• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.605-611
• /
• 2000

Presented in this paper is a new method of identifying the critical speed of rotor-bearing systems without actually reaching at the critical speed itself. Using the method, it is not only possible to calculate the critical speed by measuring a series of rotor responses at much lower rotating speeds away from and without reaching at the critical speeds but also the damping ratio and eccentricity of the system can be identified at the same time. Two types of test rotors were tested on the Rotor Dynamics Test Facility at the Rotordynamics Lab., KIMM, and the theory has been confirmed experimentally. The method can be adopted to monitor changes of the dynamic characteristics of critical rotating machinery before and after overhauls, repairs, exchanges of various parts, or to detect trends of direction of subtle changes in the dynamic characteristic parameters over a long periods of time.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.643-648
• /
• 2000

The AFM is an imaging tool or a profiler with unprecedented 3-D resolution for various surface types. The AFM technology, however, leaves a lot of room for improvement due to its delicate and fragile probing mechanism. The distance between probe tip and sample surface must be maintained in below the nano meter level in order to measure the sample surface in Angstrom resolution. In this paper, the mode analysis of AFM system, modification based on the mode analysis are performed and finally the sample surface is measured by the home-built AFM.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.237-242
• /
• 2000

The areal recording density of HDD(Hard Disk Drive) has been increasing by about 60% a year. In order to achieve high areal density, less track pitch is expected and more servo bandwidth is required. Dual stage actuator and servo controller for HDD have been suggested for achieving high track density as a possible solution. Dual-loop servo system is generally classified into a two-input-two-output system, but if we use an estimator for a two-input-two-output system, it can be converted into two input one output system. Since we can't control the dual stage servo system by the classical method, it requires a special technique; for example, Parallel Loop System, Master-Slave Loop System, Decoupled Master-Slave Loop System, and Dual Feedback Loop System. In this paper, we performed experimental evaluations of several types of control algorithm. Further experiments will be made in the future.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.462-467
• /
• 2000

The aim of this study is to provide fundamental data for acoustic design by analyzing the room acoustic characteristics according to the PA system used in the school gymnasium. The measurements were carried out accordance with the ISO 3382. The sources used in this study were four types; omni-directional, centralized, distribution, the combination of centralized and distribution sound source system. Omni-directional system is recommended by ISO for the acoustic test and the others are installed on the wall, column and ceiling in the school gymnasium for sound reinforcement.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1994년도 FIFTH WESTERN PACIFIC REGIONAL ACOUSTICS CONFERENCE SEOUL KOREA
• /
• pp.668-673
• /
• 1994

The paper presents a simple method for calculating the sound exposure level (LAE) of helicopter noise. It is assumed that a helicopter is a nondirective point source and that A-weighted sound pressure level at an observation point can be expressed by an A-weighted power level and a simple function of the distance from the helicopter. We derived a formula for LAE by integrating the sound energy along a finite or an infinite flight segment. The values calculated form the formula agree well with the results of test flights in which three types of helicopters each were operated in three moving modes of approach, takeoff and level flyover.

• 로봇학회논문지
• /
• 제14권1호
• /
• pp.14-21
• /
• 2019

In the ground environment, mobile robot research uses sensors such as GPS and optical cameras to localize surrounding landmarks and to estimate the position of the robot. However, an underwater environment restricts the use of sensors such as optical cameras and GPS. Also, unlike the ground environment, it is difficult to make a continuous observation of landmarks for location estimation. So, in underwater research, artificial markers are installed to generate a strong and lasting landmark. When artificial markers are acquired with an underwater sonar sensor, different types of noise are caused in the underwater sonar image. This noise is one of the factors that reduces object detection performance. This paper aims to improve object detection performance through distortion and rotation augmentation of training data. Object detection is detected using a Faster R-CNN.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.320.2-320
• /
• 2002

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. A substantial portion of the PES is caused by disk vibration. This can be reduced by using a head gimbal assemblies (HGAs) that do not confine the slider movement to the vertical direction to disks, but allow movement to the radial direction of disks with respect to disk vibration. Several types of HGAs are proposed for such radial motion of the slider. (omitted)

• Asia pacific journal of information systems
• /
• 제31권3호
• /
• pp.335-357
• /
• 2021

As reproduction of images can be done with ease, copy detection has increasingly become important. In the duplication process, image modifications are likely to occur and some alterations are deliberate and can be viewed as attacks. A wide range of copy detection techniques has been proposed. In our study, content-based copy detection, which basically applies DCT-based features for images, namely, pixel values, edges, texture information and frequency-domain component distribution, is employed. Experiments are carried out to evaluate robustness and sensitivity of DCT-based features from attacks. As different types of DCT-based features hold different pieces of information, how features and attacks are related can be shown in their robustness and sensitivity. Rather than searching for proper features, use of robustness and sensitivity is proposed here to realize how the attacked features have changed when an image attack occurs. The experiments show that, out of ten attacks, the neural networks are able to detect seven attacks namely, Gaussian noise, S&P noise, Gamma correction (high), blurring, resizing (big), compression and rotation with mostly related to their sensitive features.

