• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.818-821
• /
• 2004

With a rapid development in the area of micro and ultra precision technology, the micro surface machining of small size parts are explosively increased. Especially, to improve efficiency of various beams in lens and reflector, non-rotational symmetric form and several mm level heights changeable surface can be machined at a time. These geometric complex 3D surface cannot be machined by general short stroke FTS. The long stroke FTS if firmly needed to move directly several mm and have nm level positioning accuracy for the complex surface form. The long stroke FTS used linear motors to drive moving unit long and fine, aero static bearings to decrease friction and moving errors in guide way, optical linear scale with nm level resolution to measure position of FTS. Furthermore, to increase the performance of acceleration of FTS, the light material, such as AL is used for the structure and the high stiffness box type structure is selected. In this paper, the genetic algorithm approach is described to determine a set of design parameters for auto tuning. The authors have attempted to model the design problem with the objective of minimizing the error, such as variable pattern change. This method can give the better alternative than existing other method.

• Journal of Power Electronics
• /
• v.8 no.3
• /
• pp.228-238
• /
• 2008

Many induction motor broken bar diagnosis methods are based on evaluating special components in machine signals spectrums. Current, power, flux, etc are among these signals. Frequencies related to a broken rotor fault are slip dependent, therefore, correct diagnosis of fault - especially when obtrusive frequency components are present - depends on accurate determination of motor velocity and slip. The traditional methods typically require several sensors that should be pre-installed in some cases. This paper presents a diagnosis method based on only a vibration sensor. Motor velocity oscillation due to a broken rotor causes frequency components at twice slip frequency difference around speed frequency in vibration spectrum. Speed frequency and its harmonics as well as twice supply frequency, can easily and accurately be found in a vibration spectrum, therefore th motor slip can be computed. Now components related to rotor fault can be found. It is shown that a trained neural network - as a substitute for an expert person - can easily categorize the existence and the severity of a fault according to the features extracted from the presented method. This method requires no information about th motor internal and has been able to diagnose correctly in all the laboratory tests.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.209-214
• /
• 2002

We developed a small, remote controlled observation ship that can reduce the cost of gathering data for marine and coastal environments. The control system is composed of three microprocessors, one is for overall mission control, another for control of propulsion motors, and the other for sensor operation. For communication system, we adopt direct and indirect methods based on the wireless modem of commercial cellular telephone. The former is a direct communication between the modems of the ship and the server, and the latter is an indirect communication via internet between the ship and the server. The performance of the ship is demonstrated with the results produced by sets of experiments.

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.2
• /
• pp.134-147
• /
• 2015

This study proposes a method to determine the effective angular velocity of each motor of a specific four-rows tracked vehicle (FRTV) in order to follow a given turning radius. The configuration of the four-rows tracked vehicle is introduced, and its dynamics analysis model is built using the DAFUL commercial software. The soil has been assumed to be hard ground, and the friction force between the ground and the tracked links is calculated using the Coulomb friction model. This paper uses a simulation to show that the error in the position increased with respect to the angle of the curvatures, so a method is proposed to compensate for the error in the motion of the motors. Various simulations are then carried out to verify the proposed formulation. The effects of the soil characteristics and the driving velocity will be further investigated in future studies.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.3
• /
• pp.221-226
• /
• 2016

An attitude controller for a 6-DOF hovering autonomous underwater vehicle (HAUV) is implemented. We add a vertical thruster, an underwater camera, a wireless communication device, and a DVL to the HAUV that was developed a year ago. The HAUV is composed of 5 thrusters, 2 servo-motors, and 4 apparatus parts. Two rotating thrusters control the surge, heave, and roll of the vehicle. The vertical thruster controls the pitch, and two horizontal thrusters control the sway and yaw of the vehicle. The HAUV’s movement in each direction is controlled by 6 PID controllers. Each PID controller controls the propulsive force and angle of a thruster. In a horizontal and vertical movement experiment, we showed the feasibility of the proposed controller by maintaining a given depth and heading angle of the HAUV.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1321-1328
• /
• 2009

