• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.8
• /
• pp.1407-1417
• /
• 2016

In this paper, we propose a multi-level content transmission mechanism for intelligent quality of service (QoS) in social networking services (SNSs). Because existing SNSs and related work send image content to a client with a single fixed mechanism, they cannot consistently support content accessibility according to different conditions of QoS factors such as network congestion and throughput. In the proposed image transmission mechanism, our communication middleware (CM) provides an SNS developer with three transmission modes so that an SNS server or client can dynamically change the quality of images if required. In each transmission mode, an SNS server can send images to a requesting client with original high quality, thumbnail quality, or send only text information. With varying qualities of downloaded images, an SNS developed on top of CM can provide users with consistent QoS for access to SNS content.

• Steel and Composite Structures
• /
• v.46 no.6
• /
• pp.823-837
• /
• 2023

This paper presents the seismic performance of seven beam-column joints with an eccentricity between beam depths under cyclic loadings. The failure modes of the panel zone were divided into two types. One was the shear force failure that appeared in the entire panel zone (SFEPZ), the other was the shear force failure that appeared in the partial panel zone (SFPPZ). Seven finite element models were established using multi-scale methods. Compared with the experimental specimens, the hysteretic loops exhibited a similar trend. The multi-scale models could accurately simulate the experimental results. Furthermore, the calculation formulas of yield and plastic shear capacity of unequal-depth joints with outer annular stiffener were proposed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.75-85
• /
• 2014

Existing car-sharing systems have difficulty meeting the demands of one-way trips and connecting to other sharing systems. Therefore, in this study, a multi-mobility sharing service management system that was able to meet the demands of the one-way and round-way trips and shared diverse transportation modes such as cars (electric car/gasoline car), electric motorcycles and bicycles was developed, and a field study was conducted in Kashiwa-no-ha, Kashiwa City and Nagareyama City, Chiba Prefecture, Japan. As a result of the field test, it was confirmed that this system supplied the one-way demands for 54.9% of total car trips and 43.9% of the user used multiple transportation modes by the common interface. In addition, this system contributed to reduce carbon dioxide emissions by sharing vehicles and using eco-friendly vehicles. The developed sharing system is expected to improve mobility by meeting more various types of traffic demand than existing car sharing systems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.12
• /
• pp.1834-1843
• /
• 2016

DVRs are the most common recording and displaying devices used for surveillance. Video compression plays a key role in DVRs for saving storage; the video compression standard, H.264/AVC, has recently become the dominant choice for DVRs. DVRs require various display modes, such as fast-forward, backward play, and pause; these are called trick modes. The implementation of precise trick mode play requires a very high decoding capability or a very intelligent scheme in order to handle the high computation complexity. The complexity is increased in many surveillance applications where more than one camera is used to monitor multiple spots or to monitor the same area using various angles. An implementation of a trick mode play and a frame buffer management scheme for the hardware-based H.264/AVC codec for multi-channel is presented in this paper. The experimental results show that exact trick mode play is possible using a standard H.264/AVC video codec with keyframe encoding feature at the expense of bitstream size increase.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.455-468
• /
• 2015

A microgrid (MG) with integrated renewable energy resources can benefit both utility companies and customers. As a result, they are attracting a great deal of attention. The control of a MG is very important for the stable operation of a MG. The droop-control method is popular since it avoids circulating currents among the converters without using any critical communication between them. Traditional droop control methods have the drawback of an inherent trade-off between power sharing and voltage and frequency regulation. An adaptive droop control method is proposed, which can operate in both the island mode and the grid-connected mode. It can also ensure smooth switching between these two modes. Furthermore, the voltage and frequency of a MG can be restored by using the proposed droop controller. Meanwhile, the active power can be dispatched appropriately in both operating modes based on the capacity or running cost of the Distributed Generators (DGs). The global information (such as the average voltage and output active power of the MG and so on) required by the proposed droop control method to restore the voltage and frequency deviations can be acquired distributedly based on the Multi Agent System (MAS). Simulation studies in PSCAD demonstrate the effectiveness of the proposed control method.