• 한국음향학회지
• /
• 제33권1호
• /
• pp.10-20
• /
• 2014

본 연구에서는 입수 충격에 의한 수중 순간 소음을 연구하기 위해, 황해에서 발사대를 이용하여 해상 실험을 진행하였다. 해상시험선인 청해호 우현상에서 발사대를 이용하여 실린더 몸체를 수직으로 발사하였으며, 이때 발생하는 소음을 하이드로폰으로 측정하였다. 실험에서는 원통형, 원뿔형, 반구형 두부 형상을 가진 3가지 종류의 실린더 몸체가 사용되었다. 측정된 신호는 시간적으로 확연하게 구분되어 3단계로 전시되었다 : (1) 초기 충돌 및 물체 진동단계, (2) 개방 공동 유동 단계, (3) 공동 붕괴 및 거품 진동 단계. 대부분의 경우, 거품 진동 단계의 파형이 초기 충돌 및 물체 진동 단계에 비해 우세하게 나타났다. 공동이 붕괴되기 시작하는 핀치 오프 시간은 0.18 ~ 0.2 s에 발생하였으며, 평균 거품 지속 시간은 0.9 ~ 1.3 s로 지속되었다. 입수 충격 소음은 100 Hz 이하의 대역에서 에너지가 집중되어 있었으며, 생성되는 소음은 두부 형상, 물체 질량, 발사 속도에 의해 영향을 받았다. 결과적으로, 거품 주파수에서 에너지 스펙트럼 밀도의 크기는 원통형, 원뿔형, 반구형 순으로 나타났으며, 동일 입수체에 대해서는 초기 에너지가 클수록 거품 주파수에서 에너지 스펙트럼 밀도가 크게 나타났다. 최종적으로, 버블이 폭발하는 물리적 현상을 기반으로 모의된 신호와 계측 값간 비교 결과 만족스러운 결론을 얻을 수 있었다.

• Journal of Preventive Medicine and Public Health
• /
• 제10권1호
• /
• pp.94-101
• /
• 1977

Noise pollution, both in the environment and in the workplace, has been recognized as a major health hazard -one that can impair not only a person's hearing but also his physical and mental well-being. As industrialization progresses, the prevalence rate of occupational diseases is increasing, especially hearing loss, which has the highest prevalence rate among the occupational diseases. The major cause of noise is the construction of various large industries without any regulation of noise sources. Therefor, we must establish an enactment to control mechanical noise sources. as soon as possible. For the purpose of controlling the noise source, we must have exact data about such things as the sound level, the frequency of the peak sound and the revolutions per minute (r.p.m.) of the machine (a measure of the power of its motor). This study was undertaken in order to define the noise characteristics, the power of the machine's motor, the change of the sound level and the peak sound as the r.p.m. increases, and the permissible exposure time. The sample size of this study was 74 machines at 11 plants in 6 industries. The results are as follows; 1. The breakdown of the types of mechanical noise noted was : 63.6% continuous normal sound, 26.9% intermittent sound, 4.7% continuous repeating sound and 4.6% impulsive sound. 2. With respect to the type of industry, the overall sound level was the highest in the mechanical industry, with $103.8{\pm}2.8dB(A)$, and lowest in the textile industry, with $89.2{\pm}1.43dB(A)$. 3. With respect to the type of machine, the highest sound level was 124 dB(A) caused by Gauzing(II), in the mechanical industry, and the lowest was 76 dB(A) caused by Attachment (Jup Chack) (I) in the timber industry. 4. The shortest permissible exposure time to Gauzing(II) in the mechanical industry was less than 15 minutes. 5. Among 74 machines, 68.2% of the peak sound was situated in the high frequency range (52.7% at 2 KHz, 4.1% at 4 KHz and 1.4% at 8 KHz). 41.8% of the peak sound was in the middle frequency range (4.1% at 250Hz, 14.8% at 500Hz and 22.9% at 1KHz). 6. If one machine had two motors or more, the peak sound was shifted to the low frequency range. 7. As the r.p.m. increased, the overall and peak sound levels were increased without any change of the frequency of the peak sound. 8. Whenever the machines had the same kind and the same r.p.m., the overall and peak sounds were changed by the physicochemical characteristics of the raw materials and the management.