• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.67-78
• /
• 2022

In this study, the measurement results of the coastal deep soft ground buried in the upper part of the dredged clay were analyzed and compared with the current specification standards. Based on the results, a suitable proposal was suggested for the selection, installation, data arrangement, and analysis of each instrument used in the deep soft ground improvement construction. The pore water pressure meter has a range of 1.5 times or more of the expected measurement range, considering the field conditions of the soft ground. The groundwater level meter installed in the horizontal drainage layer checks the change in the groundwater level during the embanking as well as the performance of the catchment well and the horizontal drainage layer. Therefore, it is important to manage so that the groundwater level exists inside the horizontal drainage layer during embanking. It is enough to install the inclinometer in the gravel layer below the soft ground or weathered rock with an N value of 40 or more for the deep soft ground. It seems desirable to install a screw type for differential settlement meter. However, the screw type should not settle due to its own weight. Considering that it is a dredged landfill where subsidence occurs significantly, it is sufficient to manage the tolerance of leveling at about 10 mm (L is the one-way distance (km)).

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1098-1105
• /
• 2021

The International Maritime Organization has steadily strengthened environmental regulations on nitrogen oxides and carbon dioxide emitted from marine vessels. Consequently, the demand for electric propulsion vessels based on eco-friendly elements has increased. To this end, research and development has been steadily conducted for various vessels. In electric propulsion systems, a redundancy configuration is typically adopted to increase reliability and facilitate the onboard arrangement. Furthermore, studies have been actively conducted to ensure the safety of electric propulsion systems through the combination with digital twin technology. A digital twin can be used to predict outcomes in advance by implementing real-world equipment or space in a virtual world like twins, integrating real-world information and data with the virtual world, and performing computer simulations of situations that can occur in a real environment. In this study, we perform failure modes and effects analysis (FMEA) to validate the electric power management system (PMS) redundancy scheme for the digital twin technology development of electric propulsion vessels. Then, we propose the role and algorithm of PMS as a compensation function for preventing primary and secondary damages caused by a single equipment failure of the PMS and preventing additional damages by analyzing the impact on the entire system under real vessel operating conditions based on the redundancy FMEA suggested for the ship classification and certification. We verified the improvement in propulsion conservation through tests.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1011-1022
• /
• 2021

The Korea Coast Guard(KCG) is the only comprehensive maritime administrative agency in Korea that performs various tasks taking place in the ocean, including rescue operations, disaster management, policing, Drug and smuggling crackdown, responding to Response to invasion of maritime territory, environmental conservation, and maritime security. It is vital to inform the public of the role and mission of KCG as the only comprehensive maritime administrative agency in Korea. However, most citizens, excluding residents of the coastal and island areas, have little knowledge of the security administration services of the KCG due to lack of exposure. This study reviewed the KCG's public relations(PR) organization and current status using KCG promotional materials, diagnosed the actual conditions of KCG's PR, and suggested ways to improve public relations activities through a questionnaire survey of public relations personnel. Through literature research and questionnaire survey, the KCG's public relations status was estimated and the measures to enhance publicity was derived as follows: strengthening the PR organization by reinforcing the personnel in charge of PR, improving customized promotion by clarifying the promotion strategy according to the promotion target, enhancing job training for PR personnel, and increasing the interest and support of commanders and internal members in charge of PR work.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.5
• /
• pp.435-444
• /
• 2023

Suitable environmental conditions in Saemangeum frequently favor phytoplankton growth. There have been occurrences of sudden phytoplankton blooms, surpassing the algae management standards. A model was designed to prevent such blooms using scientific predictive techniques to forecast and regulate the possibility of phytoplankton blooms. We propose effective and efficient algae control measures concerning every phytoplankton species optimized through the policy control of nutrients (DIN, PO4-P) from rivers and controlling lake salinity using gate operations. The probability of phytoplankton blooms was initially forecast using an artificial neural network algorithm based on observations. The model's Kappa number fluctuated from 0.7889 to 1.0000, indicating good to excellent predictive power. The Garson algorithm was then utilized to assess the significance of explanatory variables for every species. Meanwhile, the probability of phytoplankton blooms was anticipated depending on the DIN and salinity value changes. Therefore, the model predicted the precise DIN and salinity concentrations to inhibit phytoplankton blooms for each species. Hence, the green algae model can create effective proactive measures to avoid future phytoplankton blooms in enormous artificial lakes.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.7
• /
• pp.17-24
• /
• 2010

Load Resistance Factor Design method is used increasingly in geotechnical design world widely and resistance factors for drilled shafts are suggested by AASHTO. However, these resistance factors are determined for intact rock conditions; by comparison, most of bedrocks in Korea have weathered condition, so that applying the AASHTO resistance factors is not reasonable. Thus, this study suggests the proper resistance factors for design of drilled shaft in Korea. The 22 cases of pile load test data from 8 sites were chosen and reliability-based approach is used to analyze the data. Reliability analysis was performed by First Order Second Moment Method (FOSM) applying 4 bearing capacity equations. As a result, when the Factor of Safety (FOS) was selected as 3.0, the target reliability indexes (${\beta}_c$) were evaluated as 2.01~2.30. Resistance factors and load factors are determined from optimization based on above results. The resistance factors ranged between 0.48 and 0.56 and load factors for dead load and live load are evaluated as approximately 1.25 and 1.75 respectively. However, when the target reliabilities are considered as 3.0, the resistance factors are evaluated as approximately 50% of the results when the target reliability index was 2.0.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.77-85
• /
• 2007

This paper investigates the mechanical characteristics of composite geo-material which was developed to reuse both dredged soils and bottom ash. The composite geo-material used in this experiment consists of dredged soil taken from the construction site of Busan New Port, cement, air foam and bottom ash. Bottom ash is a by-product generated at the Samcheonpo thermal power plant. Several series of laboratory tests were performed to investigate behavior characteristics of composite gee-material, in particular the reinforcing effect by mixing bottom ash. The experimental results of composite geo-material indicated that the stress-strain relationship and the unconfined compressive strength are strongly influenced by mixing conditions. Especially it was observed that the compressive strength of composite geo-material increased with an increase in bottom ash content due to reinforcing effect by the bottom ash. Compressive strength of composite geo-material increased with the increase in curing time. The 28-day strength of composite geo-material is $1.7{\sim}1.8$ times higher than the 7-day strength. The moist unit weight strongly depended on air-foam content as well as bottom ash content added to the composite goo-material. In composite geo-material, secant modulus ($E_{50}$) also increased as its compressive strength increased due to the inclusion of bottom ash.

