• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.2
• /
• pp.129-144
• /
• 2010

The earth pressure acting on the vertical shaft is less than that acting on the retaining wall due to three dimensional arching effect. Thus, it might be essential to estimate the earth pressure actually acting on the shaft when designing the vertical shaft. In this paper, large-sized model tests were conducted as Part II of companion papers to verify the newly suggested earth pressure equation proposed by Kim et al. (2009: Part I of companion papers) that can be used when designing the vertical shaft in cohesionless soils as well as in c-$\phi$ soils and multi-layered soils. The newly developed model test apparatus was designed to be able to simulate staged shaft excavation. Model tests were performed by varying the radius of vertical shaft in dry soil. Moreover, tests on c-$\phi$ soils and on multi-layered soils were also performed; in order to induce apparent cohesion to the cohesionless soil, we add some water to the dry soil to make the soil partially-saturated before depositing by raining method. Experimental results showed a load transfer from excavated ground to non-excavated zone below dredging level due to arching effect when simulating staged excavation. It was also found that measured earth pressure was far smaller than estimated if excavation is done at once; the final earth pressure measured after performing staged excavation was larger and matched with that estimated from the newly proposed equation. Measured results in c-$\phi$ soils and in multi-layered soils showed reduction in earth pressures due to apparent cohesion effect and showed good matches with analytical results.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.346-361
• /
• 2013

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2012. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. The conclusions are as follows : (1) The research works on thermal and fluid engineering have been reviewed as groups of fluid machinery, pipes and valves, fuel cells and power plants, ground-coupled heat pumps, and general heat and mass transfer systems. Research issues are mainly focused on new and renewable energy systems, such as fuel cells, ocean thermal energy conversion power plants, and ground-coupled heat pump systems. (2) Research works on the heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer, and industrial heat exchangers. Researches on heat transfer characteristics included the results for natural convection in a square enclosure with two hot circular cylinders, non-uniform grooved tube considering tube expansion, single-tube annular baffle system, broadcasting LED light with ion wind generator, mechanical property and microstructure of SA213 P92 boiler pipe steel, and flat plate using multiple tripping wires. In the area of pool boiling and condensing heat transfer, researches on the design of a micro-channel heat exchanger for a heat pump, numerical simulation of a heat pump evaporator considering the pressure drop in the distributor and capillary tubes, critical heat flux on a thermoexcel-E enhanced surface, and the performance of a fin-and-tube condenser with non-uniform air distribution and different tube types were actively carried out. In the area of industrial heat exchangers, researches on a plate heat exchanger type dehumidifier, fin-tube heat exchanger, an electric circuit transient analogy model in a vertical closed loop ground heat exchanger, heat transfer characteristics of a double skin window for plant factory, a regenerative heat exchanger depending on its porous structure, and various types of plate heat exchangers were performed. (3) In the field of refrigeration, various studies were executed to improve refrigeration system performance, and to evaluate the applicability of alternative refrigerants and new components. Various topics were presented in the area of refrigeration cycle. Research issues mainly focused on the enhancement of the system performance. In the alternative refrigerant area, studies on CO2, R32/R152a mixture, and R1234yf were performed. Studies on the design and performance analysis of various compressors and evaporator were executed. (4) In building mechanical system research fields, twenty-nine studies were conducted to achieve effective design of mechanical systems, and also to maximize the energy efficiency of buildings. The topics of the studies included heating and cooling, HVAC system, ventilation, renewable energy systems, and lighting systems in buildings. New designs and performance tests using numerical methods and experiments provide useful information and key data, which can improve the energy efficiency of buildings. (5) In the fields of the architectural environment, studies for various purposes, such as indoor environment, building energy, and renewable energy were performed. In particular, building energy-related researches and renewable energy systems have been mainly studied, reflecting interests in global climate change, and efforts to reduce building energy consumption by government and architectural specialists. In addition, many researches have been conducted regarding indoor environments.

