• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1699-1701
• /
• 2005

Islanding phenomenon is undesirable because it lead to a safety hazard to utility service personnel and may cause damage to power generation and rower supply facilities as a result of unsynchronized reclosure. In order to prevent this phenomenon, various anti-islanding methods have been studied. Even though the slip mode frequency shift(SMS) method has been regarded as a highly effective anti-islanding method, the analytical design method of that was not cleared. This paper proposes a modeling of the SMS method using non-detection tone(NDZ) and evaluation of the method according to the test conditions of IEEE Std. 929-2000. The SMS method is derived analytically through modeling and verified visually by simulation and experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.10
• /
• pp.199-207
• /
• 2003

The Timoshenko beam model has been known as the most accurate model for representing beam structures. However, the Timoshenko beam model may give rise to a significant error when it is applied to multi-stepped beam structures. This paper is intended to demonstrate the modeling error of Timoshenko beam based finite element model for multi-stepped beam structures and to suggest a new modeling method to improve the accuracy. A tentative bending spring is introduced into the stepped section to represent the softening effect due to the presence of step. This paper also proposes a finite element modeling method in the light with the tentative bending spring model for the step softening effect. The proposed method rigorously adapts computation results from a commercial finite element code. The validity of the proposed method is demonstrated through a series of simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.647-649
• /
• 2001

It is a indispensible condition that the simulation and the experiment to improve a efficiency of maglev system. We usually carry out the simulation using the approximate equation, because it is impossible to use a exact modeling such as a practice modeling. This paper proposed a ideal simulation ap to the maglev system modeling by Finite Ele Method. To save the electrical energy, zero p control method is used, and verifying the feasibi FEM dynamic simulation, we make an exper with a TI DSP TMS320F240-based hardware.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.4
• /
• pp.14-21
• /
• 2012

This paper study a method of modeling and simulation of LED driver circuit for a design optimization. Simplified LED modeling is introduced and a driver IC, HV9910, is modeled by implementing the major function blocks. Circuit of buck type converter is constructed for simulation. Simulation includes not only the internal function of IC but also the various performance results such as LED array current control and dimming. Experiment results are also shown to prove the verification of its usage. This results show that the simulation approach is valid for a circuit optimization and a reduction of development time.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.57-59
• /
• 2003

Digital surface model generation from IKONOS stereo imagery is a new challenge in photogrammetric community, especially when the satellite company does not provide the raw data as well as their ancillary ephemeris data. In this paper we utilized an estimated relief displacement azimuth and the nominal collection elevation data included in the metadata file to correct the relief displacement of GCPs, together with a linear transformation for geometric modeling of IKONOS imagery. Space intersection is performed by the trigonometric intersection assuming a parallel projection of IKONOS imagery due to its small FOV and frame size. In the experiment, less than 2-meters of RMSE in orbit modeling is achieved denoting the potential positioning accuracy of the IKONOS stereo imagery.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.902-905
• /
• 2004

Characteristics of electrodelss lamp as a load of the ballast is different compared to normal fluorescent lamp because the lamp includes the magnetics for inductive discharging process. So somewhat different modeling is necessary to make a proper power match between the lamp and ballast. Modeling of an electrodeless lamps, Endura of Osram, is presented in this paper. Simulation with a result of experiment is given for a verification of proposed model.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.1006-1013
• /
• 1988

We have shown how unstructured modeling was used to derive a general stability condition in Part 1. In Part 2, we focus on the particular dynamics (structures modeling) of the robot manipulator and environment. Using rigid body dynamics, the stability condition for the direct drive robots has been achieved in terms of the Jacobian and robot tracking controller. Combining the structured and unstructured modeling, a stability condition for a particular application can be obtained. This approach has been used to analyze compliant motion on the University of Minnesota robot using a feedforward torque controller. We have obtained a stability condition for this application. Through both simulation and experiment, the sufficiency of this condition has been demonstrated. For a sufficient stability condition, recall that if the condition is satisfied, then the stability is guaranteed; however, if the condition is violated, no conclusion can be made.

• Journal of The Korean Association For Science Education
• /
• v.34 no.5
• /
• pp.479-490
• /
• 2014

The purpose of this study is to develop an argument-based modeling strategy, utilizing writing and argumentation for communication in science education. We need to support students and teachers who have difficulty in modeling in science education, this strategy focuses on development of four kinds of factors as follows: First, awareness of problems, recognizing in association with problems by observing several problematic situations. Second is science concept structuralization suggesting enough science concepts by organization for scientific explanation. The third is claim-evidence appropriateness that suggests appropriate representation as evidence for assertions. Last, the use of various representations and multimodal representations that converts and integrates these representations in evidence suggestion. For the development of these four factors, this study organized three stages. 'Recognition process' for understanding of multimodal representations, and 'Interpretation process' for understanding of activity according to multimodal representations, 'Application process' for understanding of modeling through argumentation. This application process has been done with eight stages of 'Asking questions or problems - Planning experiment - Investigation through observation on experiment - Analyzing and interpreting data - Constructing pre-model - Presenting model - Expressing model using multimodal representations - Evaluating model - Revising model'. After this application process, students could have opportunity to form scientific knowledge by making their own model as scientific explanation system for the phenomenon of the natural world they observed during a series of courses of modeling.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.131-134
• /
• 2004

Characteristics of electrodelss lamp as a load of the ballast is different compared to normal fluorescent lamp because the lamp includes the magnetics for inductive discharging process. So somewhat different modeling is necessary to make a proper power match between the lamp and ballast. Modeling of an electrodeless lamps, Endura of Osram, is presented in this paper. Simulation with a result of experiment is given for a verification of proposed model.

• Journal of Convergence for Information Technology
• /
• v.10 no.12
• /
• pp.236-244
• /
• 2020

In this research a suspended solid transport experiment was conducted in the river experiment center to find the characteristics and dispersion of the material. Modeling by the particle dispersion model was also executed to reproduce the suspended solid transport. The suspended solid was consisted of a mixture of silica and water using a mixing equipment, which was then introduced into a real-scale flume and measured with the laser-diffraction based particle size analyzer(LISST) to find the concentration of the material. The comparison between the measured suspended solid concentration using drone images and particle size analyzers, with the model showed a good match overall, which proved the applicability of the model. Along with finding the model applicability, the research showed the potential for suspended solid estimation in high flow situations with high rainfall.