• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.5
• /
• pp.555-560
• /
• 2014

In order to improve spectrum sensitivity of photodiode for detection of the laser wavelength at 850 nm ~ 1000 nm of near-infrared band, this study has produced silicon-based photodiode whose area is $5000{\mu}m{\times}2000{\mu}m$, and the thickness is $280{\mu}m$. It was packed by the TO-5 type. The electrical properties of the dark currents have valued of approximately 0.1 nA for 5 V reverse bias, while the capacitance showed 32.5 pF at frequency range of 1 kHz and about 32.4 pF at the range of 200 kHz for 0 V. In addition, the rising time of output signal was as fast response as 20.92 ns for 10V. For the optical properties, the best spectrum sensitivity was 0.57 A/W for 890 nm, while it was relatively excellent value of 0.37 A/W for 1,000 nm. Over all, there were good spectrum sensitivity for this diode over the range of 870 ~ 920 nm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1218-1226
• /
• 2008

With the development of semiconductor integrated technology and with the increasing use of multimedia functions in computer, more functions have been implemented as hardware. Nowadays, most microprocessors beyond 32 bits generally implement an integer multiplier as hardware. However, as for a divider, only specific microprocessor implements traditional SRT algorithm as hardware due to complexity of implementation and slow speed. This paper suggested an algorithm that uses a multiplier, 'w bit $\times$ w bit = 2w bit', to process $\frac{N}{D}$ integer division. That is, the reciprocal number D is first calculated, and then multiply dividend N to process integer division. In this paper, when the divisor D is '$D=0.d{\times}2^L$, 0.5 < 0.d < 1.0', approximate value of ' $\frac{1}{D}$', '$1.g{\times}2^{-L}$', which satisfies ' $0.d{\times}1.g=1+e$, $e<2^{-w}$', is defined as over reciprocal number and then an algorithm for over reciprocal number is suggested. This algorithm multiplies over reciprocal number '$01.g{\times}2^{-L}$' by dividend N to process $\frac{N}{D}$ integer division. The algorithm suggested in this paper doesn't require additional revision, because it can calculate correct reciprocal number. In addition, this algorithm uses only multiplier, so additional hardware for division is not required to implement microprocessor. Also, it shows faster speed than the conventional SRT algorithm and performs operation by word unit, accordingly it is more suitable to make compiler than the existing division algorithm. In conclusion, results from this study could be used widely for implementation SOC(System on Chip) and etc. which has been restricted to microprocessor and size of the hardware.

• Publications of The Korean Astronomical Society
• /
• v.10 no.1
• /
• pp.15-30
• /
• 1995

It has been recognized that the morphologies of the SNRs from the radio observation are "barrel shaped". To interpret the mechanism of the radiation and the physical state of the environments, we have analytically calculated the dynamical structure of the interacting region in the case where the ejectum has a steep power-law density profile($\rho{\sim}r^{-n}$) and the ambient medium has a shallow power-law density profile($\rho{\sim}r^{-s}$), assuming that the cosmic rays are isotropically accelerated in the shock wave and the magnetic fields are very weak. The calculated synchrotron radio maps show that the emission from the equator is intense and the emissions from the central and polar regions are less intense. Also the thicknesses of the shell are strongly dependent on s and weakly on n. The azimuthal intensity ratio $\alpha$ increases as the efficiency of the cosmic ray acceleration increases and s decreases. We compared the results with the morphology of the SNR A. D. 1006(type I SNR). It does agree with the case of s = 0, w = 0.3 - 0.5. This value for w is consistent with the results by Eichler(1979). It provides us the evidence of the cosmic ray acceleration in the shock wave.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.26-31
• /
• 2015

This paper describes the characteristics of voltage drop and thermal for poor connection on electrical connector of circuit breaker in control box of small size pulverizer. In order monitor, we did the changes of RMS in voltage and temperature value with video and made normal state over $2.5N{\cdot}m$ and poor connections state below $0.2N{\cdot}m$ by screw gage. In case of voltage signal, the voltage drop was increased when the current was increased due to poor connections. In case of temperature signal, the temperature difference indicates ten times at 5A and fourteen times at 15A in the normal state. According to increase thermal energy, the insulation of electrical wiring and connector of circuit breaker can be carbonized. The results of this study will be useful to the development of preventive devices and system for electric fire by poor connection at small size pulverizer.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.09a
• /
• pp.52-55
• /
• 2003

The objective of this study is to investigate the vertical variation of heavy metals in tailings from the Sangdong W mine. Tailings samples were taken at 6 drilling sites with 50cm intervals up to 21meters in depth and dried at room temperature. The pH value, loss-on-ignition and water contents were measured. In addition, chemical compositions of the samples were determined by AAS after 0.1N HC1 leaching and ICP-AES after aqua regia leaching. The pH values were in the range of 7.2 to 8.5 due to chemical reactions of carbonate minerals. The ranges of heavy metals (mg/kg) extracted by 0.1N HC1 were from 0.17 to 0.93 for Cd, 0.04 to 4.39 for Cu, 0.03 to 10.9 for Pb and 0.06 to 14.1 for Zn and those extracted by aqua regia were 3.10~10.5, 23.61 ~251, 63.7~337 and 42.6~134 for Cd, Cu, Pb and Zn, respectively. Generally, the metal concentrations in tailings do not change with depth, with they have a tendency to decrease with depth in some case.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.506-509
• /
• 2003

