• Bulletin of the Korean Chemical Society
• /
• 제35권12호
• /
• pp.3553-3558
• /
• 2014

The reduced graphene oxide(rGO)/aluminum phosphate($AlPO_4$)-coated $LiMn_{1.5}Ni_{0.5}O_4$ (LMNO) cathode material has been developed by hydroxide precursor method for LMNO and by a facile solution based process for the coating with GO/$AlPO_4$ on the surface of LMNO, followed by annealing process. The amount of $AlPO_4$ has been varied from 0.5 wt % to 1.0 wt %, while the amount of rGO is maintained at 1.0 wt %. The samples have been characterized by X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy. The rGO/$AlPO_4$-coated LMNO electrodes exhibit better cyclic performance compared to that of pristine LMNO electrode. Specifically, rGO(1%)/$AlPO_4$(0.5%)- and rGO(1%)/$AlPO_4$(1%)-coated electrodes deliver a discharge capacity of, respectively, $123mAhg^{-1}$ and $122mAhg^{-1}$ at C/6 rate, with a capacity retention of, respectively, 96% and 98% at 100 cycles. Furthermore, the surface-modified LMNO electrodes demonstrate higher-rate capability. The rGO(1%)/$AlPO_4$(0.5%)-coated LMNO electrode shows the highest rate performance demonstrating a capacity retention of 91% at 10 C rate. The enhanced electrochemical performance can be attributed to (1) the suppression of the direct contact of electrode surface with the electrolyte, resulting in side reactions with the electrolyte due to the high cut-off voltage, and (2) smaller surface resistance and charge transfer resistance, which is confirmed by total polarization resistance and electrochemical impedance spectroscopy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1030-1033
• /
• 2004

We herewith report for the effect of dielectric surface modification on the electrical characteristics of organic thin-film transistors (OTFTs). The kist-jm-1 as an organic molecule for the surface modification is deposited onto the surface of zirconium oxide ($ZrO_2$) gate dielectric layer. The OTFTs are elaborated on the flexible plastic substrates through 4-level mask process to yield a simple fabrication process. In this work, we also have examined the dependence of electrical performance on the interface surface state of gate dielectric/pentacene, which may be modified by chemical properties in the gate dielectric surface.

• Advances in environmental research
• /
• 제8권1호
• /
• pp.23-38
• /
• 2019

In this study, Malachite Green (MG) dye removal from synthetic wastewaters by adsorption process using raw boron enrichment waste (BEW) and it's modifications (with acid and ultrasound) were aimed. 81% MG removal was obtained by BEW at optimum equilibrium conditions (time: 40 min., dosage: 500 mg/dm³, pH: 5-6, speed: 200 rpm, 298 K). MG removal from wastewaters using acid modified boron enrichment waste (HBEW) was determined as 82% at optimum conditions (time: 20 min., dosage: 200 mg/dm³, pH: 10, speed: 200 rpm, 298 K). For ultrasound modified BEW (UBEW), the highest MG removal percent was achieved as 84% at optimum conditions (time: 30 min, dosage: 375 mg/ dm³, pH: 8, speed: 200 rpm, 298 K). The equilibrium data of Malachite Green was evaluated for BEW, HBEW and UBEW adsorbents by using sorption isotherms such as Langmuir, Freundlich and Temkin models, out of which Langmuir model (R² = 0.971, 0.987 and 0.984) gave better correlation and maximum adsorption capacity was found to be 147.05, 434.78 and 192.30 mg/g, respectively. The adsorption kinetics followed the pseudo-second-order kinetic equation for sorption of MG onto wastes. A look at thermodynamic data reveals that natural sorption is spontaneous and endothermic because of free negative energy exchange and positive change in enthalpy, respectively. The results indicated that boron enrichment waste, and HCl and ultrasound-modified boron enrichment waste served as good alternative adsorbents in dye removal from wastewater.

