• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.220-225
• /
• 2003

Recent issue of optical actuator is applying to mobile device. It leads actuator to become smaller than conventional type. This paper proposes the design of micro actuator plate spring and analysis of its vibration characteristic. Considering natural frequency of spindle motor, 1st and 2nd eigenfrequency of micro actuator must avoid its natural frequency. First, magnetic circuit is designed by using fine pattern coil and magnetic force is acquired by simulation program. Then, concept design is achieved by topology optimization. From concept design, micro actuator plate spring is embodied through DOE(design of experiment). Finally, considering vibration characteristic simultaneously, optimal plate spring design is determined by RSM(response surface method).

• 한국소음진동공학회논문집
• /
• 제24권12호
• /
• pp.943-947
• /
• 2014

Recently, a new method for reconstructing a forced nonlinear dynamic system has been proposed; specifically, the simultaneous reconstruction of its excitation as well as restoring characteristics of the system. The reconstruction was just theoretically shown to be possible by measuring the system's responses, based on newly introduced notions, a J-function and a zero-crossing time. However, numerically in the current paper, we are to reconstruct a linear system, i.e., we focus on numerical experiments to reconstruct both the excitation and the linear restoring characteristic of a linear forced oscillating system by using response data, based on the J-function and the zero-crossing time.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.187-192
• /
• 2012

Recently, KARI(Korea Aerospace Research Institute) has been developing a modern 11.5 m diameter four bladed bearingless main rotor system, and this rotor system can be used for 7,000 lb class helicopter. Flexbeam and torque tube can be considered as key structural components, and large elastic twist of flexbeam induced by pitch control motion of torque tube can influence the nonlinear aeroelastic behavior. In this paper, the dynamic characteristic analysis results of bearingless rotor system were presented. In order to construct a input model and validate the analysis procedures, calculated results using the comprehensive helicopter analysis program CAMRAD II were compared with the measured natural frequencies and lag damping data from small-scale wind tunnel test. Next, the analysis model was extended to a full-scale model, and the dynamic analysis results were presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.594-599
• /
• 2000

Two basic acoustic quantities, the characteristic impedances and the propagation constants, of the two different ultra lightweight concrete absorbers were examined with impedance tube method. A transmission loss was tested and compared with theoretical values. The results show that these kinds of sample have proper sound absorption and transmission loss capabilities. It means that they can be used in various fields where noise proof is needed.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권7호
• /
• pp.316-321
• /
• 2002

In this Paper, the channel characteristics of the medium voltage(22.9kV) power line to analysis the broadband power line communication in the frequency range up to 30MHz was measured. With the sideband electrical coupler in the operating frequency range from DC to 30MHz, we measured characteristic impedance, noise and attenuation of the medium voltage power line, and then characteristic impedance was measured at the state of unloaded medium voltage power line by Scattering parameter method of Vector Network Analyzer. As a measurement result, Channel impedance shows 100~380$\Omega$ at the less than 15MHz and 70~230$\Omega$ at the more than 15 MHz. Noise characteristics of power line shows -75dBm at 20MHz and Narrowband interference noise was from 3 MHz to 7MHz.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.263-270
• /
• 1997

For a cylinder in a uniform flow stream, sound is generated by the fluctuating pressure on the cylinder surface due to the vortex shedding behind the cylinder. It is known that the major parameters to predict the sound pressure are the characteristic length of the flow along the cylinder axis and the fluctuating lift coefficient. These parameters strongly depend on the Reynolds number and the yaw angle of the cylinder to the free stream. In this experimental study the effects of yaw on the flow parameters, and consequently on the generated sound are investigated. The surface pressure and the radiated sound are measured simultaneously for different yaw angles and showed that the reduced normal velocity component to the cylinder axis reduces the unsteady lift fluctuation which results in lowered sound press-are level, However, experimental result shows that "the cosine law" which uses the normal velocity component as a characteristic velocity for noise Generation from a yawed cylinder needs to be carefully reviewed. reviewed.

• 센서학회지
• /
• 제13권1호
• /
• pp.12-19
• /
• 2004

The tinnitus which is the one of the auditory disease is a phenomenon that the patients feel the sound in the ear or the head when there is no sound sources. There have been many therapies for this tinnitus so far, but it is known that the TRT (Tinnitus Retraining Therapy) is the most effective therapy. So we designed and developed the controllable white noise generator for TRT. It must be designed as small as possible for user's convenience, such as the ITE (In The Ear) type hearing aids. It used the thermal noise as the white noise source. And filter and tone control circuits are used at the end of the noise generation part to control the white noise characteristics. This link of the controllable circuits is used to change the white noise's characteristic for the various tinnitus patients' characteristic. we can confirm that the designed and implemented controllable white noise generator which is a ITE type operates properly by the experiments of filter and tone control circuit.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.646-649
• /
• 2008

This study deals with mechanism of relay operation and modeling of transfer function between impact force and sound pressure due to the impact force in order to reduce relay noise. A collision between a moving-contact and fix-contact produces impact noise. Therefore impact noise of relay is determined by not only excitation force but also transfer function from impact force to noise. In this study, we find mechanism of relay operation, make impact force model and measure characteristic of relay noise. And also we find transfer function of relay noise.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.269-274
• /
• 2007

With the importance of comfortable environment, research about noise reduction of construction is consisting much. If construction receives the input force, noise will be generated thereby. We must predict vibration and noise characteristic to reduce structured borne noise, and construction which become a basis of such research is plate. In order to predict the radiating noise from the vibrating surface. It is required to know the velocity distribution of vibration surface exactly. It is good to use bead for reducing vibration and noise of plate. In this study, we have analyzed structure-borne noise of plate with bead and compare with plate that there is no bead about equal exciting force.

• 한국소음진동공학회논문집
• /
• 제25권11호
• /
• pp.723-730
• /
• 2015

This paper investigated the noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time Fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.