In this paper, an electromagnetic force driving actuator (EMFA) and three-link mechanism are proposed as a driving mechanism and connection device for low voltage air circuit breaker (ACB). As the result of dynamic characteristic analysis, the actuator and link mechanism are designed from the simulation and manufactured. The magneitc field of the EMFA is analyzed using the finite element method (FEM). The dynamic characteristic analysis with calculation of the circuit equation and kinetical equation is performed by the time difference method (TDM). Also, the result of the analysis is verified through the experiment of the fabrication model. In this paper, the EMFA size is smaller than the actuator for high voltage circuit breaker. Thus, the dynamic characteristic is analyzed with end-winding inductance that is calculated by the same method which is applied on the circle type end-winding of motors. The designed model for 1600 ampere-frame ACB and the three-link mechanism for connecting contact part with actuating part are manufactured. It is confirmed that the three-link mechanism is possible for improving the circuit breaker efficiency and reducing the size of the EMFA. It is proved that the improved 2-D analysis is more accurate than established method.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.243-244
• /
• 2008

In this paper proposed the solar tracking system to use a fuzzy based on PC in order to increase an output of the PV array. The solar tracking system operated two DC motors driving by signal of photo sensor. The control of dual axes is not an easy task due to nonlinear dynamics and unavailability of the parameters. The fuzzy control made a nonlinear dynamics to well perform and had a robust and highly efficient characteristic about a parameter variable as well as a nonlinear characteristic. In this paper designed a fuzzy controller for improving output of PV array and evaluated comparison with efficient of conventional PI controller. The data which were obtained by experiment were able to show a validity of the proposed controller.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.240-248
• /
• 2009

An approach to control the position for an interior permanent magnet synchronous motor (IPMSM) based on an adaptive integral binary observer is described. The binary controller with a binary observer is composed of a main loop regulator and an auxiliary loop regulator. One of its key features is that it alleviates chatter in the constant boundary layer. However, steady state estimation accuracy and robustness are dependent upon the thickness of the constant boundary layer. In order to improve the steady state performance of the binary observer and eliminate the chattering problem of the constant boundary layer, a new binary observer is formed by adding extra integral dynamics to the existing switching hyperplane equation. Also, the proposed adaptive integral binary observer applies an adaptive scheme because the parameters of the dynamic equations such as the machine inertia and the viscosity friction coefficient are not well known. Furthermore, these values can typically be easily changed during normal operation. However, the proposed observer can overcome the problems caused by using the dynamic equations, and the rotor position estimation is constructed by integrating the rotor speed estimated with a Lyapunov function. Experimental results obtained using the proposed algorithm are presented to demonstrate the effectiveness of the approach.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.4
• /
• pp.121-129
• /
• 2008

This paper deals with the design of BLDC motor replacing ferrite magnet with rare earth magnet. Electric machinery system using ferrite magnet motor is already widespread in large numbers. Electrical appliance makers have a tendency to adhere to existing system using ferrite magnet motors because of redesigning the whole system. This paper designs the rare earth magnet motor untouching the external system dimension and motor outer size. To do the design simply, finite element package is used iteratively To reduce the cogging torque effect and magnetic saturation, stator yoke shape and the groove of the end face of yoke are redesigned.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.359-362
• /
• 2009

Optimal efficiency control of synchronous reluctance motor(SynRM) is very important in the sense of energy saving and conservation of natural environment because the efficiency of the SynRM is generally lower than that of other types of AC motors. This paper is proposed a novel efficiency optimization control of SynRM considering iron loss using multi adaptive fuzzy learning controller(AFLC). The optimal current ratio between torque current and exciting current is analytically derived to drive SynRM at maximum efficiency. This paper is proposed an efficiency optimization control for the SynRM which minimizes the copper and iron losses. There exists a variety of combinations of d and q-axis current which provide a specific motor torque. The objective of the efficiency optimization control is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. The control performance of the proposed controller is evaluated by analysis for various operating conditions. Analysis results are presented to show the validity of the proposed algorithm.