• 전력전자학회논문지
• /
• 제20권4호
• /
• pp.344-350
• /
• 2015

A battery management system requires accurate information on the battery state of charge (SOC) to achieve efficient energy management of electric vehicle and renewable energy systems. Although correct SOC estimation is difficult because of the changes in the electrical characteristics of the battery attributed to ambient temperature, service life, and operating point, various methods for accurate SOC estimation have been reported. On the basis of piecewise linear (PWL) modeling technique, this paper proposes a simple SOC observer for lithium-polymer batteries. For performance evaluation, the SOC estimated by the PWL SOC observer, the SOC measured by the battery-discharging experiment and the SOC estimated by the extended Kalman filter (EKF) estimator were compared through a PSIM simulation study.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2000년도 창립총회 및 춘계학술발표회
• /
• pp.133-136
• /
• 2000

Soil decontamination process was conducted to study adsorption and modeling characteristic of Sr$^{2+}$ ion using citric acid and water system with TRIGA soil. When the concentration of citric acid was increased, the BTC of Sr$^{2+}$ ion was to be closed to the BTC of $^3$$H_2O$ at experiments of soil adsorption. Beside, when the concentration of citric acid was under 0.01M Sr$^{2+}$ ion, BTLs was asymmetry. It was characteristic of nonequilibrium adsorption. R and $K_{p}$ , were decreased to be increased the concentration of citric acid. Asymmetry modeling was nearly the same to be compare with symmetry modeling in decontamination process, when the concentration of citric acid was decreased. Result of experiment was agree with asymmetry and symmetry model, when the concentration of citric acid was increased.eased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.283-287
• /
• 1996

The exhaust noise reduction of automobile with the active muffler is experimentally investigated. The control algorithm is the filtered-x LMS algorithm and the inverse algorithm with the adaptive line enhancer. Also, the control efficiency is increased with synthesized second harmonic engine frequency. In the experiment, the active muffler is applied to the end of exhaust system in automobile and the control with on-line secondary path modeling method(inverse algorithm) is compared the control of off-line secondary path modeling method. As secondary path transfer functions are changed, the experimental results show that the control performance with on-line method is more efficient than that with off-line method in the exhaust noise reduction of automobile.

• Korean Journal of Geomatics
• /
• 제2권1호
• /
• pp.31-35
• /
• 2002

This paper describes an experiment for three-dimensional positioning for a pair of KOMPSAT stereostrips using the ancillary data and a single ground control point. The photogrammetric model for three-dimensional positioning was performed as follows: first, initialization of orbital and attitude parameters derived from ancillary data; second, adjustment of orbital and attitude parameters for the satellite to minimize the ground position error with respect to a GCP using the collinearity condition; third, determination of actual satellite position; and lastly, space intersection. This model was tested for a pair of stereo strips with 0.6 base-to-height ratio and GCPs identified from a 1:5,000 scale digital map. As the result, the satellite position of offset was corrected by only one GCP and the accuracy for the geometric modeling showed 38.89m RMSE.

• 소성∙가공
• /
• 제10권7호
• /
• pp.558-564
• /
• 2001

An experimental modeling is applied to investigate the formation of forms in molten aluminum By using a specially designed equipment, the effect of process variables, such as the shape of stirrer, stirring velocity and fluid viscosity, on the formation of foams were studied in the glycerine added water. Bubbles formed in water had various diameter from 1 to 10 mm and the number of bubbles was 0 to 20/$cm^2$. It turned out that among various variables the stirring velocity and fluid viscosity played important roles on the formation of bubbles. The results obtained from the model experiment were preyed to be convincible also in the real aluminum foam.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.520-522
• /
• 2005

Islanding phenomenon is undesirable because it lead to a safety hazard to utility service personnel and may cause damage to power generation and power supply facilities as a result of unsynchronized reclosure. In order to prevent this phenomenon, various anti-islanding methods have been studied. Even though the slip mode frequency shift (SMS) method has been regarded as a highly effective anti-islanding method, the analytical design method of that was not cleared. This paper proposes a modeling of the SMS method using non-detection zone (NDZ) and evaluation of the method according to the test conditions of IEEE Std. 929-2000. The SMS method is derived analytically through the modeling and verified visually by simulation and experiment.

• Journal of Mechanical Science and Technology
• /
• 제15권4호
• /
• pp.441-447
• /
• 2001

Ultrasonic wave generation and propagation were modeled to simulate an ultrasonic test. A ray model was used for the modeling. Actual sound pressure distribution of the incident wave from an angle probe was analyzed using an ultrasonic visualization method to incorporate the actual sound pressure distribution in the model. In this method, the sound pressure was expressed by the density of rays and the reflection coefficient of ultrasonic beams. Reflection and mode conversion of rays were computed by the Snells law. Simulation programs for the problem of ultrasonic testing of a butt joint are built using this ray modeling. Simulation results for ultrasonic wave scattering from a defect and A-scan display in ultrasonic testing agreed with the actual experiment results.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.64-72
• /
• 1998

This paper a new approach to the design of machine vision technique with a camera modeling that accounts for major sources of geometric distortion, namely, radial, decentering, and thin prism distortion. Radial distortion causes an inward or outward displacement of a given image point from its ideal location. Actual optical systems are subject to various degrees of decentering , that is , the optical centers of lens design and manufacturing as well as camera assembly. It is our propose to develop the vision system for the pattern recognition and the automatic test of parts and to apply the line of manufacturing. The performance of proposed vision system is illustrated by simulation and experiment.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.181-188
• /
• 2006

Operation parameters for large scale industrial facility such as iron making plant are carefully selected through elaborate tests and monitoring rather than through a mathematical modeling. One of the recent progresses for better energy utilization in iron ore sintering process is the distribution pattern of fuel inside a macro particle which is formed with fines of iron ore, coke and limestone. Results of model tests which have been used as a basis for the improved operation in the field are introduced and a theoretical modeling study is presented to supplement the experiment-based approach with fundamental arguments of physical modeling, which enables predictive computation beyond the limited region of tests and adjustment. A single fuel particle model along with one-dimensional bed combustion model of solid particles are utilized, and thermal processes of combustion and heat transfer are found to be dominant consideration in the discussions of productivity and energy utilization in the sintering process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1699-1701
• /
• 2005

Islanding phenomenon is undesirable because it lead to a safety hazard to utility service personnel and may cause damage to power generation and rower supply facilities as a result of unsynchronized reclosure. In order to prevent this phenomenon, various anti-islanding methods have been studied. Even though the slip mode frequency shift(SMS) method has been regarded as a highly effective anti-islanding method, the analytical design method of that was not cleared. This paper proposes a modeling of the SMS method using non-detection tone(NDZ) and evaluation of the method according to the test conditions of IEEE Std. 929-2000. The SMS method is derived analytically through modeling and verified visually by simulation and experiment.