• Journal of Environmental Science International
• /
• v.24 no.1
• /
• pp.133-150
• /
• 2015

Wind profiler provides vertical profiles of three-dimensional wind vectors with high spatiotemporal resolution. The wind vectors is useful to analyze severe weather phenomena and to validate the various products from numerical weather prediction model. However, the wind measurements are not immune to ground clutter, bird, insect, and aircraft. Therefore, quality of wind vectors from wind profiler must be quantitatively evaluated prior to its application. In this study, wind vectors from UHF wind profiler at Ganwon Regional Meteorological Administration was quantitatively evaluated using 27 radiosonde measurements that were launched every two or three hours according to rainfall intensity during Intensive Observation Period (IOP) from June to July 2013. In comparison between two measurements, wind vectors from wind profiler was relatively underestimated. In addition, the accuracy and quality of wind vectors from wind profiler decrease with increasing beam height. The accuracy and quality of the wind vectors for rainy periods during IOP were higher than for the clear-air measurements. The moderate rainfall intensity lead to multi-peaks in Doppler spectrum. It results in overestimation of vertical air motion, whereas wind vectors from wind profilers shows good agreement with those from radiosonde measurements for light rainfall intensity.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2070-2076
• /
• 2015

Nano composite materials were multi-constituent combinations of nano dimensional phases with distinct differences in structure, chemistry and properties. Nano particles were less likely to create large stress concentrations and thereby can avoid the compromise of the material ductility while improve other mechanical properties. Corona discharge was an electrical discharge. The ionization of a fluid surrounding a conductor was electrically energized. This discharge would occur when the strength of the electric field around the conductor was high enough to form a conductive region, but not high enough to cause electrical breakdown or arcing to nearby objects. This paper shows all the studies done on the preparation of nano fillers. Special attention has given to the ACSR transmission line conductor, TiO₂ nano fillers and also to the evaluation of corona resistance on dielectric materials discussed in detail. The measurement of the dielectric properties of the nano fillers and the parameters influencing them were also discussed in the paper. Corona discharge test reveals that in 0%N ACSR sample corona loss was directly proportional to the applied line voltage. No significant change in corona loss between 0%N and 1%N. When TiO₂ nano filler concentration was increased up to 10%N fine decrement in corona loss was found when compared to base ACSR conductor, corona loss was decreased by 40.67% in 10%N ACSR sample. It was also found from the surface conditions test that inorganic TiO₂ nano filler increases the key parameters like tensile strength and erosion depth.

• Fashion & Textile Research Journal
• /
• v.20 no.4
• /
• pp.439-448
• /
• 2018

This thesis intends to suggest a new wedding dress pattern through researches on history and changes of wedding dress, researches on silhouette and details and analyses of existing basic patterns. In this study, to develop torso patterns of top dresses selected as preferred designs through literature reviews and company surveys, dress form sizes suitable for standard sizes were selected and study basic patterns were made using draping techniques. The study finds characteristics of body type dimension that is changed when wearing brassiere (hereinafter, 'bra') for wedding dress through customer surveys for development of basic patterns of wedding dress. That is, wearing wedding bra was used for the purpose of increasing the bust size and we will evaluate later whether this increase helps completeness of aesthetic impression through wearing evaluation. As the result, it was found out that top torso pattern wearing wedding bra made wearers feel more comfortable and in the aspect of aesthetic impression, it provided impacts on women's beautiful silhouettes. The effects of whether a bra is used or not on changes in patterns were reviewed through the degree of polymerization of finished patterns. When a bra for dresses was worn, the waist front length increased by1.7cm, the bust circumference increased by 2.1cm, and the amount of dart increased by 1.5cm in the patterns. A new torso pattern for top dresses, which will solve problems evaluated in each of the above from the aspect of composition of pattern by a method through analysis of existing basic patterns and multi-dimensional cut patterns wearing wedding bra, will be suggested.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.4
• /
• pp.47-56
• /
• 2017

