• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.442-450
• /
• 2006

This paper describes the new modal analysis method to detect the presence of the breathing crack in a general rotor system with disk asymmetry and stator anisotropy. It is proposed that the modal analysis using directional frequency response functions (dFRFs), which, accounting for the directivity in modes, clears the heavily over-lapping of other harmonics occurring from non-isotropic properties in addition to those due to crack, can provide an effective method to detect the modes by a crack. The simulations from the simple general rotor model show that the r-dFRFs (reverse dFRFs) for asymmetry confirms a good indicator of the presence of the breathing crack and the instability is primarily influenced by the shaft asymmetry than the breathing crack.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1998년도 학술발표회 발표논문집
• /
• pp.124-129
• /
• 1998

The ultrasonic pulse measurements can be used to detect the development of cracks in concrete structures and to check deterioration due to frost or chemical action. An estimate of the depth of a visible crack at the surface can be obtained by measuring the transit times that across the crack for two different arrangements of the transducers placed on the surface. In this paper, the concrete cracks that artificially introduced crack of width 1, 2mm and depth 20, 40, 60, 80mm were measured by Tc-To, Direct and Indirect Method. The test results indicate that the Tc-To Method is the most useful in measuring crack of concrete structures. And the crack depth calculated by the Direct and Indirect Method is shown bigger than artificially introduced real crack depth.

• Journal of Mechanical Science and Technology
• /
• 제16권2호
• /
• pp.182-191
• /
• 2002

The reliable stress intensity factor analysis is required for fracture mechanics design or safety evaluation of mechanical joints at which cracks often initiate and grow. It has been reported that cracks in mechanical joints usually nucleate as corner cracks at the faying surface of joints and grow as elliptical arc through cracks. In this paper, three dimensional finite element analyses are performed for elliptical arc through cracks in mechanical joints. Thereafter stress intensity factors along elliptical crack front including two surface points are determined by the virtual crack closure technique. Virtual crack closure technique is a method to calculate stress intensity factor using the finite element analysis and can be applied to non-orthogonal mesh. As a result, the effects of clearance on the stress intensity factor are investigated and crack shape are then predicted.

• 터널과지하공간
• /
• 제10권3호
• /
• pp.301-308
• /
• 2000

균열모형을 이용하여 압축 하중하에 있는 암석의 비선형 거동을 예측하는 것은 가능하다. 암석내의 균열의 성장은 암석의 이방성을 가져오며, 이러한 이방성의 정도는 단성계수의 변화로 표현될 수 있다. 본 연구에서는 균열의 성장에 따른 탄성계수의 변화를 이론적인 균열모형을 통해 예측하고, 이를 탄성파 속도 시험을 통해 구한 탄성계수와의 비교를 수행하였다. 또한, 균열모형에 사용되는 초기 암석내 존재하는 균열에 대한 정보는 암석표면의 이미지를 분석하여 구하였다.

• 한국암반공학회:학술대회논문집
• /
• 한국암반공학회 2000년도 암반공학문제의 수치해석(Numerical Analysis in Rock Engineering Problems)
• /
• pp.47-55
• /
• 2000

균열모형을 이용하여 압축 하중하에 있는 암석의 비선형 거동을 예측하는 것은 가능하다. 암석내의 균열의 성장은 암석의 이방성을 가져오며 이러한 이방성의 정도는 탄성계수의 변화로 표현될 수 있다. 본 연구에서는 균열의 성장에 따른 탄성계수의 변화를 이론적인 균열모형을 통해 예측하고, 이를 탄성파 속도 시험을 통해 구한 탄성계수와의 비교를 수행하였다. 또한, 균열모형에 사용되는 초기 암석내 존재하는 균열에 대한 정보는 암석표면의 이미지를 분석하여 구하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.123-128
• /
• 2000

A cracked-plate with a patch bonded on one side is treated with a crack-bridging model: assuming continuous distribution of springs acting between crack surfaces. the approximate weight function was introduced to obtain the stress intensity factor of patched crack subjected to residual stress or non-uniform stress. The stress intensity factors for the partially patched crack within finite plate or the patched crack initiated from a notch were successfully obtained by numerical calculation.

• 한국해양공학회지
• /
• 제18권6호
• /
• pp.91-95
• /
• 2004

In this study, to investigate the effects of shot peening on crack growth behavior, crack growth tests are conducted on spring steels and shot peened cracks. The probabilistic crack growth equation, which can represemt the sigmoidal crack growth behavior as recently reported by Kim and Shim, is used to evaluate the experimental results. The results show that fatigue cracks grows slower in the shot peened specimen than in the unpeened and, due to the compressive residual stress occurring on the specimen surface. In the case of the shot peened specimen, the initial stress intensity factor range and the fracture toughness is higher than the non-peened specimen because the compressive residual stress affects crack growth and fracture of the specimen.

• Structural Engineering and Mechanics
• /
• 제7권6호
• /
• pp.575-588
• /
• 1999

A boundary element method is applied to the analysis of crack trajectory in materials with complex microstructure, such as discontinuously reinforced composite materials, and systems subjected to complex loading, such as indentation. The path followed by the crack(s) has non-trivial geometry. A study of the stress intensity factors and fracture toughness of such systems must therefore be accompanied by an analysis of crack trajectory. The simulation is achieved using a dual boundary integral method in planar problems, and a single boundary integral method coupled with substructuring in axisymmetric problems. The direction of crack propagation is determined using the maximum mechanical energy release rate criterion. The method is demonstrated by application to (i) a composite material composed of components having the elastic properties of aluminium (matrix) and silicon carbide (reinforcement), and (ii) analysis of contact damage induced by the action of an indenter on brittle materials. The chief advantage of the method is the ease with which problems having complex geometry or loading (giving rise to complex crack trajectories) can be treated.

• Structural Engineering and Mechanics
• /
• 제70권3호
• /
• pp.279-287
• /
• 2019

This paper intends to introduce a near-tip grid refinement and to explore its usefulness in the crack analysis by the natural element method (NEM). As a sort of local h-refinement in FEM, a NEM grid is locally refined around the crack tip showing the high stress singularity. This local grid refinement is completed in two steps in which grid points are added and Delaunay triangles sharing the crack tip node are divided. A plane-state plate with symmetric edge cracks is simulated to validate the proposed local grid refinement and to examine its usefulness in the crack analysis. The crack analysis is also simulated using a uniform NEM grid for the sake of comparison. The near-tip stress distributions and SIFs that are obtained using a near-tip refined NEM grid are compared with the exact values and those obtained using uniform NEM grid. The convergence rates of global relative error to the total number of grid points between the refined and non-refined NEM grids are also compared.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.88-94
• /
• 2006

The compressive residual stress, which is induced by shot peening process, has the effect of increasing the intrinsic fatigue strength of surface and therefore would be beneficial in reducing the probability of fatigue damage. However, the effect of shot peening in corrosion environment was not known. In this study, investigated is the effect of shot peening on corrosion fatigue crack growth of SAE 5155 steel immersed in 6% $FeCl_3$ solution and corrosion characteristics with considering fracture mechanics. The results of the experimental study corrosion fatigue characteristics of SAE 5155 are as follows; the fatigue crack growth rate of the shot peening material was lower than that of the non-peening material. And fatigue life shows more improvement in the shot peening material than in non-peening material. This is due to the compressive residual stress of surface increases resistance of corrosion fatigue crack propagation. It is assumed that the shot peening process improve corrosive resistance and mechanical property.