• Korean Journal of Plant Taxonomy
• /
• v.31 no.3
• /
• pp.267-282
• /
• 2001

To examine the leaf epidermal microstructure of three genera (Scopolia s.s., Anisodus, AtroPanthe, including Przewalskia as an outgroup) in the genera Scopolia Jacq. s.l., leaves of 10 species (37 specimens) were investigated by the light microscopy (LM) and scanning electron microscopy (SEM). The stomata of studied taxa were 'amphistomatic type' and the size (guard cell) range was $18-64{\times}11-48{\mu}m$. The size of stomata is slightly differed from between the taxa; the smallest size of stomata were found in the monotypic genus, Przewalskia ($24-27{\times}16-17{\mu}m$), on the other hand the largest one was found in Anisodus carniolicoides ($62-64{\times}43-48{\mu}m$). The stomatal complex was mostly anomocytic (in Scopolia s.s., Anisodus taxa : A. luridus, A. carniolicoides, A. acutangulus) and sometimes anisocytic (in Anisodus tanguticus, Przewalskia, Atropanthe). The stomata is mostly crescent in shape, but rarely circular, especially in Przewalskia tangutica. The shapes of epidermal cells are similar in both adaxial and abaxial sides, and mostly undulate/sinuate polygonal anticlinal wall, but rarely arched in Przewalskia tangutica. The epicuticular wax was not well developed in most studied taxa, except Anisodus tanguticus which is well developed cuticular striae around the stomatal complex. The elongate-headed glandular trichomes were found in Scopolia s.s. and Przewalskia. While the taxa of Anisodus and Atropanthe have not any trichomes (i. e., glabrous), except Anisodus luridus, which has simple or sometimes branched (dendritic- type) non-glandular trichome. Finally, the systematic and ecological significance of the leaf micromorphological features (stomata complex, trichome, etc.) in identification and elucidation of Scopolia s.l. including Przewalskia, especially between or within the genera including among the species is also discussed.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.2
• /
• pp.94-108
• /
• 2010

The purpose of this study is to provide data for the restoration of 'Yongyun(龍淵)' and 'Hwahongmun(華虹門)' through an investigation of the vicinity of their original landscapes at the time of construction of Hwaseong in Suwon and through tracing the transformative process of the environments of this vicinity. The results are as follows; As identified by 'Yongyunjung(龍淵亭)' and 'Yongdugak(龍頭閣)', other names of Yongyun, 'Banghwasuryujung(訪花隨柳亭)', which was built on 'Yongduam', is a facility whose place identity is highlighted with a sense of unity with Yongyun. The south lakefront of Yongyun, bordering Banghwasuryujung, has boundaries that make the best use of the natural geographical features of Yongduam while the current circumference of Yongyun is comparatively shorter than its original state. The size of 'Joongdo(中島)', however, seems to be an example of apparent over-design complement and reorganize 'Joongdo', which had been restored larger than its original state at the time of restoration in the 1970s. The depth of 'Yongyun' was created to be lower than the actual depth, without consideration for its initial depth, as soil was accumulated through continuous flooding after it was created. It is assumed that the original drains which were installed about 10m inside the lake were created facing the stream. As regards the planting environment, a circular planting of willows was made in the outskirts of 'Yongyun', except the 'Yongduam' which is a pure forest, and a mix of 'Pinus densiflora', shrubbery and deciduous broad leaf trees was planted in 'Joongdo'. Of the plants growing in the area of this study, plant species introduced to Korea after Hwaseong was constructed are found, most of which provide interest and attraction. The old pine trees growing in a group once grew in the castle areas of the vicinity even in the 1920s, the period of Japanese occupation, but they disappeared from the area in the aftermath of subsequent urban development and the Korean War. Although restored to the site, the number and space taken up by these trees are insignificant compared to those of the original environment. On the basis of these results, the following is considered necessary for the true restoration of the vicinity of 'Yongyun' and 'Hwahongmun': First, the grounds of 'Yongyun' should be dredged deeply enough to expose the bedrock and should be recreated in the rough outline of a half moon by extension to the southwest toward 'Yongduam' and 'Hwahongmun', and the size of 'Joongdo' should be significantly reduced. Secondly, considering that most plant species, except the pine trees and wild trees in 'Yongduam', are non-native plants introduced in order to provide such attractions such as the appreciation of scenic areas, they should be replaced with native species, mainly with the pine trees which were utilized during the construction of Hwaseong. The weeping willows planted in the 'middle-island' should be relocated to the outskirts of 'Yongyun', and replaced with pine trees as the major trees and maple trees or deciduous broadleaf trees to fill in the gaps. Thirdly, exotic species such as the 'Pinus rigida' planted in a group around 'Banghwasuryujung' and 'Bugammun' and 'Pinus strobus' planted in the vicinity of Hwahongmun' should be removed.

