is low during the secondary produce. At that time injection sea water at the pipe inside through water injection pump that the device increase to recovery. A variety of mathematical analysis during the detailed design analysis was not made through the dynamics characteristic at the domestic company. 2D model has reliability of analysis results for the uncomplicated model. Also element and the node the number of significantly less than in the 3D model. So, the temporal part is very effective. In addition, depending on the quality of mesh 3D is a real model and FEM model occurs error. So, user needs a lot of skill. In this paper, a 2D finite element analysis was performed through the dynamics analysis and the study model was validated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.2
• /
• pp.233-239
• /
• 2016

In this paper, a maintenance system is developed for LNG-FPSO topside and hullside equipment based CBM (Condition Based Maintenance) methodology. First, the development system defined the PWBS(Product Work Breakdown Structure) of major equipment of LNG-FPSO. Second, the development system developed the failure analysis, economic evaluation for optimal maintenance plan and database systems that save and manage information about equipment, failure mode, failure rate and failure cause. Finally, the verification of the development system was applied to the inlet system of topside and the pump tower system of hullside and the system was confirmed the effectiveness of CBMS(Condition Based Maintenance System).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.5
• /
• pp.1213-1220
• /
• 2015

By the dissemination of the electronic blackboard systems, smart devices, and digital contents, the Korean government is recently conducting the project that replaces the classic education which utilizes paper textbooks with SMART education using various devices. Also, teachers in the field must be easily able to use SMART education infrastructure for the activation of SMART education. Especially, since the electronic blackboard is expected as a education device which will be most common for teachers, the writing software operated on the this device must supports a simple interface. And the usage of it must be simple. In this paper, we developed the writing software for the electronic blackboard which everyone can use easily. Our writing software supports the basic writing function, the human gesture recognition function which recognizes the user gesture and performs works corresponding with that gesture, and the automatic button alignment function based on the frequency of the usages.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2289-2296
• /
• 2016

The password rules to be applied for the user account creation are often different by websites. Thus we often forget the password to sign in website and it creates waste of time for frequent password reset. In order to solve this problem we propose a new authentication method in this paper. When user forget the password to sign in, the existing methods require a password reset step but our proposed method provides new sign in scheme through the additional authentication step with base password and personal information registered at the member sign up stage. From the result of performance comparison the proposed method is considered to be more efficient than others because it provides not only an equivalent level of security with others but also requires only a half of the number of transactions and the time required for password reset step.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.593-602
• /
• 2018

This study examined the impact of trivial baselines obtained from GNSS single-baseline processing into a network adjustment in terms of accuracy and estimated coordinates sets. To this end, depending on the inclusion of the dependent baselines, three different types of experimental GNSS networks were composed and adjusted. The results showed that the networks including the trivial baselines are generally overestimated, but differences in the derived coordinates are limited at the millimeter level. A comparison of the adjusted coordinates with those published by the national geodetic agency showed that results of the network consisting of only the independent baselines are more constant than those of the networks with trivial baselines. Finally, a trivial baseline should be excluded from the GNSS network adjustment with a consideration of the realistic accuracy presentation and data processing burden.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.1-4
• /
• 2012

O- and Zn-polar ZnO films were grown by DC magnetron sputtering. Growth of high-quality, single-crystal ZnO thin films were confirmed by XRD and pole figure analysis. O-polar ZnO was grown on an $Al_2O_3$ substrate, which was confirmed by a slow growth rate (378 nm/hr), a fast etching rate (59 nm/min), and by the hillocks on the surface after etching. Zn-polar ZnO was grown on a GaN/$Al_2O_3$ substrate, which was confirmed by a fast growth rate (550 nm/hr), a slow etching rate (28 nm/min), and by pits on the surface after etching. Results from the present study show that it is possible to use DC-sputtering to grow ZnO film with the same polarity as other epitaxial growth methods.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1057-1063
• /
• 2014

Concerning $CO_2$ reduction from International Societies, lots of laboratories and relevant societies suggest many reports on how to reduce fuel consumption from their specific ways. Undoubtedly, cutting costs is the final desired destination for owner outcome, but many questions there are on the way yet: how is this measure working? how efficient is it? On what size of ship would it work best and be the most effective? etc. Fuel cost is one of the major cost elements for ship owners and/or operators. And by reducing fuel consumption owners and/or operators will reduce both their costs and the environmental impact from their ship. This paper is aim to address how the measures work for saving fuel consumption through improve propulsion efficiency, installation cost and benefit can be calculated easily in the return on investment for estimated one year operation, and finally their compatibility with other fuel saving measure devices.

• Composites Research
• /
• v.31 no.5
• /
• pp.227-237
• /
• 2018

In this paper, the design application for the lightweight and insulation of the manipulator of the mobile welding robot for the closed/narrow space is presented. A variety of robotic platforms have been developed for weld-worker using a welding robot outside a workpiece for welding work in a complex and narrow space such as a ship or an offshore plant. Normally, The development process of robots consists of machine development, electronic device development, control algorithm development and integration verification considering application environment and requirements. In order to develop the robustness of the welding robot, the lightweight design of the robot manipulator considering the environmental conditions was performed in the basic design of the robot platform. Also, The results of the robot selection and validation, analysis and testing for the insulation performance and cooling performance and the results of the research are shown.

• Journal of Korea Multimedia Society
• /
• v.17 no.12
• /
• pp.1473-1483
• /
• 2014

A public restroom is different from a household toilet in terms of location and a large number of sharing users. In addition, public restroom is usually messy and filthy. Recently, public toilet tends to be clearly managed than before, but it still has hygienic and clear problems. In this paper, we propose a machine-to-machine (M2M)-based public restroom management system to solve these problems, in which the system with a wireless communication device sends the status information of the toilet, such as blockage or trouble detected by a sensor, to the manager of the restroom at a remote location. In particular, we have developed a prototype management system for public restroom taking into account several system requirements, and verified the basic operations and performance of the management system. With the application of the system to public facilities, it will furnish users with more pleasant environments by restroom administrators who can respond effectively to the troubled toilet.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.187-192
• /
• 2017

This paper presents an ongoing study to develop a novel pressure sensor by means of a Nano Carbon Piezoresistive Composite (NCPC). The sensor was fabricated using the 3D printing process. We designed a miniaturized cantilever-type sensor electrode to improve the pressure sensing performance and utilized a 3D printer to build a small-sized body. The sensor electrode was made of 2 wt％ MWCNT/epoxy piezoresistive nano-composite, and the sensor body was encapsulated with a pipe plug cap for easy installation to any pressure system. The piezoresistivity responses of the sensor were converted into stable voltage outputs by using a signal processing system, which is similar to a conventional foil strain gauge. We evaluated the pressure-sensing performances using a pressure calibrator in the lab environment. The 3D-printed cantilever electrode pressure sensor showed linear voltage outputs of up to 16,500 KPa, which is a 200％ improvement in the pressure sensing range when compared with the bulk-type electrode used in our previous work.