• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.112-121
• /
• 1988

A study on friction welding of carbon steel bar (SM45C) to chrome molybedenum steel bar(SCM4) is examined experimentally through tensile test, hardness test, microstructure test and fatigue test. so, this paper deals with optimizing the welding concitions and analyzing various mechanical properties about friction welds of SM45C to SCM4 steel bars. The results obtained are summarized as follows; 1) For friction welded joints of SM45C to SCM4 steel bars, the total upset(U)increases linearly with an increase of heating time ($t_{1}$) till 6s. 2) The determined optimum welding conditions are heating time ($t_{1}$)2s, upsetting time($t_{2}$), 3s, heating pressure($p_{1}$), 4kgf/$mm^{2}$(39.2MPa), upsetting pressure($p_{2}$, 8kgf/mm$^{2}$(78.4MPa) and rotating speed(N), 2, 000rpm when the total upset(U) is 3.4mm, resulting in a computed relationship between the joint tensile strength .sigma.$_{t}$ (kgf/mm$^{2}$and the total upset U(mm); .sigma.$_{t}$ =$0.21U^{3}$ - $3.38U^{2}$ +17.03U + 66.00 3) As the elongation is increased more and more, the fracture position becomes away from weld interface and the fractures are similar to those of SM45C. Fracture is taken place on SM45C side. 4) The weld interface of two dissimilar materials is mixed strongly, and the heat affected zone is about 2.0mm at SM45C while about 2.7 mm at SCM4 side. Therefore, the welded zone and heat affected zone are very narrow, comparing with those of the joints welded by the other welding methods. 5) The fatigue strengths at N=10$^{6}$ cycles of SM45C, SCM4 and friction welded joints are 23kgf/$mm^{2}$, 33kgf/$mm^{2}$(220.5 MPa), and 22.5kgf/$mm^{2}$(220.5MPa) respectively, and fracture at friction welded joint takes place at the side of SM45C. 6) The hardness of the friction weld interface is 3 times higher than that of base metal. 7) Fatigue strength of friction welded joint is higher than that of base metal. 8) Notch sensitivity factor of friction welded joint is lower than that of base metal.

• Journal of Mechanical Science and Technology
• /
• v.20 no.1
• /
• pp.42-50
• /
• 2006

To evaluate the fatigue lifetime of structures, it is necessary to identify the values of parameters through tests. From the viewpoint of time and cost it is difficult for engineers to get the necessary data through tests. In this study, we surveyed literature and proposed a procedure to identify the fatigue parameters expressed with the Brinell hardness and elastic modulus. After obtaining stress concentration factors by finite element analysis, we calculated fatigue notch factors using Peterson's formula. Taking into account the welding residual stress, which was also obtained by finite element analysis, we evaluated the fatigue lifetime of four kinds of welded joints using the proposed approach. The estimated results are in a good agreement with the experimental results.

• ETRI Journal
• /
• v.29 no.2
• /
• pp.237-239
• /
• 2007

Interference from IEEE 802.11a systems affects ultra-wideband (UWB) systems significantly. In this letter, we suggest a novel narrow-band interference (NBI) suppression technique based on the singular value decomposition (SVD) algorithm in time-hopping pulse amplitude modulation (TH-PAM) UWB systems. The SVD algorithm is used to approximate the interference which then is subtracted from the received signals. In contrast to the conventional notch filter and rake receiver, our method is more effective and the receiver complexity can be greatly reduced.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.149-157
• /
• 2000

Computer simulations of the mechanical behavior of a three point bend specimen with a quarter notch under impact load are performed. The case with a load application point at the side is considered. An elastic-plastic von Mises material model is chosen. Three phases such as impact bouncing and bending phases are found to be identified during the period from the moment of impact to the estimated time for crack initiation. It is clearly shown that no plastic deformation near the crack tip is appeared at the impact phase. However it is confirmed that the plastic zone near the crack tip emerges in the second phase and the plastic hinge has been formed in the third phase. Gap opening displacement crack tip opening displacement and strain rate are compared with rate dependent material(visco-plastic material). The stability during various dynamic load can be seen by using the simulation of this study.

• Journal of Biomedical Engineering Research
• /
• v.22 no.3
• /
• pp.285-291
• /
• 2001

In this paper, we designed two preprocessing adaptive filter - high pass filter and notch filter - using FPGA. For minimizing the calculation load of multi-channel and high-resolution ECG system, we utilize FPGA rather than digital signal processing chip. To implement the designed filters in FPGA, we utilize FPGA design tool(Altera corporation, MAX-PLUS II) and CSE database as test data. In order to evaluate the performance in terms of processing time, we compared the designed filters with the digital filters implemented by ADSP21061(Analog Devices). As a result, the filters implemented by FPGA showed better performance than the filters based on ADSP21061. As a consequence of examination, we conclude that FPGA is a useful solution in multi-channel and high-resolution signal processing.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.398-403
• /
• 2004

The demand of high speed machining is increasing because the high speed cutting providers high efficiency of process, short process time, improved metal removal capacity and better surface finish. Active magnetic bearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting. The automatic control concept of magnetic bearing system provides ability of intelligent control of spindle system to increase accuracy and flexibility by means of adaptive vibration control. This paper describes a design and development of a milling spindle system which includes built-in motor with power 5.5㎾ and maximum speed 70,000rpm, HSK-32C tool holer and active magnetic bearing system. Magnetic actuators are designed for satisfying static load condition. The Performances of manufactured spindle system was examined for its static and dynamic stiffness, load capacity, and rotational accuracy. This spindle was run up to 70,000 rpm stably, which is 3.5 million DmN.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2477-2479
• /
• 2005

A robust bending frequency tracker is proposed to design the adaptive notch filter which removes the time-varying missile structural modes from the sensor measurements. To do this, the state-space form of a bending frequency model is derived under the assumption that the bending signal could be described as the lightly damped sinusoid. Since the resultant bending frequency model contains the parametric uncertainties in the measurement matrix, the design problem of bending frequency tracker is tackled by applying the robust Kalman filter to the model. This technique could be easily expanded to the multiple frequencies case because it newly illuminates the bending frequency tracking problem in view of general state estimation.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.322-327
• /
• 2003

In this study, the single notched specimen which was proposed the previous study was used to evaluate of the transverse tensile property of zircaloy cladding. The single notched specimen has notches which give stress intensity effect, so both FEM and experiment are needed for the same time. Take a coincidence of tensile behavior about both FEM and experiment, then obtain stress and strain from FEM only. The influence of notch was estimated by comparing the result of experimental, FEM. Then the relationship between stress-strain and displacement was evaluated.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.170-175
• /
• 1992

A leak detection method for diagnosis of the leak position in a pipeline was developed using an estimation theory with the assumption that the measured flow rates and pressures are stochastic processes. A notch filter was designed using power spectral density analysis of measurements to reduce the effects of disturbances. The noise model dimension was determined by hypothesis testing and then recursive extended least square method was applied to estimate the leak position in real time. The proposed method was applied to an experimental system for evaluation of its performance.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.8-11
• /
• 2003

For the first time to our knowledge we have developed compact mechanically-induced long-period fiber grating devices which have an excellent tunability in the center wavelength and the depth of the notch. The compactness and ease to tune allow us to include them in other optical devices or systems. The devices were characterized by measuring their transmission spectra with different grating periods and applied pressures. We have also demonstrated the EDFA gain flattening using the mechanically-induced long-period fiber grating devices.