• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.25-30
• /
• 2018

Closed-form analytical expressions and 3-dimensional normalized charts for the homogeneous sensing and surface sensing structures are derived to provide the conditions for the maximum sensitivity of integrated-optic biosensors based on evanescent-wave and stepindex planar optical waveguides. The analysis is made for transverse electric (TE) polarization mode, in both cases where the measurand is homogeneously distributed in the cover (namely, homogeneous sensing), and where it is an ultrathin film on the waveguide-cover interface (namely, surface sensing).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.11
• /
• pp.759-766
• /
• 2012

To estimate the cooling load for the following day, outdoor temperature and humidity are needed in hourly base. But the meteorological administration forecasts only maximum and minimum temperature. New methodology is proposed for predicting hourly outdoor temperature and humidity by using the forecasted maximum and minimum temperature. The correlations for normalized outdoor temperature and specific humidity has been derived from the weather data for five years at Seoul, Daejeon and Pusan. The correlations for normalized temperature are independent of date, while the correlations for specific humidity are linearly dependent on date. The predicted results show fairly good agreement with the measured data. The prediction program is also developed for hourly outdoor dry bulb temperature, specific humidity, dew point, relative humidity, enthalpy and specific volume.

• East Asian mathematical journal
• /
• v.21 no.2
• /
• pp.233-240
• /
• 2005

Let $CS^{\alpha}(\beta)$ denote the class of normalized strongly $\alpha$-logarithmic close-to-convex functions of order $\beta$, defined in the open unit disk $\mathbb{U}$ by $$\|arg\{\(\frac{f(z)}{g(z)}\)^{1-\alpha}\(\frac{zf'(z)}{g(z)\)^{\alpha}\}\|\leq\frac{\pi}{2}\beta,\;(\alpha,\beta\geq0)$$ where $g{\in}S^*$ the class of normalized starlike functions. In this paper, we prove sharp $Fekete-Szeg\"{o}$ inequalities for functions $f{\in}CS^{\alpha}(\beta)$.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.1
• /
• pp.30-35
• /
• 2010

As of today, Frequency Hopping techniques are widely used for over-channel interference and anti-jamming communication systems. In this paper, analysis the performance of robustness on the focus of some general jamming channel. In FH/SS systems, usually SFH(Slow Frequency Hopping) and FFH(Fast Frequency Hopping) are took up on many special communication systems, the SFH, FFH are also combined with a channel diversity algorithm likes NED(Normalized Envelop Detection), EGC(Equal Gain Combines) and Clipped Combines to overcome jammer's attack. This paper propose Adaptive-NED and shows A-NED will be worked well than the others in the some general jamming environments.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.146-155
• /
• 1997

In order to achieve scale- and rotation-invariance in recognizing unoccluded objects in binary images using Zernike moment features, an image of an object has often been normalized first by its zeroth-order moment (ZOM) or area. With elongated objects such as characters, a stroke width varies with the threshold value used, it becomes one or two pixels wider or thinner. The variations of the total area of the character becomes significant when the character is relatively thin with respect to its overall size, and the resulting normalized moment features are no longer reliable. This dilation/erosion effect is more severe when the object is not focused precisely. In this paper, we analyze the ZOM method and propose as a normalization method, the maximum enclosing circle (MEC) centered at the centroid of the character. We compare both the ZOM and MEC methods in their performance through various experiments.

• Steel and Composite Structures
• /
• v.27 no.4
• /
• pp.401-416
• /
• 2018

Composite beams with web openings are vulnerable to Vierendeel bending failure. The available methods provide quite conservative estimates of Vierendeel bending resistance. An alternative design method to compute the resistance was proposed in this study, based on quadratic nonlinear interactions of normalized shear force, axial force and Vierendeel bending moment. The interactions of the top and bottom Tee section must satisfy mutual conditions to prevent the Vierendeel failure. The normalized shear force and Vierendeel bending moment of the composite part were used instead in the top Tee interaction. The top Tee axial force was computed based on force equilibrium. Based on a rigid-plastic model, the composite resistance is estimated using an effective slab width of the vertical shear resistance. On using the proposed method, nonlinear reductions due to shear loads and axial forces are not required, in contrast to prior methods. The proposed method was validated against experiments from literature. The method limitations and accuracy as well as the Vierendeel behavior were investigated by finite element simulations, with varied composite beam parameters. The proposed design loads are less conservative than earlier estimates and deviate less from the simulations.

• Smart Structures and Systems
• /
• v.25 no.6
• /
• pp.669-678
• /
• 2020

This paper focuses on the free vibration analysis of axially functionally graded (FG) Euler-Bernoulli beams. The material properties of the beams are assumed to obey the linear law distribution. The complexities in solving differential equation of transverse vibration of composite beams which limit the analytical solution to some special cases are overcome using the Differential Transformation Method (DTM). Natural frequencies and corresponding normalized mode shapes are calculated. Validation targets are experimental data or finite element results. Different parameters such as reinforcement distribution, ratio of the reinforcement Young's modulus to the matrix Young's modulus and ratio of the reinforcement density to the matrix density are taken into investigation. The delivered results prove the capability and the robustness of the applied method. The studied parameters are demonstrated to be very crucial for the normalized natural frequencies and mode shapes.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.40-47
• /
• 2000

This paper presents a circuit of resonant voltage resultant type DC/DC converter consists of two unit half-bridge high frequency resonant inverters, and describes operating modes, principle and analysis of the proposed circuit. Also, the analysis of the proposed circuit has generally described by using normalized parameters. Based on the characteristic values, a method of the circuit design is proposed. According to phase shift, the output voltage of the proposed circuit can be controlled. In addition, the justification of theoretical analysis was certified by comparing to the experimental waveforms. In the future, this proposed converter show that it can be practically used as the system of fixed DC voltage source etc.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.4
• /
• pp.537-544
• /
• 2013

This paper proposes a recursive localized Normalized Mutual Information(NMI) algorithm to overcome shortcomings of the conventional NMI algorithm and the localized NMI algorithm which proposed before. The localized NMI algorithm divides images into few fixed size segments and applies NMI algorithm to each segments. By extension, the proposed algorithm uses variable size segments using its characteristic. Dividing each segment recursively, the algorithm selects a suitable segment size and improves a performance of the image registration. Experimental result shows the performance of the proposed algorithm.

• Journal of Electrical Engineering and information Science
• /
• v.1 no.2
• /
• pp.119-124
• /
• 1996

Variable step size LMS(VS-LMS) algorithms improve performance of LMS algorithm by means of varying the step size. This paper presents a new VS-LMS algorithm using normalized absolute estimation error. Normalizing the estimation error to the expected valus of the desired signal, we determined the step size using the relative size of estimation error, Because parameters and computational load are less, our algorithm is easy to implement in hardware. The performance of the proposed algorithm is analyzed theoretically and estimated through simulations. Based on the theoretical analysis and computer simulations, the proposed algorithm is shown to be effective compared to conventional VS-LMS algorithms.