• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.400-402
• /
• 1996

The paper describes the control strategy and hardware design for forced commutation cycloconverter which was developed for ac servo motor drive application of vector control. 12-pulse cycloconverter is used to investigate experimentally the performance of an induction motor drive system. The cycloconverter has the facility for continuous control of both the frequency and magnitude of the output voltage to keep a constant flux in the induction motors.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.292-295
• /
• 2003

전기기관차에 사용되는 6-병렬 구조의 견인용 직류전동기 접지개소를 실시간으로 검출하기 위하여 병렬회로가 갖는 등가 임피던스 변화를 이용한 새로운 접지검출 방법에 대하여 제안한다. 기존 보호회로가 접지 릴레이를 사용하여 접지의 발생 유무만을 인식한 것에 비하여 제안된 방법에서는 각 직류전동기의 회전자 및 계자의 접지를 선별적으로 구분하는 것이 가능한 특징을 갖는다. 제안된 검출방법의 타당성 조사를 위하여 병렬견인구동회로에 대한 컴퓨터 시뮬레이션을 수행하였다.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.82-86
• /
• 1990

A camera type optical bench system equipped with a lens collimator and an image analyzer is fabricated to measure the equivalent focal length and distortion of lenses. This system is automatized by the computer which controls stepping motors. A nodal slide optical bench system equipped with an off axis reflective collimator is fabricated and improved by using rotating arms and air bearing system. distortion measurement on a wide angle lens using the camera method and the nodal slide method is reported. Defocusing error in the distortion measurement with the nodal slide optical bench is analyzed and improved by iteration method to search the correct image point.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.177-181
• /
• 1997

In the speed control system of motors using the low resolution rotary encoder, the period of encoder pulse becomes longer than the sampling time for speed control in the range of very low speed. Therefore, it is difficult to obtain accurate speed information. In this paper, the speed estimating method at the very low speed region using reduced order torque observer, which has been widely used, is examined. The results of simulation show that the characteristics of the speed control at the very low speed region is improved by using the reduced order torque observer.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.152-155
• /
• 1997

This thesis proposed a speed control system for induction motors robust to variations in torque and parameters by feedforward compensating the current portion of load torque, adding a load torque observer to the conventional PI controller in the indirect vector controlled induction motor system. In conclusion, this thesis demonstrate the improved transient characteristic to variations in reference speed and load torque, compared to the conventional PI control method, by means of the feedworward control of the estimated load torque.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.331-335
• /
• 2001

This paper presents the self-commissioning for surface-mounted permanent magnet synchronous motor. The proposed strategy executes three tests with a standard inverter drive system. To do this, synchronous d-q axes currents are appropriately controlled for each test. From the three tests, armature resistance, armature inductance, equivalent iron loss resistance, and emf coefficient are identified automatically. The validity of the proposed strategy is confirmed by experimental results.

• Tribology and Lubricants
• /
• v.11 no.2
• /
• pp.63-70
• /
• 1995

The analytical design method of gerotor profile, based on an envelope of a family of curves, is proposed. Analysis to calculate the flow rate and the torque capacity of a gerotor set are presented. The influence of the circular tooth radius and the amount of eccentricity on the configuration of a gerotor has been explored in this paper. The variation of the inlet volume and the fluctuation of the generated torque are also analyzed.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.229-231
• /
• 2006

본 논문은 매입형 영구자석 전동기의 고정자 전압방정식으로부터 관측기를 구성하고, 회전자 좌표계상에서 추정속도를 구하여 퍼지제어기를 이용한 속도 보상 센서리스제어를 수행하였다. 전동기의 전압방정식과 퍼지제어기만을 이용하기 때문에 전동기의 기계적 방정식에서 발생하는 기계적 제정수의 영향에 대해 강인한 특성을 갖는다. 제안된 알고리즘의 타당성과 강인함은 실제 구동을 통하여 증명한다.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.426-428
• /
• 1994

The effect of the snubber circuit is to control the voltage spikes applied across switching devices during turn-off. This paper describes a loss-less snubber of a converter for Switched Reluctance Motors. The feasibility of the snubber circuitry is experimentally verified using a laboratory prototype.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.576-580
• /
• 2000

This paper describes about the field test of IGBT VVVF inverter for the propulsion system. The 1650kV class IGBT VVVF inverter has been developed. Therefore the field test is performed in SMG 6 Line to confirm its the reliability and performance. The train consists of 4M4T and the electrical equipment for field test are as follows : VVVF inverter 4 sets 16 traction motors and 3 SIVs The propulsion system which have the excellent acceleration/deceleration and the jerk chracteristics as well as starting ability on slope are taken through the field test.