• Journal of the Korean Vacuum Society
• /
• v.8 no.4B
• /
• pp.556-564
• /
• 1999

The analysis on heat fluxed on and transmission efficiencies by the collimators of neutral beam injection lines in KSTAR tokamak device has been carried out. And a mathematical model describing non-Gaussian beam distribution profile has been established. A neutral beam injection device is composed of 3 separate ion sources and corresponding beam transport lines, which deal with 7.8 MW of beam power, respectively. The divergence angles of ion beam are $1.2^{\circ}$and $0.5^{\circ}$, in vertical and horizontal directions, respectively. The maximum normal heat load on source exit scraper is 9.1 kW/$\textrm{cm}^2$ and net beam transmission efficiency is ~28%. The effect of misalignment of ion source and scrapers on the scraper heat load and beam transmission also has been analyzed.

• Publications of The Korean Astronomical Society
• /
• v.14 no.1
• /
• pp.1-8
• /
• 1999

We performed VRI CCD surface photometry of three spiral galaxies of HCG10 in order to understand the effect of interactions in the compact group. The morphology of the largest member NGC 536 seems to be normal but its bulge is thought to be of an oblate spheroid. The central surface brightness of the disk of NGC 536 is much fainter than that of disks of nearby spiral galaxies. The morphologies of NGC 531 and NGG 542 appear to be affected by interactions which lead to a warped disk in NGC 531 and a slightly bent disk in NGC 542. NGC 531 have a boxy bulge and a Freeman Type II disk both of which strongly suggest the presence of a bar in the galaxy. There is a break in the slope of the luminosity profile of NGC 542 which is dominated by the disk component.

• Journal of Oral Medicine and Pain
• /
• v.6 no.1
• /
• pp.35-44
• /
• 1981

This study was undertaken to investigate the values of Gonial angle of the aged from 50 to 87 which consisted of 75 males and 47 females and the other values of the cephalometric standards of the aged which consisted of 42 males and 26 females with normal occlusion and acceptable profile. Each lateral cephalometric head films were taken with the teeth in occlusion utilizing the Siemens Cephalometer. The following conclusions were obtained : 1. The author made the tables of standard deviation from the measured values. 2. The degree of the Gonial angel of the aged was larger than that of Korean adults. 3. The degree of length in the values of the cephalometric standards of old aged men was larger than that of women.

• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.12 no.2
• /
• pp.84-95
• /
• 2008

Background and purpose: Health is characterized by variability and a loss variability is associated with aging and disease. Normal healthy respiratory patterns are characterized by breath to breath variability. The aim of this study is to analyze Correlation Analysis of 10 respiratory indices(include breath to breath variability) and K-POMS factors score. Method: Respiratory data were measured during 15 minutes and transferred to text file. We calculated 10 respiratory parameters in use of MATLAB7.1. After then do correlation analysis of 10 respiratory indices and K-POMS factors score. Result and conclusion: Respiratory variability is showed significant correlation with vigor factor. Respiratory rate is showed significant correlation with depression factor.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1294-1296
• /
• 1998

Platinum thin films which hardly form volatile compounds with any reactive gas at normal process temperature was etched in Inductively Coupled Plasma (ICP) using Ar/HBr/$Cl_2$ gases. It is observed that the etch rate of platinum is reduced as increasing of HBr/$Cl_2$ gas mixing ratio when Ar gas ratio is fixed. However, we obtain good etching profile of platinum films without unwanted residues in 90% Ar/5% HBr/5% $Cl_2$ gas mixing ratio.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.5 no.1
• /
• pp.22-25
• /
• 1975

The author has studied on the profiles on Korean young male and female by the cephalometric roentgenograms, the subjects were consisted of 104 persons with normal occlusion and the measurements were done on the soft and hard structures. The mean and standard deviations in the subjects were calculated and compared between male and female. The author has obtained the following results: 1. In the linear measurement, male was longer than female in most measuring points. 2. Compared with the angulation of soft tissue, there were no differences between both sexes. 3. In the skeletal patterns, there were some differences between male and female, but there was a similarity to the facial profile. 4. The individual variations on the cephalometric profiles on the subjects were recognized, especially, in the lower facial part.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.241-246
• /
• 2000

Gas hydrates are solid solutions when water molecules are linked through hydrogen bondin create host lattice cavities that can enclose a large variety of guest gas molecules. The natural hydrate crystal may exist at low temperature above the normal freezing point of water and pressure greater than about 30 bars. A lot of quantities of natural gas hydrates exists in the ear many production schemes are being studied. In the present investigation, depressurization method considered to predict the production of gas and the simulation of the two phase flow - gas and - in porous media is being carried out. The simulation show about the fluid flow in porous have a variety of applications in industry. Results provide the appearance of gas and water prod the pressure profile, the saturation of gas/ water/ hydrates profiles and the location of the pl front.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.670-673
• /
• 2003

Fabrication of three dimensional microstructures by laser-assisted chemical vapor deposition of material is investigated. To fabricate microstructures, a thin layer of deposit in desired patterns is first written using laser direct writing technique and on top of this layer a second layer is deposited to provide the third dimension normal to the surface. By depositing many layers. a three dimensional microstructure is fabricated. Optimum deposition conditions for direct writing of initial and subsequent layers with good surface quality and profile uniformity are determined. Using an arson ion laser and ethylene as the light source and reaction gas, respectively, fabrication of three-dimensional carbon microstructures is demonstrated.

• Steel and Composite Structures
• /
• v.9 no.6
• /
• pp.519-534
• /
• 2009

This study intends to examine the characteristics of compressive behavior and conducts comparative analysis between normal compressive strength under existing equations (LRFD, ACI 318, EC 4) and experimental the maximum compressive strength from the compression experiment for the unstiffened steel plate-concrete structures. The six specimens were made to evaluate the constraining factor (${\xi}$) and width ratio (${\beta}$) effects subjected to the compressive monotonic loading. Based on this experiments, the following conclusions could be made: first, compressive behaviors of the specimens from the finite element analysis closely agreed with the ones from the actual experiments; second, the higher the width ratio (${\beta}$) was, the lower the ductility index (DI) was; and third, the test results showed the maximum compressive strength with a margin by 7% compared to the existing codes.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.11
• /
• pp.1096-1103
• /
• 2010

This paper proposes CDC (Continuous Damping Control) algorithm and verifies in multi-body dynamic vehicle. In order to distinguish a road profile on driving, waviness calculated by the filtered vertical-accelerations of sprung and unsprung masses is introduced. Sky-hook control is used at a low waviness road and constant damping level control is used at a high waviness road, where the hard damping level is determined by waviness, roll rate, acceleration, and deceleration. The damping levels of ride, anti-roll, anti-squat, and anti-dive modules are calculated by tuning parameters which is dependent upon vehicle velocity. Therefore this high tunable algorithm is useful to improve the ride and handling performance under various driving conditions. In the simulations, tire and dampers are modelled by SWIFT (Short Wavelength Intermediate Frequency Tire) model and 1st order delay model, and results are compared with conventional damper's.