• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.2
• /
• pp.108-116
• /
• 2014

With the increasing the importance of emotional quality of vehicle, the sound quality of systems with electric motor components has become increasingly important. Electric motors are used for windows, seats, sun roof, mirrors, steering columns, windshield wiper and climate control blowers, etc. In this paper, a study was conducted to identify sound quality factors that contribute to customer's satisfaction and preference of the window lift system. Jury test for subjective evaluation was carried out and sound quality index was developed. Averaged sound pressure level and sharpness were significant factors when glass moves down. Also, maximum loudness at stop section and averaged loudness were significant factor when glass moves up. Next, noise source identification was carried out using beam forming method during glass transferred section and impulsive noise at stop section. Several improvement methods were applied using the source identification result. And finally, the degree of sound quality improvement was judged using sound quality index.

• Korea-Australia Rheology Journal
• /
• v.19 no.4
• /
• pp.183-190
• /
• 2007

Injection molding is one of the most common operations in polymer processing. Good quality products are usually obtained and major post-processing treatment is not required. However, residual stresses which exist in plastic parts affect the final shape and mechanical properties after ejection. Residual stresses are caused by polymer melt flow, pressure distribution, non-uniform temperature field, and density distribution. Residual stresses are predicted in this study by numerical methods using commercially available softwares, $Hypermesh^{TM},\;Moldflow^{TM}\;and\;ABAQUS^{TM}$. Cavity filling, packing, and cooling stages are simulated to predict residual stress field right after ejection by assuming an isotropic elastic solid. Thermo-viscoelastic stress analysis is carried out to predict deformation and residual stress distribution after annealing of the part. Residual stresses are measured by the hole drilling method because the automotive part selected in this study has a complex shape. Residual stress distribution predicted by the thermal stress analysis is compared with the measurement results obtained by the hole drilling method. The molded specimen has residual stress distribution in tension, compression, and tension from the surface to the center of the part. Viscoelastic deformation of the part is predicted during annealing and the deformed geometry is compared with that measured by a three dimensional scanner. The viscoelastic stress analysis with a thermal cycle will enable us to predict long term behavior of the injection molded polymeric parts.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.51-60
• /
• 2005

This paper describes a robust control scheme for high-speed and long stroke scanning motion of high precision linear motor system consisting of linear motor, air bearing guide and position measurement system using heterodyne interferometer. Nowadays, semiconductor process and inspection of wafer or LCD need high speed and long travel length for their high throughput and extremely small velocity fluctuations or tracking errors. In order to satisfy these conditions, linear motor system are widely used because they have large thrust force and do not need motion conversion mechanisms such as ball screw, rack & pinion or capstan with which the system are burdened. However linear motors have a problem called force ripple. Force ripple deteriorates the tracking performances and makes periodic position errors. So, force ripple must be compensated. To maximize the tracking performance of linear motor system, we propose the control scheme which is composed of a robust control method, Time Delay Controller (TDC) and a feedforward control method, Zero Phase Error Tracking Control (ZPETC) for accurate tracking a given trajectory and an adaptive force ripple compensation (AFC) algorithm fur estimating and compensating force ripple. The adaptive ripple compensation is continuously refined on the basis of tracking error. Computer simulation results based on modeled parameters verify the effectiveness of the proposed control scheme for high-speed, long stroke and high precision scanning motion and show that the proposed control scheme can achieve a sup error tracking performance in comparison to conventional TDC control.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.5
• /
• pp.27-33
• /
• 2003

G-code, another name of ISO6983, has been a popular commanding language for operating machine tools. This G-code, however, limits the usage of today's fast evolving high-performance hardware. For intelligent machines, the communications between machine and CAD/CAM departments become important, but the loss of information during generating G-code makes the production department isolated. The new standard for operating machine tools, named STEP-NC is just about to be standardized as ISO14649. As this new standard stores CAD/CAM information as well as operation commands of CNC machines, and this characteristic makes this machine able to exchange information with other departments. In this research, the new CNC machine operated by STEP-NC was built and tested. Unlike other prototypes of STEP-NC milling machines, this system uses the STEP-NC file in XML file form as data input. This machine loads information from XML file and deals with XML file structure. It is possible for this machine to exchange information to other databases using XML. The STEP-NC milling machines in this research loads information from the XML file, makes tool paths for two5D features with information of STEP-NC, and machines automatically without making G-code. All software is programmed with Visual $C^{++}$, and the milling machine is built with table milling machine, step motors, and motion control board for PC that can be directly controlled by Visual $C^{++}$ commands. All software and hardware modules are independent from each other; it allows convenient substitution and expansion of the milling machine. Example 1 in ISO14649-11 having the full geometry and machining information and example 2 having only the geometry and tool information were used to test the automatic machining capability of this system.

