• Journal of Aerospace System Engineering
• /
• v.16 no.1
• /
• pp.12-16
• /
• 2022

Currently, Induction welding is attracting attention as a non-contact, clean and fast welding process. However, since thermoplastic resins are not affected by electromagnetic fields, induction welding requires a heating element called a susceptor. Researches are being conducted with the aim of achieving high-quality bonding, however, the factor of a heating element is an issue, hence the need to set a standard. Specimen fabrication and testing are conducted according to ASTM D5868. In this study, we propose that the evaluation criteria be judged on the basis of three factors; the condition of the welded joint surface, void content, and lap shear strength. Since the adhesive surface to be welded melts and solidifies as it cools, rapid temperature changes can generate pores. In addition, if the heating is not uniform, it is difficult to expect the desire performance. Using PA6 (CF 30%) thermoplastic, susceptor fabrication, induction welding and performance verification were conducted.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.1
• /
• pp.41-47
• /
• 1984

Increase of the requirements on quality of welded structures necessitates the improvement of known inspection methods and the introduction of progressive new techniques. Non-destructive methods are the most advanced, but there are considerable difficulties in using the methods of radiography with electromagnetic rays and ultrasonic testing in the inspection of dissimilar metal friction welds, because their physical and mechanical properties are changed very rapidly at the interface. The values of simple mechanical test for dissimilar metal friction welds have always been dubious, as the strength of the bond is often greater than that of the softer materials being jointed. Thus, in this paper some conventional mechanical testing methods are examined in an attempt to determine a technique for dissimilar metal friction welds, which will give a reliable quantitative indication of the weld quality. From the considered static and dynamic testing methods the impact bending test on unnotched and notched specimens are the most sensitive to find out the small joining defects in the interface.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.69-77
• /
• 1996

This study aims to analyze the S. I. F. K value upon Mode I cracks in a finite-width plate of varying thickness, which is expressed in terms of width ratio ($\omega$), thickness ratio ($\beta$) and non-dimensional crack length (λ) by using the 2-dimensional finite element method. Then, by comparing the effectiveness of the results obtained by the two finite element methods, it is seen that the 2-dimensional finite element method can be used in order to analyse the S. I. F. K values upon a various thickness model. A model is developed in order to analyze the effects of initial residual stress upon the fatigue crack growth behavior in various thickness welded specimens. In this model, crack growth rate da/dN appears to be come small as the thickness ratio with the same ΔK is increased. Also, in the initial step, as ΔK is increased with crack growth rate is decreased and then increased because the repeated compressive residual stress retards crack growth rate.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.381-388
• /
• 1999

The existing methods for installation of long steel pipe pile have some uneconomical problems such as increase of installation cost and period due to the welding of two piles and removal of soil plug, and decrease of driving efficiency due to the increase of driving resistance by time effect during the welding of piles and removal of soil plug, etc. Thus, in this study, new installation method for long steel pipe pile is suggested to work out the existing problems, and calibration chamber tests are peformed to investigate both driving and economical efficiency for the suggested method. The test results showed that the new installation method has increase bearing capacity as well as reduce installation cost and period for long steel pipe piles as compared with existing methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.49-59
• /
• 2005

This paper describes a development of the extrusion process and estimation of the weldability for multi cell tubes used to cooling system of automobiles. A study on extrusion process is performed through the 3D FE simulation in non-steady state and extrusion experimentation. Also, nano-indentation test is employed to estimate the weldability of tubes. Especially, An evaluation of the weldability using the nano-indentation is accomplished as compared with nano-hardness in welded part and in the others. Finally, the pattern of the mandrel defection is investigated according to shapes of the porthole and/or chamber.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.766-769
• /
• 2004

This paper presents 3D nonlinear analysis considering the slip of composite section as well as the static load tests of PSC-Steel hybrid girders. According to the slip modulus, the nonlinear analysis shows that the behavior of hybrid girders could be divided into three parts as full-composite, partial-composite and non-composite. However, the experimental results show that the PSC-Steel hybrid girders with shear connectors take the part of partial composite action in ultimate load stage. In addition, the load test results give that stud shear connectors and welded reinforcements have contributed to improve the ultimate strength of hybrid girders for about $20\%$.

• Journal of the Korean Society for Railway
• /
• v.7 no.2
• /
• pp.125-129
• /
• 2004

This study investigates the fatigue lift estimation of butt weld specimen for the railway vehicle by examining butt weld bead profiles. The butt weld beads, which are welded by semi-robot method, have non-uniform bead profiles described by $\theta$, p and h. The stress concentration factors, K$\_$t/, are changed by different $\theta$, p and h from 1.395 to 2.863. Hence, the sensitivity of K$\_$k/ is changed by each $\theta$, p and h. As $\theta$ becomes lower and p and h become higher, K$\_$t/ increases. The fatigue life can be estimated very closely for the AAY specimens without residual stress using only butt weld bead profiles. But, for the AAN specimens with residual stress, the fatigue life must be estimated by considering both the weld bead profiles and the residual stress data.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.100-102
• /
• 2004

인장강도 600MPa 이상을 가지는 TRIP형 고장력 강판인 60TR-R과 석출경화형 합금인 CHSP60C는 자동차용 소재로 주목을 받고 있다. 또한 레이저 용접은 열 변형이 적고 비드 외관이 미려할 뿐만 아니라 연속 및 고속 용접이 가능하여 생산성 및 정밀성, 안정성이 높아 자동차조립 및 부품 제조공정에 적용되고 있다. (중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.8 s.239
• /
• pp.1043-1050
• /
• 2005

Condenser tube is a component of the heat exchanger in automobile and air conditioning apparatus. It is generally made from the 1000 or 3000 series Al alloys that have good heat efficiency. In the case of 3000 series, these have high strength and hardness but have the disadvantage of low extruability. The development of extruding process in condenser tube with 3000 series Al alloys is studied in this paper. A study on extrusion process is performed through the 3D FE simulation in non-steady state and extrusion experimentation. Also, nano-indentation test is employed to estimate the weldability of tubes. Especially, An evaluation of the weldability using the nano-indentation is accomplished as compared with nano-hardness of welded part and the others in cross-section of tube.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2002.05a
• /
• pp.25-27
• /
• 2002

Most of automotive companies make use of spot welding in order to assemble car body. Even though spot welding has been developed for last 60 years, there were some limitations in upgrading production line. Laser welding has advantages In productivity and degree of freedom in design. Thanks to fast speed, we can reduce body assembly line by 80%. Also with non-contact & one-side approach, it is possible to design various car body structures. New project launched the laser welding technology in mass production has started in 1999. In this paper, a new type of cur named 'next generation vehicle (NGV)' is introduced. The car body of NGV is welded with 4㎾ Nd: YAG laser.