• Journal of Gastric Cancer
• /
• v.8 no.1
• /
• pp.27-34
• /
• 2008

Purpose: Many recent studies have reported on the feasibility and usefulness of laparoscopy assisted distal gastrectomy (LADG) for treating early gastric cancer. On the other hand, there has been few reports about laparoscopy assisted total gastrectomy (LATG) because upper located gastric cancer is relatively rare and the surgical technique is more difficult than that for LADG, We now present our procedure and results of performing LATG for the gastric cancer located in the upper or middle portion of the stomach. Materials and Methods: From Jan 2005 to Sep 2007, 96 patients underwent LATG by four surgeons at the Asan Medical Center, Seoul, Korea. Among them, 48 consecutive patients who were operated on by asingle surgeon were analyzed with respect to the clinicopathological features, the surgical results and the postoperative courses with using the prospectively collected laparoscopy surgery data. Results: There was no conversion to open surgery during LATG. For all the reconstructions, Roux-en Y esophago-jejunostomy and D1+beta lymphadenectomy were the standard procedures. The mean operation time was $212{\pm}67$ minutes. The mean total number of retrieved lymph nodes was $28.9{\pm}10.54$ (range: $12{\sim}64$) and all the patients had a clear proximal resection margin in their final pathologic reports. The mean time to passing gas, first oral feeding and discharge from the hospital was 2.98, 3.67 and 7.08 days, respectively. There were 5 surgical complications and 2 non-surgical complications for 5 (10.4%) patients, and there was no mortality. None of the patients needed operation because of complications and they recovered with conservative treatments. The mean operation time remained constant after 20 cases and so a learning curve was present. The morbidity rate was not different between the two periods, but the postoperative course was significantly better after the learning curve. Analysis of the factors contributing to the postoperative morbidity, with using logistic regression analysis, showed that the 8MI is the only contributing factor forpostoperative complications (P=0.029, HR=2.513, 95% CI=1.097-5.755). Conclusions: LATG with regional lymph node dissection for upper and middle early gastric cancer is considered to be a safe, feasible method that showed an excellent postoperative course and acceptable morbidity. BMI should be considered in the patient selection at the beginning period because of the impact of the BMI on the postoperative morbidity.

• International Journal of Highway Engineering
• /
• v.8 no.2 s.28
• /
• pp.63-74
• /
• 2006

During the construction of circular underground pipe, the non-proper compaction along the pipe and the decrease of compaction efficiency have been the main problems to induce the failure of underground pipe or facility. The use of CLSM (controlled low strength materials) should be one of the possible applications to overcome those problems. In this research, the full-scaled field test and the numeric analysis using PENTAGON-3D FEM program were carried out for three different cases on the change of backfill materials, including the common sand, the soil from construction site, and the CLSM. From the full-scaled test in field, the use of in-situ CLSM as backfill materials reduced the vertical and lateral deformation of the pipe, as well as the deformation of the ground surface. The main reason for reducing the deformation would be the characteristics of the CLSM, especially self-leveling and self-hardening properties. The measured earth pressure at the surround of the corrugated pipe using the CLSM backfills was the smaller than the other cases, and the absolute value was almost zero. Judging from the full-scaled field test and FEM analysis, the use of CLSM as backfill materials should be one of the best choices reducing the failure of the underground pipes.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.18 no.1
• /
• pp.62-68
• /
• 2014

Purpose: After I-131 therapy, SPECT/CT is useful in identifying location of thyroid remnants and metastasis of thyroid cancers. An excessive uptake of thyroid leads to a ringing artifact in the SPECT images. The aim of this study is to investigate and suggest a proper post filters to remove ringing artifact and produce better image quality. Materials and Methods: A low-cost, customized thyroid-mimicking phantom, consisting of an acrylic bottle and a hollow sphere was used for SPECT/CT Discovery (GE Healthcare, USA). It was filled with I-131 solution. The ratio of hollow sphere to background were varied as 50:1, 200:1, 1000:1 and 4000:1. Acquired images were reconstructed by OSEM (2 iterations, 10 subsets) with and without Evolution (resolution recovery correction, GE). Three different post-filters were applied; Butterworth (cut off: 0.38 to 0.58 with intervals of 0.05), Hanning (cut off: 0.8 to 1 with intervals of 0.05) and Gaussian (FWHM: 3 to 5 with intervals of 0.5) filters. Contrast, background variability, air area variability, and full width half maximum (FWHM) were compared. Results: Higher contrasts were obtained from the SPECT images with Evolution than without Evolution. In the case of images without Evolution, image distortion such as star artifact was generated. For all sphere-to-background ratio, the Butterworth filter showed better constrasts and FWHMs than other two filters, but the ringing artifact was still generated in all studies except 50:1 and it was decreased as cutoff value was increased. The ringing artifact didn't appear with Hanning and Gaussian filters at all studies, however constrats and FWHMs with Gaussian was worse than Hanning filter. For the images having ringing artifacts, the background variability and air area variability were increased. Conclusion: In this study, we suggested that it is desirable to use Hanning filter when the ringing artifact is generated and to use Butterworth filter when ringing artifact is not generated in I-131 SPECT.

