• The Journal of Korean Medicine
• /
• v.24 no.4
• /
• pp.92-101
• /
• 2003

Background ＆ Aims : The aim of this study was to investigate the change of dominant power with observation of gastric myoelectrical activity and its parameter linkage in electrogastrography. Methods : Electrogastrography was performed on a total of 123 subjects (113 patients with functional dyspepsia, 10 healthy controls) for 30 min in fasting state and 50 min in postprandial state. Average myoelectrical activity per frequency and accumulated electrical activity of 5 min duration in each bradygastria, normogastria, and tachygastria were measured at the moment of frequency switchover of slow wave. Assumed parameter linkages were also investigated among dominant frequency, ％ of normal regularity, and dominant power (or power ratio). Results : Average myoelectrical activity per frequency was highest in bradygastria (mean 1.10-1.47 Volt/s), next highest in normogastria (mean 0.50-0.82 Volt/s), and lowest in tachygastria (mean 0.44-0.47 Volt/s). Average accumulated myoelectrical activity was highest in normogastria (mean 114.90-126.29 Volt/ss), next highest in tachygastria (mean 71.02-90.00 Volt/ss), and lowest in bradygastria (mean 12.93-51.94 Volt/ss). Significance of parameter linkages were noted in dominant frequency (p< 0.01) and in ％ of normal regularity (p< 0.01), but not in dominant power in case of frequency shift from bradygastria to normogastria (p=0.376). Conclusion : Dominant power is not a parameter that reflects the gastric myoelectrical activity related with only gastric contraction. Bradygastric dominant power does not follow the inter-parameter linkage of electrogastrography for gastric motility assessment.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.2
• /
• pp.155-165
• /
• 2010

The purpose of this study was to analyze kinematic quantitative factors required of a forehand counter drive in table tennis through 3-D analysis. Four national table tennis players participated in this study. The mean of elapsed time for total drive motion was $1.009{\pm}0.23\;s$. At the phase of impact B1 was the fastest as 0.075 s. This may affect efficiency in the initial velocity and spin of the ball by making a powerful counter drive. The pattern of center of mass showed that it moved back and returned to where it was then moved forward. At the back swing, lower stance made wide base of support and a stronger and safer stance. It may help increasing the ball spin. Angle of the elbow was extended up to $110.75{\pm}1.25^{\circ}$ at the back swing and the angle decreased by $93.75{\pm}3.51^{\circ}$ at impact. Decreased rotation range of swinging arm increased linear velocity of racket-head and impulse on the ball. Eventually it led more spin to the ball and maximized the ball speed. Angle of knee joint decreased from ready position to back swing, then increased from the moment of the impact and decreased at the follow thorough. The velocity of racket-head was the fastest at impact of phase 2. Horizontal velocity was $7796.5{\pm}362\;mm/s$ and vertical velocity was $4589.4{\pm}298.4\;mm/s$ at the moment. It may help increase the speed and spin of the ball in a moment. The means of each ground reaction force result showed maximum at the back swing(E2) except A2. Vertical ground reaction force means suggest that all males and females showed maximum vertical power(E2), The maximum power of means was $499.7{\pm}38.8\;N$ for male players and $519.5{\pm}136.7\;N$ for female players.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.7
• /
• pp.767-773
• /
• 2014

The carrier-to-noise power ratio is a key parameter for determining the reliability of PVT (Position, Velocity, and Time) solutions which are obtained by a GNSS (Global Navigation Satellite System) receiver. It is also used for locking a tracking loop, deciding the re-acquisition process, and processing advanced navigation in the receiver subsystem. The representative carrier-to-noise power ratio estimation schemes are the narrowband-wideband power ratio method (NW), the MM (Moment Method), and Beaulieu's method (BL). The NW scheme is the most classical one for commercial GNSS receivers. It is often used as an authoritative benchmark for assessing carrier-to-noise power estimation schemes. The MM scheme is the least biased solution among them, and the BL scheme is a simpler scheme than the MM scheme. This paper focuses on the less biased estimation with low complexity when the residual phase noise remains, then proposes a novel carrier-to-noise power ratio estimation scheme with low complexity for GNSS receivers. The asymptotic bias of the proposed scheme is derived and compared with others, and the simulation results demonstrate that the complexity of the proposed scheme is lowest among them, while the estimation performance of the proposed scheme is similar to those of the BL and MM schemes in normal and high gained reception environments.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.5
• /
• pp.185-190
• /
• 2016

The high-power 6.6 kV XLPE (or CV) cables at Korean electric power stations have been in operation for the last 40 years. Most of the XLPE cables starts deteriorating in 6-8 years from the operating instant of time, some cables may be breakdown at any moment even though they were installed in recent years, causing, huge socioeconomic losses. In order to prevent unexpected cable accident, the operating status of power cables should be monitored in regularly, timely bases. We have invented a device in order to systematically monitor and prevent an abrupt accidents of high-power cables in operation at power station. It has been installed at Korean Western Power Co. Ltd. at Taean, and operating normally for the last 4 years. In this paper, we introduce the functions and operating principles of the measuring device, and present the relationship between humidity and insulation status of XLPE cables for the load of electric turbine generator.

