• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.2
• /
• pp.202-211
• /
• 2014

The bulk current injection (BCI) and direct power injection (DPI) method have been established as the standards for the electromagnetic susceptibility (EMS) test. Because the BCI test uses a probe to inject magnetically coupled electromagnetic (EM) noise, there is a significant difference between the power supplied by the radio frequency (RF) generator and that transferred to the integrated circuit (IC). Thus, the immunity estimated by the forward power cannot show the susceptibility of the IC itself. This paper derives the real injected power at the failure point of the IC using the power transfer efficiency of the BCI method. We propose and mathematically derive the power transfer efficiency based on equivalent circuit models representing the BCI test setup. The BCI test is performed on I/O buffers with and without decoupling capacitors, and their immunities are evaluated based on the traditional forward power and the real injected power proposed in this work. The real injected power shows the actual noise power level that the IC can tolerate. Using the real injected power as an indicator for the EMS test, we show that the on-chip decoupling capacitor enhances the EM noise immunity.

• The KIPS Transactions:PartC
• /
• v.11C no.6 s.95
• /
• pp.765-772
• /
• 2004

Multicast communication is simultaneous transmission of data to multiple receivers and saves considerably sender resources and network bandwidth. It has high risk to attack using group address and inherent complexity of routing packets to a large group of receivers. It is therefore critical to provide source authentication, allowing a receiver to ensure that received data is authentic. In this paper, we propose the multiple chain authentication scheme for secure and efficient multicast stream. To evaluate the performance of our scheme, we compare our technique with two other previously proposed schemes using simulation results. Our scheme provides non-repudiation of origin, low overhead by amortizing the signature operation over multiple packets, and high packet loss resistance.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.11
• /
• pp.1579-1584
• /
• 2002

Since surfactant or emulsifiers remained on the nanoparticle surface significantly affect the physicochemical properties, the biodegradation rate, the biodistribution, and the biocompatibility of nanoparticles, surfactant-free nanoparticles should be good candidate. surfactant-free PLGA nanoparticles were successfully prepared by both the dialysis method and the solvent diffusion method. The PLGA nanoparticles prepared using the solvent diffusion method has a smaller particle size than the dialysis method. The solvent diffusion method was better for a higher loading efficiency than the dialysis method but the nanoparticle yield was lower. Testosterone (TST) release from the PLGA nanoparticles was dependent on the particle size rather than the drug contents. Testosterone release from the PLGA nanoparticles prepared by the solvent diffusion method using acetone was faster than those prepared by the dialysis method. TST release from the PLGA nanoparticles prepared by the solvent diffusion method using acetone and the dialysis method using dimethylformamide (DMF) was completed for 4 days while the PLGA nanoparticles prepared by the dialysis method using acetone showed approximately 80% TST release after 4 days. Since the PLGA nanoparticle degradation ratio was below 20% within 5 days at all samples while TST release completed within 4 days, TST release was dependent on the diffusion mechanism rather than degradation.

• Journal of electromagnetic engineering and science
• /
• v.7 no.4
• /
• pp.161-168
• /
• 2007

A fast correlative vector direction finding(CVDF) system using active dipole antenna array for mobile direction finding(DF) applications is presented. To develop the CVDF system, the main elements such as active dipole antenna, multi-channel direction finder, and search receiver are designed and analyzed. The active antenna is designed as composite structure to improve the filed strength sensitivity over the wide frequency range, and the multi-channel direction finder and search receiver are designed using DDS-based PLL with settling time of below 35 us to achieve short signal processing time. This system provides the capabilities of the high DF sensitivity over the wide frequency range and allows for high probability of intercept and accurate angle of arrival(AOA) estimation for agile signals. The design and performance analysis according to the external noise and modulation schemes of the CVDF system with five-element circular array are presented in detail.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.651-658
• /
• 2017

This paper proposes an analysis method of performance degradation of antenna due to radio frequency interference between an antenna and adjacent noise sources using active scattering parameters. The radio frequency interference can be analyzed by the measured or simulated scattering parameters and by excited noise sources in the circuit as well. In this paper, a planar inverted-F antenna and a noise source are designed and fabricated to analyze radio frequency interference between the planar inverted-F antenna and noise source. The proposed analysis method uses active scattering parameters, of which verification is experimentally verified, and in simulation as well.