• 정보처리학회논문지:컴퓨터 및 통신 시스템
• /
• 제2권10호
• /
• pp.413-420
• /
• 2013

정전 방지 장치가 없는 중소형 레이드 (RAID: redundant arrays of independent disks)는 갑작스런 정전 또는 오류로 인한 종료 이후에 수시간의 긴 재동기화 시간을 요구한다. 레이드에서는 데이터 블록과 패리티 블록이 일관성 있게 갱신되어야 하는데, 데이터를 기록하다가 정전이 되면 데이터 블록은 갱신되었는데 패리티 블록은 갱신되지 않거나 반대인 경우가 발생할 수 있다. 이렇게 부분적으로 갱신된 스트라이프를 반드시 올바른 패리티로 갱신해야 하나 어떤 스트라이프에 이런 문제가 발생하였는지 찾기가 매우 어려웠다. 기존에는 전 저장공간을 검색하고 오류 있는 스트라이프를 수정하는, 수 시간을 요구하는, 패리티 재동기화 방법이 사용되어 왔다. 본 논문은 중소형 레이드에서 낮은 오버헤드를 갖는 고속의 재동기화 기술을 제안한다. 제안하는 기술은 리눅스의 소프트웨어 레이드에서 구현되었다. 성능 실험 결과에 따르면, 제안하는 기법은 재동기화 과정을 200분에서 5초로 단축시키고, 일반 입출력에서 22%의 오버헤드를 2%로 낮추었다.

• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.63-69
• /
• 2013

Negative-temperature coefficient (NTC) thermistors based on nickel manganite spinel ($NiMn_2O_4$) are widely used for many applications, such as sensors and temperature compensators, due to their good thermistor characteristics and stabilities. However, to achieve thermistors with a high NTC B constant, which is an important figure of merit pertaining to the degree of temperature sensitivity, the activation energy should be high such that high resistivity at ambient temperatures results. To obtain a high B constant and low resistivity, Al and Si modified spinel structured $Ni_{0.6}Si_{0.2}Al_{0.6}Mn_{1.6}O_4$ hybrid thick films with the conducting metal oxide of $LaNiO_3$ were fabricated on a glass substrate by aerosol deposition at room temperature (RT). The NTC-$LaNiO_3$ hybrid thick films showed resistivity as low as < $100k{\Omega}\;cm$ at $90^{\circ}C$, which is one or two orders of magnitude lower than that of the monolithic NTC films, while retaining a high B constant of $NiMn_2O_4$ of over 5500 K when 20 wt% $LaNiO_3$ was added without a post-thermal treatment. These phenomena are explained by the percolation threshold mechanism.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.148-148
• /
• 2017

Surface modification is a type of mechanical manipulation skills to achieve extensive aims including corrosion control, exterior appearance, abrasion resistance, electrical insulation and electrical conductivity of substrate materials by generating a protective surface using electrical, physical and chemical treatment on the surface of parts made from metallic materials. Such surface modification includes plating, anodizing, chemical conversion treatment, painting, lining, coating and surface hardening; this study conducted cavitation experiment to assess improvement of durability using anodizing. In order to observe surface characteristics with applied current density, the electrolyte temperature, concentration was maintained at constant condition. To prevent hindrance of stable growth of oxide layer due to local temperature increase during the experiment, stirring was maintained at constant speed. In addition, using galvanostatic method, it was maintained at processing time of 40minutes for 10 to $30mA/cm^2$. The cavitation experiment was carried out with an ultra sonic vibratory apparatus using piezo-electric effect with modified ASTM-G32. The peak-to-peak amplitude was $30{\mu}m$ and the distance between the horn tip and specimen was 1mm. The specimen after the experiment was cleaned in an ultrasonic bath, dried in a vacuum oven for more than 24 hours, and weighed with an electric balance. The surface damage morphology was observed with 3D analysis microscope. As a result of the study, differences were observed surface hardness and anti-cavitation characteristics depending on the development of oxide film with the anodizing process time.

• Toxicological Research
• /
• 제33권4호
• /
• pp.315-323
• /
• 2017

Preconceptual sex selection is still a highly debatable process whereby X- and Y-chromosome-bearing spermatozoa are isolated prior to fertilization of the oocyte. Although various separation techniques are available, none can guarantee 100% accuracy. The aim of this study was to separate X- and Y-chromosome-bearing spermatozoa using methods based on the viability difference between the X- and Y-chromosome-bearing spermatozoa. A total of 18 experimental semen samples were used, written consent was obtained from all donors and results were analysed in a blinded fashion. Spermatozoa were exposed to different pH values (5.5, 6.5, 7.5, 8.5, and 9.5), increased temperatures ($37^{\circ}C$, $41^{\circ}C$, and $45^{\circ}C$) and ROS level ($50{\mu}M$, $750{\mu}M$, and $1,000{\mu}M$). The live and dead cell separation was done through a modified swim-up technique. Changes in the sex-chromosome ratio of samples were established by double-label fluorescent in situ hybridization (FISH) before and after processing. The results indicated successful enrichment of X-chromosome-bearing spermatozoa upon incubation in acidic media, increased temperatures, and elevated $H_2O_2$. This study demonstrated the potential role for exploring the physiological differences between X-and Y-chromosome-bearing spermatozoa in the development of preconceptual gender selection.