• Resources Recycling
• /
• v.32 no.3
• /
• pp.38-44
• /
• 2023

Leaching tests were conducted using sulfuric acid and sodium hydroxide solutions to remove impurities from domestic graphite concentrate. As a result of the leaching experiment using sulfuric acid solution and sodium hydroxide solution, respectively, the difference of removal efficiency was insignificant when the concentration of sodium hydroxide or sulfuric acid was 2 mol/L or more. The fixed carbon content increased with increasing the temperature in the sulfuric acid solution leaching, while it remains constant above 150℃ in sodium hydroxide solution. For the repeated sequential leaching tests, the leaching conditions were 2 mol/L NaOH, 200℃, 1 hour in the sodium hydroxide solution leaching and 2 mol/L H₂SO₄, 100℃, 1 hour in the sulfuric acid solution leaching, respectively. When sulfuric acid leaching followed by sodium hydroxide solution leaching was repeated 5 times, the fixed carbon increased to 99.95% and ash content decreased to 0.048%, while the fixed carbon increased to 99.98% and ash content was reduced to 0.018 when sodium hydroxide solution leaching followed by sulfuric acid solution leaching was repeated 5 times.

• Korean Journal of Remote Sensing
• /
• v.39 no.6_1
• /
• pp.1477-1482
• /
• 2023

This study examines marine heat wave (MHW) in the Northeast Asia region from 2012 to 2021, utilizing geostationary satellite Communication, Ocean, and Meteorological Satellite (COMS)/Meteorological Imager sensor (MI) and GEO-KOMPSAT-2A (GK-2A)/Advanced Meteorological Imager sensor (AMI) Sea Surface Temperature (SST) data. Our analysis has identified an increasing trend in the frequency and intensity of MHW events, especially post-2018, with the year 2020 marked by significantly prolonged and intense events. The statistical validation using Optimal Interpolation (OI) SST data and satellite SST data through T-test assessment confirmed a significant rise in sea surface temperatures, suggesting that these changes are a direct consequence of climate change, rather than random variations. The findings revealed in this study serve the necessity for ongoing monitoring and more granular analysis to inform long-term responses to climate change. As the region is characterized by complex topography and diverse climatic conditions, the insights provided by this research are critical for understanding the localized impacts of global climate dynamics.

• Composites Research
• /
• v.36 no.6
• /
• pp.454-460
• /
• 2023

Recently, regulations on greenhouse gas emissions have been strengthened, and the International Maritime Organization (IMO) has been strengthening greenhouse gas regulations with a goal of net 'zero' emissions by 2050. In addition, in the shipbuilding/offshore sector, it is important to reduce operating costs, such as improving propulsion efficiency and lightening structures. In this regard, research is currently being conducted on topology optimization using 3D printed composite materials to satisfy structural lightness and high rigidity. In this study, three topology shapes (hexagonal, square, and triangular) were applied to the interior of a rudder, a ship structure, using 3D printed composite materials. Structural analysis was performed to determine the appropriate shape for the rudder. CFD analysis was performed at 10° intervals from 0° to 30° for each rudder angle under the condition of 8 knots, and the load conditions were set based on the CFD analysis results. As a result of the structural analysis considering the internal topology shape of the rudder, it was confirmed that the triangular, square, and hexagonal topology shapes have excellent performance. The rudder with a square topology shape weighs 78.5% of the rudder with a triangular shape, and the square topology shape is considered to superior in terms of weight reduction.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.15 no.1
• /
• pp.16-24
• /
• 2010

Utilization of dissolved organic phosphorus (DOP) and alkaline phosphatase (APase) activity by Skeletonema costatum, Chaetoceros didymus, Alexandrium tamarense and Heterosigma akashiwo under the phosphorus deficient condition were examined in the laboratory. S. costatum, C. didymus, A. tamarense and H. akashiwo could make use of phosphomonoester and nucleotide compounds for the growth of them as a phosphorus source. APase activity of S. costatum, C. didymus, A. tamarense and H. akashiwo began to be activated at dissolved inorganic phosphorus (DIP) concentrations less than $0.30\;{\mu}M$, $0.33\;{\mu}M$, $2.04\;{\mu}M$ and $0.63\;{\mu}M$ respectively, and their maximum APase activity were $0.01\;pmol\;cell^{-1}\;hr^{-1}$, $0.11\;pmol\;cell^{-1}\;hr^{-1}$, $1.63\;pmol\;cell^{-1}\;hr^{-1}$ and $0.19\;pmol\;cell^{-1}\;hr^{-1}$, respectively. Although each phytoplankton species displayed different APase activity for DOP utilization, their maximum APase activities were higher than maximum phosphorus uptake rates, inferring that these species might be able to keep growing under DIP-limited conditions thought utilizing effectively the hydrolized product of DOP. This result also implies that utilization of DOP might contribute to not only the growth of red tide forming phytoplankton but also the interspecific competition among phytoplankton species in coastal environments.