In this paper, the $\Phi$-q-n pattern and average discharge power of silicone rubber have investigated effect of inter impurities. It's changed impurities by silicone oil, water and copper. Applied voltage is AC 3, 4, 4.5, 5, 5.5[kV]. And data acquisition time is 10 second(600 cycles). These results suggest that partial discharge(PD) is shower negative polar than positive polar at 3[kV]. Positive polar's PD value increased with increase of applied voltage. The Conductivities expressed same $\Phi$-q-n pattern in positive polar and negative polar at phase region.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.106-109
• /
• 2005

The $(Sr_{1-x}Ca_x)TiO_3$(SCT) thin films are deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method with substitutional contents of Ca. The optimum conditions of RF power and Ar/$O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin film was about 18.75[$\AA$/min]. The dielectric constant was increased with increasing the substitutional contents of Ca, while it was decreased if the substitutional contents of Ca exceeded over 15[mol%]. The capacitance characteristics had a stable value within ${\pm}4$[%] in temperature ranges of -80~+90[$^{\circ}C$].

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1496-1498
• /
• 2003

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films were deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method according to the deposition condition. The optimum conditions of RF power and Ar/$O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about 18.75[${\AA}/min$] at the optimum condition. The capacitance characteristics had a stable value within ${\pm}4[%]$. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films were observed above 200[kHz].

• Journal of Environmental Science International
• /
• v.4 no.5
• /
• pp.413-426
• /
• 1995

The aim of the present study is to investigate the interannual variabilities of the East Asia monsoon rainfall associated with the global sea surface temperature anomaly(SSTA). For this study, the summer rainfall(from June to August) over the twenty-eight period of 1961-1988 were analyzed with being divided by nine-subregions over East Asia including Korea, China and Japan. From the analysis of the principal modes explaining the interannual variation, the interannual variabilities of summer rainfalls in South Japan and Korea are larger than those of the other subregions of the East Asia. There is a strong negative correlation between the summer rainfalls of south China and Korea. In this study, the relationship between the summer monsoon of each subregion and SSTs of the tropical NINO regions, of western Pacific warm pool, and of the subtropical ocean were investigated. The longitudinal sections of the lagged cross correlations of the summer rainfal1 anomaly in (a) Korea and (b) south China, and the monthly SSTA in the equatorial(averaged from 65 to 6N) Pacific were analyzed. The negative maximum correlation pattems of Korea's stammer rainfal1 and SSTs over the eastern Pacific is transfered to positive maximum conrlation over central Pacific region with a biennial periodicity. In South China, the significant positive correlations are found at -12 month lag over the eastern Pacific and maximum negative correlation at 16 month lag over the central Pacific with the quasi-biennial oscillation. But the correlation coefficient reverses completely to that in Korea. In order to investigate the most prevailing interannual variability of rainfall related to the favored SSTA region, the lagged cross correlations between East Asia rainfall and SSTs over the moO regions(NINO 1+2(0-105, 90W-80W), NINO 3(5N-5S, 150W-90W), NINO 4(5N-5S, 160E-l50W) and the western Pacific worm pool (5N-5S, 120E-l60E) were analyzed. Among the lagged cross-correlation cycles in NINO regions, the maximum correlations for the negative lagged months prevail in NINO 1+2 and NINO 3, and the cross correlations for the positive lagged months NINO 4. It is noteworthy that correlation between the western Pacific warm pool SSTA and the monsoon rainfall in Korea and South China have the maximum value at negative 4 month lag. The evolution of the correlation between the East Asia monsoon rainfall and SSTA is linked to the equatorial convective cluster and related to northward propagating situation, and raising the possibility that the East Asia monsoon precipitation may be more fundamentally related to the interaction of intraseasonal oscillations and the sub-regional characteristics including the surface boundary conditions and the behavior of climatological air mass.

• Journal of Bio-Environment Control
• /
• v.22 no.3
• /
• pp.284-290
• /
• 2013

This study analyzed the geometric, compressive, cutting and friction properties of oriental melons in order to design a gripper capable of soft handling and a cutter for cutting oriental melon vine among the end effector of oriental melon as a preliminary step for developing the end effector of the robot capable of harvesting oriental melons in protected cultivation. As a result, the average length, diameter at the midpoint, weight, volume and roundness of the oriental melons were 108 mm, 70 mm, 188 g, 333 mL and 3.8 mm. Nonlinear regression analysis was performed on the equation $W=L^a{\times}D_2^b$ with variation of the length (L) and diameter (D2) of the weight (W) of the oriental melons. As a result, it was shown that there was a correlation between a of 2.0279 and b of -0.9998 as a constant value. The average diameter of the oriental melon vine was 3.8 mm, and most vines were distributed within a radius of 5 mm from the center. The average yield value, compressive strength and hardness of the oriental melons were $36.5N/cm^2$, $185.7N/cm^2$ and $636.7N/cm^2$, respectively. The average cutting force and shear strength of the oriental melon vines were $2.87{\times}10^{-2}\;N$ and $5.60N/cm^2$, respectively. The maximum friction coefficient of the oriental melons was rubber of 0.609, followed by aluminium of 0.393, stainless steel of 0.177 and teflon of 0.079. It was considered possible to apply it to the size of the gripper and cutter, turning radius, dynamics of drive motor and selection of materials and their quality in light of the position error and safety factor according to the movement when designing end effector based on the analyzed data.