Aseismic designs of pile-supported wharves are commonly performed utilizing simplified dynamic analyses, such as multi-mode spectral analyses. Simplified analyses can be useful for evaluating the limit state of structures. However, several pile-supported wharves, that have been damaged during past earthquakes, have shown that soil deformation and soil-pile dynamic interaction significantly affect the entire behavior of structures. Such behavior can be captured by performing nonlinear effective stress analyses, which can properly consider the dynamic interactions among the soil-pile-structure. The present study attempts to investigate the earthquake performance of a pile-supported wharf utilizing a three-dimensional numerical method. The damaged pile-supported wharf at the Kobe Port during the Hyogo-ken Nambu earthquake (1995) is selected to verify the applicability of the numerical modeling. Analysis results showed a suitable agreement with the observations on the damaged wharf, and the significant effect of excess pore pressure development and pile-soil dynamic interaction on the seismic performance of the wharf.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.96-101
• /
• 2011

Korea Aerospace Research Institute is performing 3 stage transonic axial compressor development program. This paper introduces design step of the compressor, the performance test results and its analysis. In the fore part of the paper, aerodynamic process of the 3 stage axial compressor is presented. To satisfy both of the mass flow and pressure rise, the compressor should rotate at a high rotational speed. Therefore the transonic flow field forms in the rotor stages and it is designed with a relatively high pressure rise per stage to satisfy its design target. The compressor stage consists of 3 stages, and the bulk pressure ratio is 2.5. The first stage is burdened with the highest pressure ratio and less pressure rises occur in the following stages. Also it is designed that tip Mach number of the first rotor row does not exceed 1.3, while the maximum relative Mach number in the rotor stage is between 1.3~1.4 to increase the compressor flow coefficient. The final design has been confirmed by iterating three dimensional CFD calculations to verify design target and some design intentions. In the latter part of the paper, its performance test processes and results are presented. The performance test result shows that the overall compressor performance targets; pressure ratio and efficiency are well achieved. The stator static pressure distributions show that the blade loading is gradually increasing from the downstream of the compressor.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.334-343
• /
• 1996

Quality evaluation for food and agricultural products have always been one of the most elusive problems associated with the handling , processing and marketing in a food plant production. In order to detect physical foreign materials in food and agricultural products, non-destructive techniques have been developed for many years. Application of X-ray system to detect physical foreign materials in food and agricultural products could be considered to be a high potential method. Especially , it is impossible to detect internal physical foreign materials by visual inspections. In this study, it was tried to be applied for two different X-ray devices. Soft X-ray system with CdTe sensor and X-ray CT scanner were evaluated for advantage of the detection of non-meltallic foreign materials in food and agricultural products . Though the soft X-ray is not a high energy radiation, it is possible to detect small different density in a material. The CdTe sensor has a high resolution for t e soft X-ray energy region. The density characteristics of foods and foreign material were expressed region. The density characteristics of foods and foreign materials were expressed as a soft X-ray energy spectrum. The energy spectrum was analyzed by a personal computer with a multi-channel analyzer. X-ray CT scanner can provide visual image and analyze by three dimensional information inside food and agricultural products. The X-ray CT scanner using as a medical equipment was used to detect a foreign material. The density characteristics of food and foreign materials in food were tried to be detected by the threshold value on the basis of the CT numbers. The soft X-ray absorption characteristics for acrylin plates and distilled water were obtained and could be found the possibility of detecting a small physical foreign materials such as a plastic wrapping film , a stone and grasshopper in food and agricultural products.

• Science of Emotion and Sensibility
• /
• v.8 no.4
• /
• pp.355-363
• /
• 2005

The adjectives for represnting emotions is important to evaluate and select the colors or color patterns. In this paper, we perform the MDS analysis, factor analysis, and cluster analysis to the Soen's experimental data obtained from the evaluation of random color patterns with 13 adjective pairs. As a result, those adjectives can be reduced 3 different factors representing emotions of weight, activity and temperature, which is approximately corresponds the results of previous researches on single colors. Also, we show that the adjectives for preference can be approximate4 by other primary adjectives for color patterns using regression analysis. This implies that one can construct a uniform emotion space for evaluating and selecting color patterns regardless of objects such as wall papers, carpets, and so on.