• Korean Journal of Microbiology
• /
• v.38 no.4
• /
• pp.275-275
• /
• 2002

Pseudomonas sp. S-47 is capable of catabolizing 4-chlorobenzoate (4CBA) as carbon and energy sources under aerobic conditions via the mesa-cleavage pathway. 4CBA-dioxygenase and 4CBA-dihydrodiol dehydrogenase (4CBA-DD) catalyzed the degradation af 4CBA to produce 4-chlorocatechol in the pathway. In this study, the xylL gene encoding 4CBA-DD was cloned from the chromosomal DNA of Pseudomonas sp. S-47 and its nucleotide sequence was analyzed. The xylL gene was found to be composed of 777 nucleotide pairs and to encode a polypeptide of 28 kDa with 258 amino acid residues. The deduced amino acid sequence of the dehydrogenase (XylL) from strain S-47 exhibited 98% and 60% homologies with these of the corresponding enzymes, Pseudomonas putida mt-2 (XyIL) and Acinetobacter calcoaceticus (BenD), respectively. However, the amino arid sequences show 30% or less homology with those of Pseudomonas putida (BnzE), Pseudomonas putida Fl (TodD), Pseudomonas pseudoalcaligenes KF707 (BphB), and Pseudomonas sp. C18 (NahB). Therefore, the 4CBA-dihydrodiol dehdrogenase of strain S-47 belongs to the group I dehydrogenase involved in the degradation of mono-aryls with a carboxyl group.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.4 no.1
• /
• pp.33-39
• /
• 2013

Structural insulated panels, structurally performed panels consisting of a plastic insulation bonded between two structural panel facings, are one of emerging products with a viewpoint of its energy and construction efficiencies. These components are applicable to fabricated wood structures. In Korea, there are few technical documents regulated structural performance and engineering criteria in domestic market. This study was conducted to identify fundamental performance of both monotonic load and quasi static cyclic load for SIPs in shear wall application. Static test results showed that maximum load was 44.3kN, allowable shear load was 6.1kN/m, shear stiffness was 1.23 M N/m, and ductility ratio was 3.6. Cyclic test was conducted by two kinds of specimens : single panel and double panels. Cyclic test results, which were equivalent to static test results, showed that maximum load was 45.42kN, allowable shear load was 6.3kN/m. Furthermore the accumulated energy dissipation capability for double panels was as 2.3 times as that for single panel. From performance of structural tests, it was recommended that the allowable shear load for panels was at least 6.1kN/m.

• Korean Journal of Veterinary Research
• /
• v.39 no.4
• /
• pp.710-714
• /
• 1999

In veterinary medicine amitraz has been used as an insecticide to eliminate mites, lice, and ticks in dogs, cats, goats, swine and cattle. We performed the experiment on bradycardiac effect of arnitraz in rabbits. Under anesthetized with urethane (1g/kg, 25% w/v, SC), the femoral artery was cannulated by a polyvinyl tube which was connected with pressure transducer for continuous measurement of heart rate. Amitraz (0.5-2.5mg/kg, IV) reduced the heart rate in a dose-dependent manner. Pretreatment of yohimbine (2.0mg/kg) or atropine (2.0mg/kg and 4.0mg/kg) affected the response of amitraz but pretreatment of prazosin (0.5mg/kg) or propranolol (1.0mg/kg) did not. Moreover, the effect of amitraz was blocked by vagotomy. The result of our experiment suggest that amitraz may reduce the heart rate by increasing acetylcholine through activating vagal nerves and ${\alpha}_2$-adrenoceptors could be involved in activating vagal nerves.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.4
• /
• pp.410-416
• /
• 2009

In recent years, the rollover accident of large class of vehicles has become important safety issue. Even though the rollover form a small percentage of all traffic accidents, they have a fatal effect upon the driver and passenger. Among the traffic accidents occurred in driving, the rollover is the major cause of traffic fatalities. Therefore, it is required to develop the analytical and experimental techniques for predicting rollover propensity of vehicles and also to improve the vehicle suspension design in the viewpoint of rollover resistance. In this study, the parameter sensitivities for the roll angle of SUV suspension are analyzed, and then the determined design parameters are optimized by using the regression model function of the response surface methods. The analysis results show that the roll angle of the optimized vehicle is decreased as compared with the initial vehicle and also the rollover possibility is decreased when the roll rate of the front suspension is larger than the roll rate of the rear suspension.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.48-53
• /
• 2006

A methodology is described for predicting the fatigue life of the resistance spot weldment including strain rate effect. Because it is difficult to perform a physical failure test with high strain rate, an analytical method is necessary to get the mechanical properties of various strain rate, To this end, quasi-static tensile-shear tests at several strain rate were performed on spot weldments of SPC. These test provided the empirical data with the strain rate. With these results, we formulated the function of fatigue life prediction using the lethargy coefficient which is the global material property from tensile test. And, we predicted the fatigue life of spot weldment at dynamic strain rate. To confirm this method for fatigue life prediction, analytical results were compared with the experimental fatigue data.