• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.67-68
• /
• 2015

본 논문은 폐루프 고피나스 자속관측기의 P/PI모드를 전환하여 전환점부근 저속에서 모터상수 변동에도 강인한 센서리스 벡터제어가 가능한 전환기법을 제안하였다.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.49-50
• /
• 2016

본 논문에서는 BLDC 모터의 홀 센서의 정렬 오차를 검출하고 보상하는 기법을 제안한다. 합성된 홀 센서 신호를 이용하여 고조파 분석을 수행하여 기본파 성분의 크기를 획득한다. 오차가 없는 경우의 기본파 성분의 크기와 비교하여 정렬 오차각을 검출하고 보상한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.31.2-31
• /
• 2001

A real-time control strategy is presented for plasma control Rather than in-situ plasma variables, this is based on realtime measurements of two electrical positions that correspond to two match motors. Using the rf match monitor system, the positions were collected. The process of impedance matching was identified with variations in process factors, including rf power, pressure, and O$_2$ flow rate. A state-space model was obtained basing on autoregressive moving average model. For this model, a linear quadratic regulator was designed and applied. Simulation results revealed that match positions could accurately be regulated to follow certain positions arbitrarily chosen.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.114-122
• /
• 2000

Bullet impact tests for solid rocket motor were performed and its results wert described. Two motors were made of composite and steel for case material, respectively and their reactions to the bullet impact were compared. Throughout the tests it had been tried to setup the procedure of bullet impact test and criteria of the judgment for the reactions.

• Proceedings of the PSK Conference
• /
• 2003.04a
• /
• pp.164.1-164.1
• /
• 2003

Diesel motors exhaust particulate material. which is known to be mutagenic, has caused heavy air pollution. PM 2.5 diesel exhaust of vehicle was collected using a high-volume sample equipped with a cascade impact. The crude extract was fractionated according to EPA recommended procedure into seven fractions by acid-base partitioning and silica gel column chromatography. (omitted)

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.441-442
• /
• 2020

본 논문에서는 2상 하이브리드 스테핑 모터의 디텐트 토크 보상 기법을 제안하였다. 2상 하이브리드 스테핑 모터의 회전자 좌표계 d,q축 전압 방정식 및 토크 식으로부터 지령 토크 발생을 위해 필요한 d,q축 전류를 지령으로 사용하며, 디텐트 토크로 인해 발생하는 속도 리플을 제거하기 위해 리플 크기를 추출하여 전류지령에 보상하였다. Matlab/Simulink를 이용한 2상 하이브리드 스테핑 모터 구동 시뮬레이션을 통해 제안된 기법의 유효성을 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.437-438
• /
• 2020

본 논문에서는 2상 하이브리드 스테핑 모터 구동을 위해 H-bridge 회로 또는 3상 인버터를 이용하는 경우의 출력 성능을 비교 검토하였다. 벡터 제어로 구동하는 경우 2상 하이브리드 스테핑 모터의 상전압, 상전류의 THD(Total Harmonic Distortion)과 출력 토크 리플을 분석하였으며, 이를 위해 Matlab/Simulink를 이용한 150W급 스테핑 모터의 시뮬레이션을 수행하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.224-224
• /
• 2012

For decades, carbon fiber has expanded their application fields from reinforced composites to energy storage and transfer technologies such as electrodes for super-capacitors and lithium ion batteries and gas diffusion layers for proton exchange membrane fuel cell. Especially in fuel cell, water repellency of gas diffusion layer has become very important property for preventing flooding which is induced by condensed water could damage the fuel cell performance. In this work, we fabricated superhydrophobic network of carbon fiber with high aspect ratio hair-like nanostructure by preferential oxygen plasma etching. Superhydrophobic carbon fiber surfaces were achieved by hydrophobic material coating with a siloxane-based hydrocarbon film, which increased the water contact angle from $147^{\circ}$ to $163^{\circ}$ and decreased the contact angle hysteresis from $71^{\circ}$ to below $5^{\circ}$, sufficient to cause droplet roll-off from the surface in millimeter scale water droplet deposition test. Also, we have explored that the condensation behavior (nucleation and growth) of water droplet on the superhydrophobic carbon fiber were significantly retarded due to the high-aspect-ratio nanostructures under super-saturated vapor conditions. It is implied that superhydrophobic carbon fiber can provide a passage for vapor or gas flow in wet environments such as a gas diffusion layer requiring the effective water removal in the operation of proton exchange membrane fuel cell. Moreover, such nanostructuring of carbon-based materials can be extended to carbon fiber, carbon black or carbon films for applications as a cathode in lithium batteries or carbon fiber composites.

• Journal of IKEEE
• /
• v.18 no.3
• /
• pp.376-382
• /
• 2014

In this paper, we propose a advanced attitude PID controller and sensor fusion method robust to the vibration of the quadcopter unmanned air vehicle using four BLDC motors. When the gyro sensor and acceleration sensor are fused, a complementary filter is designed to ignore the vibrations generated by the motors and to complement the drawbacks. As a result, we obtain accurate results than using each sensor. Also, it is possible to obtain a low delay results in robust to vibration than the low-pass filter or moving average filter, which is generally used for quadcopter. And we improved D controller, which have being used for attitude control of quadcopter, to quadcopter using gyro sensor. it was confirmed that the attitude is stabilized and error is reduced By using gyro sensor output instead of variation of estimated angle in D control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.232-239
• /
• 2013

This paper proposes an improved stator flux estimator through ensuring conventional PLPF to act as a pure integrator for sensorless control of induction motors. Conventional PLPF uses the estimated synchronous speed as a cut-off frequency and has the gain and phase compensators. The gain and phase compensators are determined on the assumption that the estimated synchronous angular speed is coincident with the real speed. Therefore, if the synchronous angular speed is not same as the real speed, the gain and phase compensation will not be appropriate. To overcome the problem of conventional PLPF, this paper analyzes the relationship between the synchronous speed error and the phase lag error of the stator flux. Based on the analysis, this paper proposes the synchronous speed error compensation scheme. To achieve a start-up without speed sensor, the current model is used as the stator flux estimator at the standstill. When the motor starts up, the current model should be switched into the voltage model. So a stable transition between the voltage model and the current model is required. This paper proposes the simple transition method which determines the initial values of the voltage model and the current model at the transition moment. The validity of the proposed schemes is proved through the simulation results and the experimental results.