• 수산해양기술연구
• /
• 제50권2호
• /
• pp.162-168
• /
• 2014

The friction and wear characteristics of the rubber matrix composites filled with nano sized silica particles were investigated at ambient temperature by pin-on-disc friction test. The volume fraction of silica particles was 19%. The cumulative wear volume and wear rate of these materials on counterpart roughness were determined experimentally. The major failure mechanisms were lapping layers, deformation of matrix, ploughing, debonding of particles, fracture of particles and microcracking by scanning electric microscopy photograph of the tested surface. The cumulative wear volume showed a tendency to increase with increase of sliding distance. The wear rate of these composites tested indicated low value as increasing the sliding distance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.202-202
• /
• 2009

대전제어제를 이용하여 전하량을 가지는 토너 입자를 제조하고, 입자의 유동성을 부여하기 위하여 입자의 표면처리를 하였다. 제조된 토너 입자의 크기는 약 $8{\mu}m$정도이며, 표면 처리를 위해 크기가 약 14nm 정도인 nano-silica를 사용하였다. 대전제어제가 첨가된 토너 입자의 평균 전하질량비는 30.9uC/g이고, 표면처리를 한 입자의 전하질랑비는 외첨 시간이 증가함에 따라 점차적으로 감소하는 것을 관찰 할 수 있었다. 또한 표면처리가 된 입자의 유동성은 표면처리를 하지 않은 입자 보다 우수하다는 것을 관찰 할 수 있었다.

• 전기학회논문지
• /
• 제65권10호
• /
• pp.1712-1720
• /
• 2016

AC and DC insulation breakdown voltage was studied for magnet wire coated with double layers of high flexural PAI layer and high anti-corona PAI/nanosilica (15 wt%) layer. The specimens were prepared at various drying temperatures (T/D): $22^{\circ}C$, $240^{\circ}C$, and $260^{\circ}C$, respectively. The increase effects of nanosilica on AC and DC insulation breakdown voltage were not so significant compared to that of magnet wire coil coated with original PAI. And the AC and DC insulation breakdown voltage was improved by decreasing diameter of winding coil. As T/D temperature increased, AC and DC insulation breakdown voltage decreased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.142-142
• /
• 2010

This research proposed an advanced Electronic bead (EB) using MMA (Methy methacrylate) and CCA (Charge Control Agent). In the first, this paper presents about measurement method and characterization analysis of EB and nano-silica with pulse waveform in aging. Furthermore; this work presents the positive and negative EB fabrication procedure. As the experimental results, the proposed EB with square waveform is very attractive to Electronic paper driving characterization.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.377-378
• /
• 2010

본 연구는 해양콘크리트용 소재로서 나노실리카의 종류 및 혼입량에 따른 시멘트 복합체의 공학적 특성을 분석하였으며, 시험 결과 시멘트 복합체의 강도 및 공극 특성 개선에 효과적인 나노실리카는 Sodium Silicate계인 것으로 나타났으며, 적정 혼입률은 5% 이하인 것으로 나타났다.

• KSBB Journal
• /
• 제29권1호
• /
• pp.9-21
• /
• 2014

One of the most abundant microalgaes, diatom is characterized by its unique cell wall structures composed of nano-patterned silica. Due to its highly ordered porosity, these silica frustules, which are found as sediments called diatomite, were used as a cheap adsorption material for water purification. Recently, new emerging nanotechnology compels many researchers to have interest in such diatom's unique properties (eg, nano-scale mesoporosity, photo luminescence, light transparency, etc.) as biogenic inorganic materials as well as the biomass resource (conventional usage of microalgae). In this review, we will focus on the current knowledge about the diatoms research and the possibility of its applications.

• 한국세라믹학회지
• /
• 제37권3호
• /
• pp.280-287
• /
• 2000

Adsorption behavior and amount of phenolic resin followed silica (SiO2) formation onto silicon nitride(Si3N4) surface were investigated using electrokinetic sonic amplitude (ESA) technique and with UV spectrometer, to fabricate Si3N4/SiC nano-composite based on reaction between SiO2 formed and phenolic resin absorbed onto Si3N4 particle. The amount of SiO2 formed and carbon from phenolic resin absorbed onto Si3N4 surface were calculated quantitatively to adjust the reaction between SiO2 and phenolic resin, resulting in no residual SiO2 and carbon. As a result, pre-heated tempeature for optimized reaction was below 25$0^{\circ}C$, in which there was no residual SiO2 and carbon.

• Bulletin of the Korean Chemical Society
• /
• 제30권7호
• /
• pp.1641-1643
• /
• 2009

• Bulletin of the Korean Chemical Society
• /
• 제35권9호
• /
• pp.2621-2624
• /
• 2014

The rapid and spontaneous adsorption of proteins on nanoparticle (NP) surfaces in biological fluids such as blood is an important phenomenon as it possibly determines "what the cells see" and, thus, the fates of NPs in living organisms. In order to quantitatively understand protein coronas at the molecular level, we investigated human serum albumin (HSA) coronas that were produced on silica NPs of 20 nm and 50 nm diameters using conventional gel electrophoresis. Analysis of the concentration dependence of protein adsorption showed that HSA coronas preferentially formed a monolayer on silica NPs and revealed the presence of hard protein coronas. HSA adsorption was clearly dependent on NP size, and this might be due to the different surface curvatures of NPs of different sizes.

• 센서학회지
• /
• 제16권1호
• /
• pp.77-83
• /
• 2007

Nanoporous silica aerogels with various surface modifiers were prepared by ambient drying process. Tetraethylorthosilicate (TEOS) were used a raw material. Ambient drying process for various surface modifier was studied in the point of view of a crack-free monolith and thin films and low cost. Various kinds of surface modifiers like as hexamethyldisilazane (HMDSZ), trimethlychlorosilane (TMCS), methlytriethoxylsilane (MTES), and methlytrimethoxysilane (MTMS) were studied in order to enhance hydrophobicity for the silica aerogel. Surface modified aerogels were evaluated by FT-IR, TG, BET, SEM and wetting angle measurement. Homogeneous and crack-free aerogels were obtained by modifying the HMDSZ and the TMCS. However silica xerogel was obtained when modified with MTMS, MTES.