• Corrosion Science and Technology
• /
• v.7 no.2
• /
• pp.92-98
• /
• 2008

This paper describes the experiments of the corrosion and the sliding tests of the nickel-based alloys for the gate valve seating materials used at high pressure and temperature. The general corrosion rates and IGC susceptibility are tested in pressurized water at 533 K and 575 K and in Strauss test solution. The sliding tests have been done in pressurized water at 293 k, 473 K and 573 k. The alloys containing above 10% chromium may have the anti-corrosion properties that could be applied to the valve seats for the power plants. The good sliding performance and the good pressure tightness are obtained when the disc specimens that have hardness 500 to 600 Hv combined with the seat specimens that have hardness 250 to 410 Hv containing about 40 percent of iron. The large size gate valves sliding tests have certified the test results. The anti-wear properties of the seat alloy and the anti-IGC susceptibility of the disc alloy could be improved by the addition of silicon and niobium, respectively.

• Journal of Surface Science and Engineering
• /
• v.13 no.4
• /
• pp.211-220
• /
• 1980

Internal stress of electrodeposited metals affect physical and mechanical characteristics of deposits. Internal stress of nickel deposits was reviewed intensively. Important outcomes are as follows. Substrate have an important effect on internal stress of electrodeposit. Origin of its internal stress could be explained mismatch of crystal lattice and coalescence of crystallites. When surface cleaning is not satisfying, instantaneous stress is low but the electrodeposited layer being thickened increasingly stress become to high and peeling phenomenon occurs. Effect of current density and temperature on internal stress is variable. Internal stress increases rapidly at pH 5 and above because of codepositing colloidal materials caused hydrolysis. Concentrations of nickel ion and $H_3BO_3$ ion affect little on internal stress and solution which contains impurities tend to increase stress. Especially impurities of $H_2O_2$ and iron ion have a great effect on internal stress. Additives are divided in two kind. One is increasing tensile stress another is increasing compressive stress. Concentrations of additives have a great effect on internal stress.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2006.11a
• /
• pp.116-117
• /
• 2006

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.04a
• /
• pp.61-61
• /
• 2005

• Resources Recycling
• /
• v.21 no.5
• /
• pp.3-17
• /
• 2012

Selective leaching processes for copper, gold, nickel, and cobalt have been investigated because there is an advantage of ammoniacal hydrometallurgy that metal such as copper could be selectively extracted restricting the dissolution of iron or calcium. In the present article, the studies for selective ammoniacal leaching of copper from motor scraps and waste printed circuit boards (PCBs), for ammoniacal leaching of gold to decrease the amount of cyanide used or to substitute cyanide by thiosulfate, and for ammoniacal leaching to recover nickel and cobalt from nickel oxide ore and intermidiate obtained from manganese nodule treatment process were summarized and further studies were proposed for domestic technology development for ammoniacal hydrometallurgy processes.

• Korean Journal of Materials Research
• /
• v.18 no.6
• /
• pp.298-301
• /
• 2008

A preparation of $Ni_xMn_{1-x}Fe_2O_4$ nanoparticles produced via the reduction of Nickel nitrate hexahydrate, Manganese (II) nitrate hexahydrate and Iron nitrate nonahydrate with hydrazine in Igepal CO-520/cyclohexane reverse micelle solutions was investigated. Transmission Electron Microscope (TEM), X-ray Diffraction (XRD) and Vibration Sample Magnetometer (VSM) analyses showed that the resultant nanoparticles increased the molar ration of water to Igepal CO-520 as the concentrations of Nickel nitrate hexahyrate, Manganese (II) nitrate hexahydrate and Iron nitrate nonahydrate increased. The average size of the synthesized particles calcined at $600^{\circ}C$ for 2hrs was in the range of 20 nm to 30 nm, and the particle distribution was broadened. The phase of the synthesized particles was crystalline, and the magnetic behavior of the synthesized particles was superparamagnetism. The effect of the synthesis parameters of the molar ratio of water to surfactant and the calcination temperature was discussed.

• Journal of Magnetics
• /
• v.14 no.2
• /
• pp.66-70
• /
• 2009

The dynamic magneto-mechanical behaviors in a type of iron-nickel-based ferromagnetic alloy with constant elasticity were investigated as a function of both the DC bias magnetic field ($H_{dc}$) and the frequency. The rectangular plate-like samples were excited to vibrate at a half-wavelength, longitudinal resonance by an AC magnetic field superimposed with various $H_{dc}$. The experimental results found that the strain coefficient at resonance reached 819.34 nm/A and the effective mechanical quality factor ($Q_m$) was greater than 2000. The ratio of the maximum variation of the Young's modulus over $H_{dc}$ to the value of the Young's modulus at a zero bias field was only ${\sim}0.83%o$ because of the so-called constant elasticity. The resonant strain coefficients and $Q_m$ are strongly dependent on $H_{dc}$, which indicates a promising potential for use in DC and quasistatic magnetic field sensing.

• Corrosion Science and Technology
• /
• v.18 no.1
• /
• pp.8-15
• /
• 2019

A high-temperature gas-cooled reactor (HTGR) is recognized as the best candidate reactor for next generation nuclear reactors. Helium is used to be the coolant in the core of the HTGR with temperature expected to exceed $900^{\circ}C$ at the core outlet. Several iron- and nickel-based superalloys, including Alloy 800H, Hastelloy X, and Alloy 617, are potential structural materials for intermediate heat exchanger (IHX) in an HTGR. Oxidation behaviors of three selected alloys (Hastelloy X, Alloy 800H, and Alloy 617) were investigated at four different temperatures from $650^{\circ}C$ to $950^{\circ}C$ under helium environments with various concentrations of $O_2$ and $H_2O$. Preliminary results showed that chromium oxide as the primary protective layer was observed on surfaces of the three tested alloys. Based on results of mass gain and SEM analyses, Hastelloy X alloy exhibited the best corrosion resistance in all corrosion tests. Further details on the oxidation mechanism of these alloys are presented in this study.

• Journal of Adhesion and Interface
• /
• v.19 no.4
• /
• pp.167-172
• /
• 2018

In this study, a polyurethane hot melt adhesive was synthesized and metal particles sensitive to induction heating were added to produce an induction heating melt adhesive. The thermal behavior and adhesion characteristics of metal particles were investigated according to the kind, size and induction heating conditions. Among the various metal particles, induction heating efficiency was the best when nickel and iron were applied. Induction heating efficiency increased with decreasing metal particle size. In addition, the strength of the induction heating power of the adhesive was high and the adhesive strength was improved as the adhesive thickness was thinner.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.4
• /
• pp.398-405
• /
• 2021

To fabricate a full-scale pilot model of the cost-effective Na-(Ni,Fe)Cl₂ cell, a Na-beta-alumina solid electrolyte (BASE) was developed by applying a one-step synthesis cum sintering process as an alternative to the conventional solid-state reaction process. Also, Fe metal powder, which is cheaper than Ni, was mixed with Ni metal powder, and was used for cathode material to reduce the cost of raw material. As a result, we then developed a prototype Na-(Ni,Fe)Cl₂ cell. Consequently, the Ni content in the Na-(Ni,Fe)Cl₂ cell is decreased to approximately (20 to 50) wt.%. The #1 prototype cell (dimensions: 34 mm × 34 mm × 235 mm) showed a cell capacity of 15.9 Ah, and 160.3 mAh g^-1 (per the Ni-Fe composite), while the #2 prototype cell (dimensions: 50 mm × 50 mm × 335 mm) showed a cell capacity of 49.4 Ah, and 153.2 mAh g^-1 at the 2^nd cycle.