• Journal of Veterinary Clinics
• /
• v.31 no.5
• /
• pp.376-381
• /
• 2014

In this study, we analyzed the computed tomography (CT) measurements of lung volume and density in dogs with relation to body weight, age, sex, and breed. The multi-detector CT examination of the thorax was performed on dogs without respiratory or cardiovascular diseases. Three-dimensional reconstruction of CT images facilitated measurement of lung volume and density. There was a statistical significant correlation between body weight and lung volume (p < 0.0001). Lung density significantly decreased with an increase in body weight (p = 0.0078). However, no correlation was seen between these lung parameters and either sex or age of the dogs. In conclusion, this study shows that body weight is an important factor to consider when interpreting total lung volume and density values measured by quantitative CT. We highlight the need for further study using quantitative CT in identifying the potential effects of sex, age, and disease status on these parameters.

• Restorative Dentistry and Endodontics
• /
• v.37 no.1
• /
• pp.34-40
• /
• 2012

Objectives: The aim was to confirm the stem cell-like properties of the dental pulp stromal cells and to evaluate the morphologic changes during in vitro chondrogenesis. Materials and Methods: Stromal cells were outgrown from the dental pulp tissue of the premolars. Surface markers were investigated and cell proliferation rate was compared to other mesenchymal stem cells. Multipotency of the pulp cells was confirmed by inducing osteogenesis, adipogenesis and chondrogenesis. The morphologic changes in the chondrogenic pellet during the 21 day of induction were evaluated under light microscope and transmission electron microscope. TUNEL assay was used to evaluate apoptosis within the chondrogenic pellets. Results: Pulp cells were CD90, 105 positive and CD31, 34 negative. They showed similar proliferation rate to other stem cells. Pulp cells differentiated to osteogenic, adipogenic and chondrogenic tissues. During chondrogenesis, 3-dimensional pellet was created with multi-layers, hypertrophic chondrocyte-like cells and cartilage-like extracellular matrix. However, cell morphology became irregular and apoptotic cells were increased after 7 day of chondrogenic induction. Conclusions: Pulp cells indicated mesenchymal stem cell-like characteristics. During the in vitro chondrogenesis, cellular activity was superior during the earlier phase (within 7 day) of differentiation.

• Journal of the Ergonomics Society of Korea
• /
• v.26 no.3
• /
• pp.81-89
• /
• 2007

The purpose of this study is to develop data base and interface for sofa consumers and sofa designers. The human sensibility ergonomics method was used to find the consumer needs and Quality Function Deployment (QFD) method was used to extract the designing characteristics required for sofa production. About 200 words and 100 images were gathered from sofa and furniture related catalogs and internet sites to find the best emotional words and images that can express the various sofa aspect. Among the collected words and images, 34 emotional words were selected for sensibility experiment according to the opinions of experts, relations of closeness and frequency of use, and 50 images were selected for the experiment by the diversity. Selected words and images were used for the semantic differential method with 94 subjects, and sensibility characteristics of sofas were defined through various statistical analysis methods including basic statistical analysis, factor analysis and multi-dimensional scale. In reflecting design characteristics of sofas, design factors of sofas were divided into backrest, seat, armrest, neck support and leg, and relative importance of each factor for design was determined with analytic hierarchy process (AHP) by utilizing the experts' opinions. Based on the results above, relationship analysis between emotional evaluation results and design factors was performed. Also, as various sofa images are presented diagrammatically through multidimensional scaling method, it can be used as an important tool for the development of sofa design. This study will contribute improving the product quality of sofas as it enables applying consumer needs into the sofa design.