• Structural Engineering and Mechanics
• /
• v.87 no.1
• /
• pp.47-56
• /
• 2023

Any pre-existed delamination defect present during manufacturing or induce during service loading conditions in the wingskin adherend invariably shows a greater loss of structural integrity of the spar wingskin joint (SWJ). In the present study, inter-laminar delamination propagation at the critical location of the SWJ has been carried out using contact and multi-point constraint finite elements available with commercial FE software (ANSYS APDL). Strain energy release rates (SERR) based on virtual crack closure technique have been computed for evaluation of the opening (Mode-I), sliding (Mode-II) and cross sliding (Mode-III) modes of delamination by sequential release of multi point constraint elements. The variations of different modes of SERR are observed to be significant by considering varied delamination lengths, material properties of adherends and radius of curvature of the SWJ panel. The SERR rates are seen to be much different at the two pre-embedded delamination ends. This shows dissimilar delamination propagation rates. The maximum is seen to occur in the delamination front in the unstiffened region of the wingskin. The curvature geometry and material anisotropy of SWJ adherends significantly influences the SERR values. Increase in the SERR values are observed with decrease in the radius of curvature of wingskin panel, keeping its width unchanged. SWJs made with flat FRP composite adherends have superior resistance to delamination damage propagation than curved composite laminated SWJ panels. SWJ made with Boron/Epoxy (B/E) material shows greater resistance to the delamination propagation.

• Structural Engineering and Mechanics
• /
• v.84 no.4
• /
• pp.547-560
• /
• 2022

By presetting various reinforcement diameters in topology optimization with the discrete model finite element analysis, an algorithm of bidirectional evolutionary structural optimization of multi-level reinforcement diameter is presented to obtain the optimal reinforcement topologies which describe the degree of stress of different parts. The results of a comparative study on different reinforcement feasible domain demonstrate that the more angle types of reinforcement are arranged in the initial domain, the higher utilization rate of reinforcement of the optimal topology becomes. According to the nonlinear finite element analysis of some deep beam examples, the ones designed with the optimization results have a certain advantage in ultimate bearing capacity, although their failure modes are greatly affected by the reinforcement feasible domain. Furthermore, the bearing capacity can be improved when constructional reinforcements are added in the subsequent design. However the adding would change the relative magnitude of the bearing capacity between the normal and inclined section, or the relative magnitude between the flexural and shear capacity within the inclined section, which affects the failure modes of components. Meanwhile, the adding would reduce the deformation capacity of the components as well. It is suggested that the inclined reinforcement and the constructional reinforcement should be added properly to ensure a desired ductile failure mode for components.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.424-429
• /
• 2005

In this paper, the response characteristics of one to one resonance on the rectangular cantilever beam in which basic harmonic excitations are applied by nonlinear coupled differential integral equations are studied. This equations have 3-dimensional non-linearity of nonlinear inertia and nonlinear curvature. Galerkin and multi scale methods are used for theoretical approach to one to one internal resonance. Nonlinear response characteristics of 1st, 2nd, 3rd modes are measured from the experiment for basic harmonic excitation. From the experimental result, geometrical terms of nonlinearity display light spring effect and these terms play an important role in the response characteristics of low frequency modes. Dynamic behaviors in the out of plane are also studied.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1223-1234
• /
• 2018

In this paper, a new three-port multidirectional DC-DC converter is proposed for integrating an energy storage system (ESS) to a bipolar DC microgrid (BPDCMG). The proposed converter provides a voltage-balancing function for the BPDCMG and adjusts the charge of the ESS. Thanks to the multi-functional operation of the proposed converter, the conversion stages of the system are reduced. In addition, the efficiency and weight of the system are improved. Therefore, this converter has a significant capability when it comes to use in portable BPDCMGs such as electric DC ships. The converter modes are analyzed and small-signal models of the converter in each of the independent modes are extracted. Finally, comprehensive simulation studies are carried out and a BPDCMG laboratory prototype is implemented in order to verify the performance of the proposed voltage balancer using the burst mode control scheme.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.98-103
• /
• 2002

In this paper, static analysis of eddy current brake's frame, which is one of key structural components of brake system for high speed train, was performed in order to evaluate the design by computer simulation. Calculation was carried out in general for the driving modes 'braking' and 'frame in upper position(Brakes inactive)'. Several yield stress load cases and fatigue load cases were analysed for each of the driving modes. The fatigue load resulting from the Multi Body System simulation was also taken into consideration. The simulation results shows that some of structural part should be improved for more increasing reliability of frame.