• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.1118-1120
• /
• 2003

In MSC(Multi-spectral camera ), the incoming light is converted to electronic analog signals by the CCD(charge coupled device) detectors. The analog signals are amplified, biased and converted into digital signals (pixel data stream) in the FPE(Focal plane electronics ). The digital data is transmitted to the PMU for pre-processing to correct for nonuniformity, to partially reorder the pixel stream and to add header data for identification and synchronization In this paper, the video data streams is described in terms of hardware.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.450-450
• /
• 2010

Recently, field emission emitters made by carbon nanotubes(CNTs) and ink-jet method have been extensively studied due to their low cost, little limitation of size and a high resolution. When CNT emitters are operated, a few highly protruded ones generate most of the emission currents that cause spatial nonuniformity. In this study, we applied selective oxidation to solve this problem on ink-jet printed CNT emitters. Consequently, O2 exposures to field emitting CNT arrays give rise to a permanent damage selectively on the highly emitting CNTs. In spite of turn-on field increase, emission images was showed remarkably uniform after oxygen trimming.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.42-49
• /
• 2003

In this paper, we provide the results of polishing temperature distribution by way of infrared ray measurement system as well as polishing resistance, which can be interpreted as tribological aspects of CMP, using force measurement system. The results include the trend of polishing temperature, its distribution profile and temperature change during polishing. The results indicate that temperature affects greatly to the removal rate. Polishing temperature increases gradually and reaches steady state temperature and the period of temperature change occurs first tens of seconds. Furthermore, the friction force also varies as the same pattern with polishing temperature from high friction to low. These results suggest that the first period of the whole polishing time greatly affects the nonuniformity of removal rate.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.156-165
• /
• 1994

Unsteady heat conduction in stacked disks in a furnace has been numerically solved The effects of relevant parameters such as disk spacing, aspect ratio, environmental temperature, Biot nember, etc. have been investigated. The highest temperature appears at the disk edge and the lowest at the center. Penetration of heat form the surface to the center requires some time. Heating should be slow for uniform temperature rise. Geometric parameters complicates the radiative and conductive heat transfer. Though the resulting dependence of temperature nonuniformity on various parameters is complicated, high uniformity of temperature is in general available by low Biot number and/or low environmental temperature.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.574-578
• /
• 2008

In order to achieve thrust vector control and discharge stabilization in Hall thrusters, the azimuthal nonuniformity of propellant flow rate in an acceleration channel was created. A plenum chamber was divided into two rooms by two walls and propellant flow rate supplied to each section was independently controlled. In a magnetic layer type Hall thruster, steering angle of up to ${\pm}2.3$ degree was achieved. In an anode layer type Hall thruster, discharge current oscillation amplitude was decreased with the normalized differential mass flow rate.

• 조명전기설비학회논문지
• /
• 제27권2호
• /
• pp.1-6
• /
• 2013

In this paper, we implemented a polarimetric strain sensor using a Sagnac birefringence interferometer composed of a polarization-maintaining photonic crystal fiber (PM-PCF). By changing the length of the PM-PCF employed as the sensor head of the proposed sensor, the length dependence of the strain sensitivity was investigated. With respect to 5.0-, 7.5-, and 10.0-cm-long PM-PCFs, strain measurements were done in a measurement range of $0{\sim}6m{\varepsilon}$, and strain sensitivities of ~2.04, ~1.92, and ${\sim}1.73pm/{\mu}{\varepsilon}$ were obtained, respectively. If an ideal PM-PCF with no length dependence of a modal birefringence is used for the proposed sensor, the strain sensitivity is independent of the length of the sensor head (PM-PCF). In the practical PM-PCF used in experiments, however, a shorter PM-PCF has a higher length dependence of the modal birefringence due to its imperfectness and nonuniformity of the internal structure, resulting in a higher length dependence of the strain sensitivity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1057-1060
• /
• 2001

By comparison of the experimental results in two systems of ZnO varistors, its appear that Sb$_2$O$_3$is the indispensable element for twinning in ZnO varistors, and the Zn$_{7}$Sb$_2$O$_{12}$ spinel acts as the nucleus to form twins. A1$_2$O$_3$is not the origin of twinning in ZnO varistor, but it was found that A1$_2$O$_3$could strengthen the twinning and form a deformation twinning by ZnA$_{12}$O$_4$-dragging and pinning effect. The inhibition ratios of grain growth and nonuniformity of two systems ZnO varistors increase with the increase of A1$_2$O$_3$content. The twins affect the inhibition of grain growth, the mechanism could be explained follow as : twins increase the mobility viscosity of ZnO grain and grain boundary, and drag ZnO grain and liquid grain boundary during the sintering, then the grain growth is inhibited, and the microstructure becomes more uniform.orm.m.

• 대한조선학회논문집
• /
• 제36권3호
• /
• pp.29-40
• /
• 1999

캐비테이션이 발생하지 않는 프로펠러의 정상 및 비정상 하중에 의해 음장에 유기되는 소음을 지배하는 음파 방정식에 대한 주파수 영역에서의 수치 해석법을 정립하였다. 본 연구를 통하여 음압 스펙트럼에서 날개 통과 진동수 배수의 소음만이 발생한다는 것을 보였으며, 이때 적용되는 파수는 반류의 불균일성에 기인하는 조화성분과 프로펠러의 회전에 의해 발생되는 Doppler 효과가 고려되도록 표현되어야 함을 보였다. 특정 전진속도에서 하중이 없도록 설계된 날개수가 2인 모형 프로펠러에 대한 이론적 추정과 실험결과를 비교함으로써, 정상상태인 경우 날개 두께 효과가 매우 중요하나, 비정상상태에서는 날개하중의 변화에 의한 소음의 영향이 커서 정상상태에 비하여 두께효과가 비교적 적게 기여함을 알 수 있었다.

• 대한조선학회논문집
• /
• 제42권1호
• /
• pp.1-9
• /
• 2005

Waterjet propulsion is widely used to thrust high speed marine vessels in excess of 30-35 knots by virtue of the high propulsive efficiency, good maneuverability, and less cavitation. From the aspect of power loss, approximately $7-9\%$ of the total power is lost in intake duct due to the flow separation, nonuniformity, etc. Thus, detail understanding of flow phenomena occurring within intake duct is essential to reduce the power loss, as well as noise and vibration. The present work solved 30 incompressible RANS equations to provide complicated viscous flow features of intake duct. The numerical results were compared with experiments and good agreements were obtained for three jet velocity ratios.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.125-128
• /
• 2004

Chemical Mechanical Polishing(CMP) in semiconductor production is characterized its output property by Removal Rate(RR) and Non-Uniformity(NU). Some Previous works shows that RR is determined by production of pressure and velocity and NC is also largely affected by velocity of flow-field during CMP. This study is about the direct measurement of velocity of slurry during CMP and reconstruction whole flow-field by Particle Image Velocimetry(PIV) Techniques. Typical PIV system is tuned adequately for inspecting CMP and Slurry Flow-field is measured by changing both Pad RPM and Carrier RPM. The results show that velocity is majorly determined not by Carrier RPM, but by Pad RPM.