• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.539-547
• /
• 2018

Grid-connected inverter is required to cut off the power supplied to the grid at the islanding condition, immediately. For this reason, an islanding detection is an indispensable function for grid-connected distributed generation system. Slip-Mode frequency Shift (SMS) islanding detection method is very popular method to determine the grid state. SMS method supplies the reactive power to the load according to the grid frequency. In the islanding condition of grid, this injected reactive power pulls out the grid frequency from the allowable range, then the inverter system can detect the islanding condition of the grid. The SMS method can detect the islanding state well and does not generate any harmonics of the grid current. However, the reactive power would be generated and the power quality is reduced even though the grid is not islanding condition, but normal condition. In this paper, a modified SMS method is proposed to remove the reactive power in the normal condition. The performance of the proposed method is evaluated by 600W single phase inverter experimental results.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.4
• /
• pp.38-46
• /
• 1993

This study is to analyze effect of exposure environment and mode of ASR on the engineering properties of synthetic lightweight aggregate concrete, such as dynamic modulus of elasticity and ultrasonic pulse velocity. The results of this study are summarized as foflows ; 1. The expansion rate of each exposure environment in 380$^{\circ}$C and NaCI 4% solution was shown higher than in 20$^{\circ}$C and normal water. The expansion rate of each exposure mode was largely shown in order of fjill immersion, wetting/drying, half immersion. 2. The dynamic modulus of elasticty and ultrasonic pulse velocity of each exposure environment in 38$^{\circ}$C and NaCl 4% solution was shown less than in 20$^{\circ}$C and normal water. The dynamic modulus of elasticity and ultrasonic pulse velocity of each exposure mode was shown smaller in order of full immersion, wetting/drying, half imersion.3. The relation between dynamic modulus of elasticity and ultrasonic pulse velocity was highly significant. The dynamic modulus of elasticity was increased with increase of ultrasonic pulse velocity. The decreasing rate of the dynamic modulus of elasticity was shown 2.1~3.4 times higher than the ultrasonic pulse velocity at each age, exposure environment and mode, respectively. 4. The expansion of each exposure environment and mode was increased with increase of curing age. The dynamic modulus of elasticity and ultrasonic pulse velocity of those concrete was increased with increase of curing age. At the curing age 28 days, the highest properties was showed at each type concrete, it was gradually decreased with increase of curing age. Specially, at the curing age 98 days of full immersion, the rate of expansion of type D was shown 3.95 times higher than the type A. But the dynamic modulus of elasticity and ultrasonic pulse velocity was decreased 17% and 8.3%.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.19 no.2
• /
• pp.27-31
• /
• 1982

The practical utilization of the frequency and normal mode equations of uniform Timoshenko beams such as those presented by Huang is not simple due to their highly trancendental nature. In this note largely simplified equations obtained for the fixed-fixed and the free-free boundary conditions, the modes of which are separable into symmetric modes and antisymmetric ones, are given. Numerical results obtains for six common-type boundary conditions show that the quantitative measure of the effect of rotary inertia and shear deformation on the natural frequency is greatly dependent upon the boundary conditions as well as the order number.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.550-553
• /
• 1993

Methods of Alternating Noise Canceling were previously developed for the optical instrumentation;one using a dual photo sensor and another using a single photo sensor that could cancel normal mode noise on a transmission line, even if the noise was of equal status noise. But the methods could not remove noise on sensor line. This paper discusses a new method of using a photo sensor with a resistance sensordummy, effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrumentation. The accuracy of this method has been verified by experiments using sinusoidal wave as an equal status noise on a sensor line and/or rectangular wave as an equal status wide band noise on a transmission line respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.397-402
• /
• 2007

Application of hydroforming technology for Engine Cradle has done much to reduce the weight of it. In most cases, hydroformed member of Engine Cradle is made in one-piece. And this method cause a limeted design that amount of expansion at the center portion of the member is not enough to meet the required performance. This limited design leads to decrease the dynamic characteristics of Engine Cradle. In this paper, comparative analyses of conventional stamped engine cradle and hydroformed cradle of one-piece were conducted using Normal Mode analysis and FRF(Frequancy Response Function)analysis. Finally, to improve the disadvantage mentioned above, hydroformed member of 3-pieces was proposed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.736-741
• /
• 2012

Squeak noise is studied by using the pin-on-disk system with aluminum pin and steel disk. Noise induced by friction is measured with respect to the normal loads and sliding speeds. The negative slope of friction-velocity curve is seen when the squeak noise occurs. It is found that the normal load influences on the sound level of squeak noise. From the hammering test, the major frequency of the squeak noise is shown to correspond to one of system modes, which implies that squeak phenomenon arises from the unstable system modes. The result of FE analysis shows that the major squeak mode is the bending mode of the pin.

• Tribology and Lubricants
• /
• v.15 no.3
• /
• pp.265-271
• /
• 1999

Wherever there are rotating equipment and contact between surface, there is wear and the generation of wear particles. The particles contained in the lubricating oil carry detailed and important information about the condition monitoring of the machine. This information may be deduced from particle shape, composition, size distribution, and concentration. Therefore, This paper was undertaken to Ferrography system of wear debris generated from lubricated moving machine surface. The lubricating wear test was performed under different experimental conditions using the Falex wear test of Pin and V-Block type by Ti(C, N) coated. It was shown from the test results that wear particle concentration (WPC) and wear severity Index( $I_{S}$), size distribution in normal and abnormal wear have come out all the higher value by increases sliding friction time. Wear shape is observed on the Ferrogram it was discovered a thin leaf wear debris as well as ball and plate type wear particles. This kind of large wear shape have an important effect not only metals damage, but also seizure phenomenon.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.218-220
• /
• 2007

A new 3-phase voltage disturbance generator is proposed. The voltage drop of the conventional generator in normal mode can be reduced significantly. The output voltage of the proposed generator is constant in normal mode and the efficiency of the series transformer is improved. The proposed generator has good feature of simple structure, cost effective implementation, high reliability, high efficiency, and easy control. The usefulness of the scheme is verified through simulation and experiments.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.579-592
• /
• 2016

CNUSAIL-1, to be launched into low-earth orbit, is a cubesat-class satellite equipped with a $2m{\times}2m$ solar sail. One of CNUSAIL's missions is to deploy its solar sail system, thereby deorbiting the satellite, at the end of the satellite's life. This paper presents the design results of the attitude control system for CNUSAIL-1, which maintains the normal vector of the sail by a 3-axis active attitude stabilization approach. The normal vector can be aligned in two orientations: i) along the anti-nadir direction, which minimizes the aerodynamic drag during the nadir-pointing mode, or ii) along the satellite velocity vector, which maximizes the drag during the deorbiting mode. The attitude control system also includes a B-dot controller for detumbling and an eigen-axis maneuver algorithm. The actuators for the attitude control are magnetic torquers and reaction wheels. The feasibility and performance of the design are verified in high-fidelity nonlinear simulations.

• Structural Engineering and Mechanics
• /
• v.74 no.4
• /
• pp.471-479
• /
• 2020

This paper aims to study the effect of the elastic nonlocality on the transient waves in a two-dimensional thermoelastic medium influenced by thermal loading due to the laser pulse. The bounding plane surface is heated by a non-Gaussian laser beam. The problem is discussed under the Eringen's nonlocal elasticity model and the Green-Naghdi (G-N) theory with and without energy dissipation. The normal mode analysis method is used to get the exact expressions for the physical quantities which illustrated graphically by comparison and discussion. The effects of nonlocality and different values of time on the displacement, the stresses, and the temperature were made numerically. All the computed results obtained have been depicted graphically and explained.