• Composites Research
• /
• v.37 no.2
• /
• pp.101-107
• /
• 2024

Demand for submarine cable is increasing due to advances in submarine power transmission technology and submarine cable manufacturing technology. Submarine cable use various types of protective equipment to prevent problems such as high maintenance costs in the event of cable damage and power outages during maintenance periods. Among them, flexible protection tube is a representative protective equipment to protect cables and respond to external forces such as waves and current. The flexible protection tube is made of polyurethane 85A hyperelastic material, so the calculation of mechanical behavior is carried out using mechanical properties based on experimental results. In this study, a study was conducted to determine the bending performance and tensile performance of flexible protection tube through analytical methods. The physical properties obtained through the multiaxial tensile test of polyurethane 85A were used for the analysis. Bending and tensile performance were determined for the maximum bending moment standard of 15 kN·m and the tensile load standard of 50 kN. As a result, it was confirmed that when the maximum bending moment of 15 kN·m of the flexible protection tube occurred, the bending performance of the MBR was secured at 13 m and when a tensile load of 50 kN, it was applied the maximum vertical displacement was 968 mm, confirming that the tensile performance was secured.

• 전자공학회논문지 IE
• /
• v.43 no.1
• /
• pp.32-38
• /
• 2006

When induction motor moves, power quality decline of line is risen seriously because provoking voltage drop the moment to system power supply by excessive moving current as well as power-factor drop in case drive by light-load because current reaches in 6 times $\sim$ 8 times of rated current. In this paper, a modeling did an distribution system 13 bus type model and induction machine load presents in IEEE using a PSCAD/EMTDE package, and it displayed an accident conspiracy and a compensating factor of DSTATCOM through simulation show.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.408-410
• /
• 2006

To chase maximum power point at every moment under a conventional MPPT control method, a voltage and current coming out from PV-cell are needed to be feedbacked. So, the structure of control circuit becomes so complex and the MPPT control is in risk of control failure. In the newly developed control method, the current flowing into SPE cell is the only one considerable factor. So, the structure of control circuit becomes simple and the manufacturing cost of the control device decreases. Especially, in case of a huge system of PV-SPE system, because the voltage coming out from PV-cell is not needed to be feed backed, this system can be operated much more safely. In this paper, the PV-SPE system was actually manufactured based on the simulation model of PSCAD/EMTDC program and the results tested were shown. Authors are sure that it is the most useful method to maximize power from PV to SPE with only a feedback of SPE input current.

• Journal of Korea Multimedia Society
• /
• v.19 no.5
• /
• pp.901-909
• /
• 2016

Unprecedented attention is being given to Smart Grid, Micro Grid and Internet of Things (IoT) in the Republic of Korea recently but such systems' effect is not well experienced by the market since they require additional and costly reforms for the existing household electrical system where adaptive communication platforms are needed. As such platforms, both wireless and wire communication technologies are being considered at the moment. Usually, they include WiFi, Zigbee technologies and the latter, LAN technology. However, communication speed decline due to signal attenuation and interference during wireless communications are considered to be the major problem and the extra works involving time and costs for the LAN system construction can be another demerit. Therefore, in this paper, we have introduced a Power Line Communication-based Smart Outlet System Expandable at Home to complement these disadvantages. Proposed IoT system involves Power Line Communication (PLC) technology which is essential to constructing a Smart Grid.

• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.9-12
• /
• 1999

This paper presents the development of a control architecture for the autonomous underwater vehicle (AUV) with VARIVEC (variable vector) propeller. Moreover this paper also describes the new technique of controlling the servomotors using the Field Programmable Gate Array (FPGA). The AUVs are being currently used fur various work assignments. For the daily measuring task, conventional AUV are too large and too heavy. A small AUV will be necessary for efficient exploration and investigation of a wide range of a sea. AUVs are in the phase of research and development at present and there are still many problems to be solved such as power resources and underwater data transmission. Further, another important task is to make them smaller and lighter for excellent maneuverability and low power. Our goal is to develop a compact and light AUV having the intelligent capabilities. We employed the VARIVEC propeller system utilizing the radio control helicopter elements, which are swash plate and DC servomotors. The VARIVEC propeller can generate six components including thrust, lateral force and moment by changing periodically the blade angle of the propeller during one revolution. It is possible to reduce the number of propellers, mechanism and hence power sources. Our control tests were carried out in an anechoic tank which suppress the reflecting effects of the wall surface. We tested the developed AUV with required performance. Experimental results indicate the effectiveness of our approach. Control of VARIVEC propeller was realized without any difficulty.

• Advances in Computational Design
• /
• v.2 no.3
• /
• pp.211-223
• /
• 2017

This research presented a numerical and experimental study on the seismic performance of first-generation base-isolated and fixed-base nuclear power plants (NPP). Three types of the base isolation system were applied to rehabilitate the first-generation nuclear power plants: frictional pendulum (FP), high-damping rubber (HDR) and lead-rubber (LR) base isolation. Also, an Excel program was proposed for the design of the abovementioned base isolators in accordance with UBC 97 and the Japan Society of Base Isolation Regulation. The seismic assessment was performed using the pushover and nonlinear time history analysis methods in accordance with the FEMA 356 regulation. To validate the adequacy of the proposed design procedure, two small-scale NPPs were constructed at Universiti Teknologi Malaysia's structural laboratory and subjected to a pushover test for two different base conditions, fixed and HDR-isolated base. The results showed that base-isolated structures achieved adequate seismic performance compared with the fixed-base one, and all three isolators led to a significant reduction in the containment's tension, overturning moment and base shear.