• Geophysics and Geophysical Exploration
• /
• v.21 no.3
• /
• pp.150-161
• /
• 2018

Recently, unmanned aircraft EM (electromagnetic) survey based on ICT (Information and Communication Technology) has been widely utilized because of the efficiency in regional survey. We performed the theoretical study on the unmanned airship EM system developed by KIGAM (Korea Institute of Geoscience and Mineral resources) as part of the practical application of unmanned aircraft EM survey. Since this system has different configurations of transmitting and receiving loops compared to the conventional aircraft EM systems, a new technique is required for the appropriate interpretation of measured responses. Therefore, we proposed a method to calculate the EM field for the arbitrary shaped transmitter and verified its validity through the comparison with analytic solution for circular loop. In addition, to simulate the magnetic responses by three-dimensionally (3D) distributed anomalies, we have adapted our algorithm to 3D frequency-domain EM modeling algorithm based on the edge-FEM (finite element method). Though the analysis on magnetic field responses from a subsurface anomaly, it was found that the response decreases as the depth of the anomaly increases or the flight altitude increases. Also, it was confirmed that the response became smaller as the resistivity of the anomaly increases. However, a nonlinear trend of the out-of-phase component is shown depending on the depth of the anomaly and the used frequency, that makes it difficult to apply simple analysis based on the mapping of the magnitude of the responses and can cause the non-uniqueness problem in calculating the apparent resistivity. Thus, it is a prerequisite to analyze the appropriate frequency band and flight altitude considering the purpose of the survey and the site conditions when conducting a survey using the unmanned aircraft EM system.

• Journal of Korean Academy of Nursing
• /
• v.25 no.3
• /
• pp.597-607
• /
• 1995

1960년대 이후 인공호흡기(mechanical ventilator)의 보급과 최근 의료과학의 발달, 간호의 질적 향상의 결과로 저체중출생아를 포함한 고위험 신생아의 생존율이 높아져왔다. 호흡장애증후군(RDS)은 일차적으로 폐포의 완전한 확장을 위해 필요한 계면활성물질(surfactant)의 부족, 미발달된 심폐기능에 의한 병리적 현상으로 저체중아의 가장 큰 원인이 되어왔다. RDS로 인해 인공호흡기에 의존해 있는 저체중아의 경우 적절한 산소공급과 이를 위한 호흡의 유지는 치료의 가장 큰 핵심이 되며, 이를 위한 기관내 흑은 비인두 흡인 (nasopharyngeal suction)은 신생아 중환자실(NICU)의 가장 중요한 간호행위가 되어왔다. 인공호흡기를 위한 기관삽관은 그 자체가 기도의 성모운동을 방해하고 기침반사를 억제시켜 폐 분비물의 효과적 배출을 억제하며, 특히 저체중아의 경우 조산과 관련하여 미발달된 흥곽운등과 심폐기능은 폐분비물의 이동을 저해하는 요소이다. 따라서 기도내의 분비물의 이동을 효과적으로 하여 흡인 시에 최대한의 효과를 돕기 위해 흥곽 물리요법(chest physiotheraphy : CPT)의 한 형태인 흉곽진동법 (Chest Vibration : CV)가 행해져 왔다. 그러나 저체중아를 위한CV의 임상적 적용은 그 대상의 생리적 특성, CV의 적용부위(site)와 기간(duration)에 대한 과학적 근거 없이 만성감염이나 폐질환을 가진 성인이나 cystic fibrosis환자를 위한 CV protocol을 무분별하게 채택하여 저체중아에게 행하여져 왔다 이에 본 연구자는 저체중아에 대한 CV의 안전성을 평가하고, 이에 기초하여 저체중아에게 바람직한CV의 형태를 알아보고자 본 연구를 시작하였다. 연구설계는 CV의 안전성을 평가하기 위한 실험연구이다. CV의 안전성은 RDS치료의 가장 일차적 목표인 oxygenation변화에 의해 평가될 수 있으므로, 본 실험 연구에서는 Pulse oximeter에 의해 계속적으로 측정된 산소포화 변화(oxygen saturation change)를 측정하였다. 실험대상은 미국동부에 위치한 대학병원의 NICU에 입원하여 RDS와 관련된 호흡장애로 인공호흡기에 의존해 있는 10명의 저체중아였다. 인공호흡기에 의존된 모든 저체중아는 Pulse oximeter와 심폐기능 측정기(cardiopulmonary monitor)에 의해 산소공급과 호흡상태가 계속 측정되고 있었다. 실험대상의 평균 출생시 몸무게는 평균 1,3050gm(SD=580.6)이었고, 임신월령 은 평균 28.6주(SD=3.1)였다. RDS가 그들의 일차적 진단명이었고, 그중 4명은 pneumonia, atelectasis의 합병증을 가지고 있었다. 10명중 6명은 intermittent mandatory ventilation(IMV)의 형태로, 4명은 continuous positive airway pressure(CPAP)의 형태로 인공호흡기에 의존되어 있었고 CV시의 FiO2는 평균 42.3(SD=21.2)였다. CV는 중환아용 소형진동기 (minivibrator)를 이용해 가각 10명 의 간호사에 의해 행하여 졌고, 최소 22초에서 최대 100초 동안 실시되었다. 50%의 간호사는 30초에서 40초간 CV를 실시하였으며, CV의 적용부위도, 전후 흉곽부위, 혹은 병변이 있는 좌 우측, 흑은 양쪽 흉벽 등으로 다양했고, 적용방법도 원형으로 돌려가며(circular motion), 혹은 아래에서 위로, 혹은 아무런 기준없이 간호사의 기호에 따라 다양하게 적용되었다. 산소포화의 변화는 CV가 행해지기 전.후로 5초동안 관찰되었다. 연구의 결과, 산소포화 변화는 비 모수통계(non parametric statistics)의 일종인 Matched Paired Wilcoxon test로 분석 한 결과 CV후에 3%의 감소를 보였다(P<.05). 저체중아에 있어 산소포화의 3%감소는 임상적으로 중요한 의미가 없다고 사료되어지며, 실제 흡인전의 과도호흡에 의해 CV를 행하기 이전의 산소공급수준으로 돌아 왔다. CV실시 기간과 산소포화와의 상관관계는 비 모수통계인 Spearman rho correlation coefficient를 이용하여 분석하였는데, 이 두 변수는 서로 관계가 없는 것으로 나타났다(P>.05) 또한 CV와 흡인 후에 각각의 간호사들에게 CV를 필요로 한 저체중아의 기준, 적용부위, 기간, 방법등에 대한 기준을 물었으나 대상의 특성에 따른 간호사정에 의존하기보다는 간호사 각자의 선호하는 방법이나 습관에 라 행하는 것으로 나타났다. 결론적으로 CV와 산소포화 변화와의 관계, NICU에서 관찰된 CV의 임상적 적용을 기초로 저체중아에게 안전한 CV protocol은 신생아용 소형 진동기를 이용하여, 양쪽 흉곽의 늑골하측 변연 부위(low lateral costal margin)에서 시작하여 흉골 중앙부위 방향으로 30초 동안 진동기를 적용하는 것이 좋은 것으로 나타났다. 이에 CV의 효과를 평가하기 위한 보다 과학적인 접근방법으로, CV와 흡인의 결과인 가래(sputum)에 대한 연구를 제언하는 바이다.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.38 no.4
• /
• pp.12-24
• /
• 2020

