• 산업경영시스템학회지
• /
• 제28권1호
• /
• pp.24-31
• /
• 2005

The outsole mold of the shoes has been manufactured using electro-discharge machining by graphite electrode or using casting etc. The study is concerned with the pattern design for the outsole of shoes by CAD, the modeling and the generation of NC data by CAM system and the machining by CNC machining center. The ball end mill and the engraving cutter is used as cutter and the cutting conditions are adjusted according to the shapes and sizes of the cutter and part in cutting. The method showed the possibility coping with the rapid change of shoes industry and proposed the possibility for higher productivity and quality on mold-manufacturing of shoes outsole.

• 한국주조공학회지
• /
• 제2권2호
• /
• pp.18-30
• /
• 1982

For the purpose of improving the casting yields of ductile iron castings, the casting conditions for riserlese design were investigated with 150mm cube. As the important casting conditions, chemical composition, pouring temperature, mold rigidity and cooling rate were confirmed. 1. We could obtain the sound castings with the hypereutectic ductile iron. 2. In order to reduce liquid contraction, the pouring temperature should be low as much as possible 3. We could obtain the sound castings through using the rigid mold without mold cavity deformation 4. The modulus of the castings should be 2.5cm one or larger.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 금형가공,미세가공,플라스틱가공 공동 심포지엄
• /
• pp.141-146
• /
• 2005

In the present study, the characteristic of warpage and flow balance for family mould, which is able to mold parts with different shapes in a mold, is considered. To obtain an optimal gate and runner system, plastic injection molding analysis with commercial code is performed. Design and manufacturing of family mould is then carried out on the basis of this computer aided engineering result. Flow balance and warpage comparisons between experiment and numerical analysis give good agreement with each other. However, it was shown that results of warpage measured by CMM was about $20\~55\%$ lower than those of numerical analysis.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.474-479
• /
• 2005

Experimental and theoretical studies of internal cavity pressure during injection molding of a spiral tube cavity were carried out. The frozen layer thickness and the evolution of internal cavity pressure were calculated using a commercial software (C-MOLD). The evolution of the internal cavity pressure was recorded during injection molding of polystyrene into a spiral tube mold. To explain the differences observed between the calculated and measured internal cavity pressure, a pressure correction factor (PCF) was introduced based on the plane stress theory. This factor was determined by analyzing the stress state in the melt and calculating the frozen layer thickness near the mold wall. The corrected and experimental pressures have been compared to validate the applicability of the pressure correction factor.

• 대한금속재료학회지
• /
• 제50권2호
• /
• pp.129-135
• /
• 2012

High speed casting technology is an attractive method to increase the productivity of continuous casting. However, high speed casting causes flow instability of molten steel in a mold. In this study, Large Eddy Simulation (LES) has been performed to identify the characteristics of mold flow for various shapes of submerged entry nozzles. The LES code has been newly developed to efficiently compute the two-phase flow by using the Fractional Step Method (FSM) combined with the Volume of Fluid (VOF) method. The Immersed Boundary Method was used to implement the shape of the submerged entry nozzle. Three cases of discharge angle of the submerged entry nozzle were computed and compared. The current results shed light on improving shape design of a submerged entry nozzle.

• Design & Manufacturing
• /
• 제15권3호
• /
• pp.19-25
• /
• 2021

The bending process of a press die is to bend a flat blank to the required angle. There are V-bending, U-bending, Z-bending, O-bending etc. for bending processing, and the basic principle of calculating the unfolding length of die processing is used as the neutral plane length. Since the constant of the length value of the neutral surface is different depending on the type of bending, it is impossible to accurately calculate it. In particular, Z-bending processing is performed twice, and it is set on the upper and lower surfaces of the blank, and bending processing occurs at the same time as the upward and downward bending, and the elongation of the material occurs and the material increases. It is not possible to check with the calculated value, and it occurs in many cases where the mold is modified after start-up. This study aims to minimize die modification by developing a formula to calculate the development length of Z-bend.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.13-19
• /
• 2023

Blanking processing is one of the shear processing method in which the cut part becomes a product and piercing processing is a press molding process in which the cut part is discarded as a scrap. The shear angle of the punch used for blanking is determined by conditions such as the characteristics of the shear material, shear thickness and shear length. The shear angle of a punch is an important factor in determining the size of the shear load, the life of the shear punch, the deformation of the shear product and the quality of burrs In this study, blanking punches applied with four types of shear angles (i.e., 0°, 0°23", 0°46", 0°69") to the blanking punches of bracket products used in practical work were manufactured and tested. In the blanking experiment, the remaining variables except for the shear angle were the same. Experiments show that the product has the least amount of deformation in blanking punches with a shear angle equal to the material thickness, i.e., 0°46"..

• 한국정밀공학회지
• /
• 제12권11호
• /
• pp.148-158
• /
• 1995

This paper describes a hierarchical structure for feature definition and classification, and feature representation method based on frame structure for process planning of prismatic machined components of injection mold. The concept of Volume Removal Directions and Vertical Faces is proposed to develop a method to define and to classify features for components of injection mold systematically. A method for classifying features by the combination of volume removal directions and vertical faces is developed, and also a feature representation method by using frame structure to represent design and manufacturing information is presented.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.1-4
• /
• 2008

LCD-BLU (Liquid Crystal Display - Back Light Unit) is one of kernel parts of LCD unit and it consists of several optical sheets(such as prism, diffuser and protector sheets), LCP (Light Guide Plate), light source (CCFL or LED) and mold frame. The LGP of LCD-BLU is usually manufactured by forming numerous dots with $50-200{\mu}m$ in diameter on it by erosion method. But the surface of the erosion dots of LGP is very rough due to the characteristics of the erosion process during the mold fabrication, so that its light loss is high along with the dispersion of light into the surface. Accordingly, there is a limit in raising the luminance of LCD-BLU. Especially, the negative and positive micro-lens pattern fabricated by modified LiGA with thermal reflow process was applied to the optical design of LGP.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.159-165
• /
• 2004

The shrinkages of injection molded parts are different in molding operational conditions and mold design. It also differs from resins. The shrinkages of injection molded parts for PBT (polybutylene terephthalate), PC (polycarbonate),and glass reinforced PBT and PC have been studied for various operational conditions of injection molding. The part shrinkage of crystalline polymer, PBT was higher than that of amorphous polymer, PC by about two times. The part shrinkages of both polymers decreased as glass fiber content increases. Higher Injection temperature and lower injection pressure resulted in a higher shrinkage in both PBT and PC resins. As mold temperature increases the part shrinkage of PC decreased. However, the part shrinkage of PBT increased as mold temperature increases. The part shrinkage of both PBT and PC resins decreased as gate size increases since the pressure delivery is mush easier for a larger gate size. The part shrinkage of flow direction was less than that of the perpendicular direction to the flow for both pure and glass fiber reinforced resins. The part shrinkage at the position close to the gate was less than that of the position far from the gate.