• International Journal of Internet, Broadcasting and Communication
• /
• 제12권3호
• /
• pp.95-101
• /
• 2020

We studied the Implementation and design of inertial sensor that enables to improve performance by reduce the noise of rotor which Angle of inclination. Analyze model equation including motion equation and error, signal processing filter algorithm on high frequency bandwidth with eliminates error using estimation of error coefficient method is was designed and the prototype inertial sensor showed the pick off noise up to 0.2 mV and bias error performance of about 0.06 deg/hr by the experiments. Accordingly, we confirmed that the design of inertial sensor was valid for high rotation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.660-665
• /
• 1993

An elastic model is developed to predict the average thermal residual stresses in the matrix and fiber of a misoriented short fiber composite. The thermal residual stresses are induced by the mismatch in the coefficient of the thermal expansion of the matrix and fiber when the composite is subjected to a uniform temperature change. The model considers two special cases of fiber misorientation ; two-dimensional in-plane and three-dimensional axisymmetric. The analytical formulation of the model is based on Eshelby's equivalent inclusion method and is nuque in that it is able to account for interactions among fibers. The model is more general than past models and it is able to treat prior analyses of the simpler composite systems as extram cases. The present model is to investigate the effects of fiber volume fraction, distribution type, distribution cut-off angle, and aspect ratio on thermal residual stress for both in-plane and axisymmetric fiber misorientation. Fiber volum fraction, aspect ratio, and disturbution cut-off angle are shown to have more significant effects on the magnitude of the thermal residual stress than fiber distrubution type for both in-plane and axisymmetric misorientation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.139-142
• /
• 2006

This paper describes a new method using random modulated strategies for switched reluctance machines. The proposed method is combined random turn-on, turn-off angle technique and random pulse width modulation technique. The purpose of this proposed method is to decrease harmonic spectrum, and thus reduce the emitted acoustical noise. A random generator is generated by linear congruential generator (LCG) using random pulse position (RPP) scheme. Simulation results show that the harmonic intensity of proposed method is better than that of conventional method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.863_864
• /
• 2009

Design and drive characteristics of SR drive for hydraulic pump system using passive converter is presented in this paper. In oder to get the high performance, a simple passive circuit is added in the front-end of a conventional asymmetric converter, which consists of three diodes and one capacitor. This passive converter has the high demagnetization voltage, to reduce the demagnetization time. Futhermore optimal turn-off angle for the proposed passive converter is proposed. According to motor speed and current, an optimal turn-off angle can be achieved by look-up table to reduce torque ripple. The characteristic of proposed hydraulic pump system using passive converter is verified by simulation and experimental results.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.349-354
• /
• 2001

In this study, we investigated the effect of the impacting ang1e of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozz1e up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA#600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2MPa

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1580-1583
• /
• 2008

We propose an optical configuration for a vertical alignment (VA) liquid crystal (LC) cell to eliminate the off-axis light leakage in the dark state. The proposed compensation configuration consists of a positive A-film, a positive C-film and a negative C-film. The optical design is performed on a Poincar$\acute{e}$ sphere. This configuration has a better tolerance to the wavelength dispersion, as the polarization trace could self-compensate it. From calculations, we show that the proposed VA LC cell can improve the viewing angle characteristics by compensating for the light leakage in the diagonal direction.

• 대한전자공학회논문지
• /
• 제21권4호
• /
• pp.17-23
• /
• 1984

A model analysis of pattern shift in the epitaxial growth of silicon on (111) substrates was performed. The growth rate anisotropy was considered as the most important affecting factor of pattern shift, and for the model establishment the off angle of the substrate and the process temperature were taken as the variables. We derived a theoretical equation of pattern shift by assuming the growth rate anisotropy as the trigonometric sine function of the off angle of the substrate and defining the growth rate anisotropy factor related to the process temperature. The pattern shift ratio calculated by this model had the same tendency with the experimental ones, which, however, were about twice greater than those. It was supposed that this discrepailcy was due to the second order affecting factor such as facetting and step broadening which had been exluded in model establishment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.768-773
• /
• 2001

The self-noise from blade cascade at off-design points mainly comes from separated boundary layer and vortex sheddings, and is also dependent on blade shape. If the incidence angle to the cascade increases, the stalling in blades may occur and the noise level increases significantly. The hybrid method using acoustic analogy was employed to compute the far-field noise spectra and directivity patterns from the separated vortex shedding at off-design points of the cascade of impeller. This paper is compared with the experimental data of a stationary cascade in the same conditions. The simulated result is in excellent .agreement with the measured data except th slight under-prediction near the maximum radiation angle for a dipole sound.

• 한국전자파학회논문지
• /
• 제9권2호
• /
• pp.238-252
• /
• 1998

임의의 편파로서 비스듬한 각도록 입사하는 전자파의경우에 대한 접지돈 유전체층 위에 놓여있는 주기적인 스트립격자 구조에서의 특이한 희절현상을 샘플링 정리와 파수영역 방법을 사용하여 해석하였다. 수치적 결과는 임의의 편파와 TE 및 TM편파가 입사되는 경우에 대하여 각각 Bragg 및 Off-Bragg blazing현상을 확인하고 이에 관하여 논의하였다.

• 설비공학논문집
• /
• 제14권11호
• /
• pp.954-963
• /
• 2002

For the optimal design of an automotive blower system, effects of the scroll cut-off starting angle, the clearance between blade tip and bellmouth, and the scroll expansion angle on the performance of sirocco fan are investigated experimentally. Best performance is achieved at fan exposure ratio $\Deltae/r_c$,/TEX> =1.0, and clearance ratio $\DeltaeC/C=0.62. Flow characteristics inside sirocco fan are also studied by using LDV. Flow patterns in the inside of fan can be classified into three regions. Velocity vector has the same direction as rotational direction of fan at 0~$120^{\circ}$, toward the fan blades at 150～$180^{\circ}$, and opposite direction at 210~$330^{\circ}$. Turbulent intensity is relatively high near the cut-off edge in the scroll housing.