• Journal of Electrochemical Science and Technology
• /
• 제14권4호
• /
• pp.388-396
• /
• 2023

Photoelectrochemical (PEC) water splitting is a vital source of clean and sustainable hydrogen energy. Moreover, the large-scale H₂ production is currently necessary, while long-term stability and high PEC activity still remain important issues. In this study, a GaN-based photoelectrode was modified by an additional NH₃ treatment (900℃ for 10 min) and its PEC behavior was monitored. The bare GaN exhibited a highly crystalline wurtzite structure with the (002) plane and the optical bandgap was approximately 3.2 eV. In comparison, the NH₃-treated GaN film exhibited slightly reduced crystallinity and a small improvement in light absorption, resulting from the lattice stress or cracks induced by the excessive N supply. The minor surface nanotexturing created more surface area, providing electroactive reacting sites. From the surface XPS analysis, the formation of an N-Ga-O phase on the surface region of the GaN film was confirmed, which suppressed the charge recombination process and the positive shift of E_FB. Therefore, these effects boosted the PEC activity of the NH₃-treated GaN film, with J values of approximately 0.35 and 0.78 mA·cm^-2 at 0.0 and 1.23 V_RHE, respectively, and an onset potential (V_on) of -0.24 V_RHE. In addition, there was an approximate 50% improvement in the J value within the highly applied potential region with a positive shift of V_on. This result could be explained by the increased nanotexturing on the surface structure, the newly formed defect/trap states correlated to the positive V_on shift, and the formation of a GaO_xN_1-x phase, which partially blocked the charge recombination reaction.

• 대한기계학회논문집
• /
• 제17권1호
• /
• pp.162-171
• /
• 1993

본 연구에서는 2성분혼합물의 응고과정해석에 머시영역의 비등방성을 포함시 킬수 있는 모델을 정립하고 실제계산을 수행하여 비등방성이 천이현상 및 조대편석(m- acrosegregation)에 미치는 영향을 보이고자 한다. 이 과정에서 기본 방정식의 변형 을 통한 수치해석의 효율화에 관해서도 취급할 것이다. 해석대상은 비등방성의 효과 가 잘 나타날 수 있으면서 해석은 용이한 2차원 정사각형용기로 선택하였다. 대상혼 합물은 실용적으로 관심있는 금속 합금과 결정구조가 유사하며 물성치가 비교적 잘 확 립된 염화암모늄수용액(NH$_{4}$C1-H$_{2}$O)이다. 특히 아공정염화암모늄수용액은 부력비(buoyancy factor)가 -1.4정도로서 온도와 농도구배에 의한 부력이 크기는 비슷 하지만 작용방향이 반대이기 때문에 이중확산대류의 전형적인 형태를 고찰하기에 편리 한 물질이다.

• 한국전산유체공학회지
• /
• 제10권2호
• /
• pp.38-47
• /
• 2005

Substructuring methods are often used in finite element structural analyses. In this study a multi-level substructuring(MLSS) algorithm is developed and proposed as a possible candidate for finite element fluid solvers. The present algorithm consists of four stages such as a gathering, a condensing, a solving and a scattering stage. At each level, a predetermined number of elements are gathered and condensed to form an element of higher level. At the highest level, each sub-domain consists of only one super-element. Thus, the inversion process of a stiffness matrix associated with internal degrees of freedom of each sub-domain has been replaced by a sequential static condensation of gathered element matrices. The global algebraic system arising from the assembly of each sub-domain matrices is solved using a well-known iterative solver such as the conjugare gradient(CG) or the conjugate gradient squared(CGS) method. A time comparison with CG has been performed on a 2-D Poisson problem. With one domain the computing time by MLSS is comparable with that by CG up to about 260,000 d.o.f. For 263,169 d.o.f using 8 x 8 sub-domains, the time by MLSS is reduced to a value less than $30\%$ of that by CG. The lid-driven cavity problem has been solved for Re = 3200 using the element interpolation degree(Deg.) up to cubic. in this case, preconditioning techniques usually accompanied by iterative solvers are not needed. Finite element formulation for the incompressible flow has been stabilized by a modified residual procedure proposed by Ilinca et al.[9].