The purpose of this study is to analyze the influence of the water system on the location, spatial structure, and construction method of Hongju-eupseong, centering on Hongjumok-eupchi. During the Joseon Dynasty, the water system in Hongjumok-eupchi is composed of artificially constructed Seong-an Runnel and ponds based on a branch-shaped natural waterways flowing from south to north and west to east. Compiling the results of various literature records, excavations and analysis of map data, it can be seen that the water system has an important influence on the construction of Hongju-seong. Firstly, Hongju-seong from the Goryeo Dynasty to the late Joseon Dynasty is located using a circular shape of topographical structure and a small erosion basin formed on the inner side of the Hongseongcheon and Wolgyecheon streams without significant change in location. In particular, Wolgyecheon and Hongseongcheon are natural moats, which are harmonized with Sohyangcheon and riverside topographical structures, affecting the location and construction method of Hongju-seong, water related facilities, and the spatial structure of eupseong. It is understood that location characteristic of Hongju-seong reflects the urban location structure harmonized with waterways in ancient China and Korea. Secondly in harmony with the water system and topographic structure of Hongju-seong, it is an important factor in deciding the land use of the town, the arrangement of the town hall facilities and inducing various non-subsidiary measures such as the establishment of embankment forest with a secret function and the closure of the south gate. In addition, artificial drainage facilities such as Seongan runnel and ponds are being actively introduced from early on to protect the walls or towns from flooding of Wolgyecheon. Especially there were typical methods for protecting the walls from water damage such as the Joseon Dynasty stone castle structure that was integrated with saturn(soil wall) in the Goryeo Dynasty, retreating wall in the northern gate area in the late Joseon Dynasty, and the method of constructing wall using korean tile and stone floors between reinforced soil layers in the western and northern wall.