• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.370-374
• /
• 1991

This paper presents a static circuit model for static ant dynamic simulation of induction motors and identification of motor parameters. Instead of usual T-circuits, equivalent ${\pi}$-circuit has been proposed so that power Inputs into motor terminals can very easily calculated with very well known load flow method. It has been shown that, with wide range variation of applied voltage and frequency, successful static simulations can be performed and further the proposed static model can be used to simulate dynamic characteristics. Finally it is shown also that motor parameters can easily be identified based on the proposed static circuit.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.286-291
• /
• 1991

Most of the failures of rotating machine are stator coil insulation failures. The insulation diagnostic testing for high voltage motors and generators are only megger test and P. I Test which is applied DC voltage until now. But it was impossible to judge insulation deterioration status of high voltage rotating machinery by above testing. In other words, even though the megger measurement values are fairly high, they used to be failed from time to time. Therefore in order to excute reliable and detailed diagnosis of insulation deterioration for rotating machinery, the tangent delta test, the alternating current test and the partial discharge test shall be applied to the insulation diagnostic testing on site.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.605-610
• /
• 1991

In inverter system for driving induction motor, the output harmonics are hamrful in induction motor drive because it leads to ripple torque and induction interference. For electrical drives using PWM(Pulsewidth Modulation) inverters and ac motors, the methods for efficiency optimal control have been developed. In this paper, two different PWM methods for inverter and voltage control technique are described. In order to reduce or minimize losses, various forms of PWM strategy such as, PM (Positive Modulation) and NM (Negative Modulation) are discussed. The results show the feasibility of obtaining practically sinusoidal output waveforms which are highly desirable in most inverter application.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.949-950
• /
• 2011

There are various ways of optimizing rotor design of Interior Permanent Magnet Synchronous Motors(IPMSM). In this paper, the best optimized design value was found by varying the Bridge thickness of PM in the rotor and changing Rib. The set design values were torque, 5 harmonics, 7 harmonics, and safety factor. Also, in order to make practical design value easily and quickly for optimization, Box-Behnken of Response Surface Method(RSM) method was used. Therefore, IPMSM resulted an optimized design model with high torque, low harmonics, and constant value of safety factor.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.967-968
• /
• 2011

직립 기동 영구자석 동기 전동기(Line-Start Permanet Magnet Synchronous Motor : LSPM)는 기존 3상 유도기에 비해 높은 효율과 역율을 가진다. 또한 제어기를 사용하지 않고 기동 할 수 있다는 장점 때문에 펌프나 팬 등에 단순한 구동원에 적용 할 수 있는 전동기이다. 구조는 유도기와 달리 영구자석이 매입되기 때문에 이에 따라 영구자석의 위치와 크기에 따라 모터의 특성이 변화 한다. 본 논문에서는 실험 계획법과 FEM 유한 요소법을 이용하여 영구자석의 크기는 고정되어 있는 상태에서 영구자석 슬롯의 모양만을 설계 인자에 따라 해석하였다. 그리고 해석을 통한 결과를 비교 분석하여 직립기동 영구자석 동기 전동기의 효율과 토크특성을 개선하고자한다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1141-1142
• /
• 2011

An electrical vehicle (EV) is a huge issue in the automotive industry. The EV have many electrical units: electric motors, batteries, converters, ets. The DC power distribution system (PDS) is essential for the EV. The DC PDS offers many advantages. However, multiple loads in the DC PDS may affect the severe instability on the DC bus voltage. Therefore, a voltage bus conditioner (VBC) may use the DC PDS. The VBC is used to mitigate the voltage transient on the bus. In this paper, sliding mode controller (SMC) is designed for the VBC of DC PDS in the EV. The simulation results by PISM simulation package are presented for validating the proposed control technique.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.814-815
• /
• 2011

A surfaced permanent magnet spherical motor is capable of operating as three degree of freedom that used for the joints of the robot's arm, leg, and eyes. Ongoing research like new concept is essential part of motor field, it will make a great contribution in the future the overall portion of the motor, is becoming expected. The author analysis torque characteristics in spherical motor with state of rotating and positioning. And future design direction is smaller motors with equivalent or higher output. Solutions as torque and efficiency improvements are selecting the core with special processing type like powder metallurgy materials. Their special characteristic is high permeability and low eddy current losses at high speed, so improved the torque and efficiency.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1766-1767
• /
• 2011

본 논문에서는 기존의 proportional-integral-derivative (PID) 제어기의 이득조정과정에서 linear quadratic regulator(LQR)을 이용하여 이득조정을 하는 방법을 제안한다. 제안된 제어기의 이득은 LQR의 수식으로 표현되어지며 Matlab/simulink을 이용한 모의실험을 통해 위치프로파일에 대한 위치추종오차의 성능이 평가되어진다.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.94-103
• /
• 2011

This paper presents a novel bearingless switched reluctance motor (BLSRM) with decoupled torque and suspending stator poles. BLSRM is different from conventional bearingless switched reluctance motors (SRMs) because its suspending poles are separated from the torque poles. Perpendicularly placed suspending poles are designed to produce a continuous radial force to suspend the rotor. Due to the independent suspending and torque poles, BLSRM produces a suspending force with excellent linearity according to the rotor position and independent characteristics of the torque current. The air-gap is easier to control than in conventional SRMs with their linear and independent characteristics. Furthermore, to verify the proposed structure, a mathematical model for the suspending force is derived. Finite element analysis is also employed to compare BLSRM and conventional SRMs expressions of suspending force. A prototype motoris designed and manufactured to verify the effectiveness of the proposed bearingless structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2173-2178
• /
• 2010

The magnetization directions of a polar magnetized ferrite bonded magnet are analyzed by finite element method (FEM). The influence of the width of SmCo magnets for magnetic field generation is investigated. The surface flux densities of the polar anisotropic magnets are analyzed and compared according to the pole number and thickness of the magnets. And the electromotive force (EMF) values of brushless DC motors with the magnets are investigated. The validity of the analysis method is verified by comparing the analyzed results with measured ones.