• 대한예방의학회:학술대회논문집
• /
• 1994.02a
• /
• pp.585-595
• /
• 1994

The region of the respiratory tract where inhaled particles deposit can have important implications for the causation of local or systemic toxic effects. For most aerosols of occupational importance, respiratory tract deposition can be predicted from the aerodynamic diameter of the particles. With the advent of cascade impactors, particularly those of personal sampler size, the determination of the aerodynamic diameters of aerosols has become more common. Some limitations of cascade impactor use are well recognized (e.g., particle bounce and substrate overloading) and are generally correctable. However, two important limitations of the instruments may not be receiving adequate attention: relative humidity effects on potentially hygroscopic aerosols and the collection characteristics of fibrous aerosols as compared to their actual deposition site potential. The results of this study, when compared to results of previous controlled laboratory trials, suggest that, while potentially hygroscopic lead aerosols from lead acid battery plant operations do not appear to be affected by changes in plant environmental humidity levels, the potential - exists for significant size changes upon inhalation. Secondly, fibers were detected in aerodynamic size ranges that would be associated with deep lung deposition; however, upon microscopic examination, these same fibers would actually be predicted to deposit in the upper airways. This study suggests that the physicalchemical properties and morphological features of an aerosol should be carefully considered by industrial hygienists before cascade impactors are used in attempts to predict the effects of inhaled aerosols.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.894-896
• /
• 2003

Koh Chang Island is located near the east border of Thailand. The government of Thailand promotes the island as a model of eco-tourism spots. The Island undeveloped until recent years, is expected to change to major tourist attraction. 'Digital Koh Chang project' has thus. The main objective of this project is to monitor the environment and land use status of the island and to support its sound development. In March 2003, a field survey of this project was planned and field data were collected using both airborne and ground platforms and an ocean vessel. These data were combined with satellite data in the laboratory. This presentation is all balloon-born system field operation. A 5-meter length balloon filled with Helium gas was used, whose payload consisted of two RGB standard color digital still cameras, two directional rotating servo motors, a camera mount cradle as well as signal transmitting and receiving components. A series of aerial high-resolution digital images were rather easily obtained using this inexpensive system, making it possible to monitor intended landscape features in a specific field. Design of simple, low-cost and easily transportable flying platforms and local field surveys using them are useful for getting local ground truth data to calibrate satellite or airborne-based RS data. The design analysis to upgrade the system is further investigated.

• The Korean Journal of Applied Statistics
• /
• v.33 no.4
• /
• pp.483-497
• /
• 2020

We used a deep neural network model for the prediction of the stock prices of Kia Motors and Shinsegae as listed in the KOSPI 100. We used an emotional variable derived from online news in addition to the various technical indicators most often used. The emotional variable used as a predictor variable was generated from the average of the emotional scores for companies in the industrial group after building an emotional dictionary specific to each industrial group classified in a social network analysis. The study was conducted with various combinations of predictors and confirmed that good predictive and profitable power could be expected when jointly using technical indicators and an emotional variable based on online news by industrial groups.

• Korean Journal of Soil Science and Fertilizer
• /
• v.47 no.6
• /
• pp.425-431
• /
• 2014

Most fields in highland areas are covered with rye or hairy vetch for conservation during a fallow. However, using cover crops needs an effort to sow, and this makes top soil more vulnerable to loss due to surface disturbances. The aims of this study were to develop an automatic seeding-regulator device using a low-price, extensive-use GPS sensors and a DC motors and to evaluate a working efficiency of it after adaptation to partial tillage machine for reducing seeding effort. The amount of runoff water and soil loss was evaluated with partial tillage and simultaneous-seeding after harvesting soybean, in 17% slope lysimeters. In results, the seeding amount with the machine speed was stable between $0.5{\sim}0.8m\;s^{-1}$ of working sections. The automatic control device of seeding-rate could be enough to solve the slip problems of power selecting supply system or five four-wheel drive device. In partial tillage and simultaneous seeding, runoff water was 11.6% ($1.8m^3ha^{-1}$) of the scatter-seeding control ($15.5m^3ha^{-1}$) and soil loss was 13.2% ($7kg\;ha^{-1}$) of the scatter-seeding control ($53kg\;ha^{-1}$). These results suggest that partial tillage and simultaneous-seeding methods are very effective in decreasing work effort and soil loss of sloped land.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.6
• /
• pp.36-45
• /
• 2005

This paper addresses the application of motor current spectral analysis for the detection of rolling-element bearing damage in induction machines. We set the experimental test bed. They is composed of the normal condition bearing system, the abnormal rolling-element bearing system of 2 type induction motors with shaft deflection system by external force and a hole drilled through the outer race of the shaft end bearing of the four pole test motor. We have developed the embedded distributed fault tolerant and fault diagnosis system for industrial motor. These mechanisms are based on two 32-bit DSPs and each TMS320F2407 DSP module is checking stator current The effects on the stator current spectrum are described and related frequencies are also determined. This is an important result in the formulation of a fault detection scheme that monitors the stator currents. We utilized the FFT(Fast Fourier Transform), Wavelet analysis and averaging signal pattern by inner product tool to analyze stator current components. Especially, the analyzed results by inner product clearly illustrate that the stator signature analysis can be used to identify the presence of a bearing fault.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.14-21
• /
• 2002

This paper did the study target for modeling, characteristics analysis and harmonic reduce with the detent torque of a 4 phase and 5 phase hybrid type step motor. For this, it was attempted to derive the mathematical modeling and used the permeance method for flux field analysis. Through this analysis result, this paper acquired the detent torque of this model. To compare the characteristics analysis of phase difference with two motors structure it have obtained to derive the operating detent torque with this model. Here, 5 phase motor has known the harmonic reduce of detail torque compare with 4 phase motor. Also, that has showed to improved the step response. The analysis result has represent the effect that a fundamental component of the permeance distribution produces the average torque and that harmonic components produce the ripple torque.