• 한국공간구조학회논문집
• /
• 제16권4호
• /
• pp.29-36
• /
• 2016

The objective of this research is to development of a parametric design system for membrane structures. The parametric design platform for the spatial structures has been designed and implemented. Rhino3D is used as a 3D graphic kernel and Grasshopper is introduced as a parametric modeling engine. Modeling components such as structural members, loading conditions, and support conditions are developed for structural modeling of the spatial structures. The interface module with commercial structural analysis programs is implemented. An iterative generation algorithm for design alternatives is a part of the design platform. This paper also proposes a design approach for the parametric design of Spoke Wheel membrane structures. A parametric modeling component is designed and implemented. SOFiSTik is examined to interact with the design platform as the structural analysis module. The application of the developed interface is to design optimally Spoke Wheel Shaped Ductile Membrane Structure using parametric design. It is possible to obtain objective shape by controlling the parameter using a parametric modeling designed for shape finding of spoke wheel shaped ductile membrane structure. Recently, looking at the present Construction Trends, It has increased the demand of the large spatial structure. But, It requires a lot of time for Modeling design and the Structural analysis. Finally an optimization process for membrane structures is proposed.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1657-1664
• /
• 1995

For dynamic analysis of flexible structures, classical linear modeling has been widely used due to its several good aspects. However, it was found that the modeling often lost its accuracy. So, it is important to know the valid range of the modeling before it is used. more complicated modelings are needed to obtain reliable results only outside the valid range of the classical linear modeling. In this study, some rigid body motions of flexible structures which lead to the failure of the classical linear modeling are investigated. Hybrid deformation variable modeling, which is proved to be accurate in previous studies, is used to figure out the valid range of the classical linear modeling through numerical examples.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.127-134
• /
• 1998

The objectives of this paper is to analyze the reinforced concrete structures by using fiber model. In this study, the fiber modeling techniques including modeling of support conditions are studied. In order to verify the modeling techniques, analysis results obtained for reinforced concrete cantilever beam and reinforced concrete T-girder bridge under cyclic loading are compared with experimental results from full scale test. From the comparison, it is shown that the modeling techniques in this study can be well applied to the nonlinear failure analysis of reinforced concrete structures with porper modifications.

• 대한기계학회논문집A
• /
• 제21권6호
• /
• pp.933-941
• /
• 1997

In the analysis of thin elastic structures such as plate and shell-like structures, classical lower-order theories like Kirchhoff and Reissner-Mindin theories are insufficient to describe the behavior of such structures in the region where the state of stresses is complex. On the other hand, the fully three dimensional theory of linear elasticity can provide desired analysis accuracy, but requires expensive computational implementation compared to the classical theories. This paper is concerned with the development of hierarchical models for elastic structures which can be used for hierarchical modeling for the analysis of such structures. Derivation and limit model analysis (when the thickness of structures tends to zero) of hierarchical models are presented together with a introduction of modeling error estimation. Also, numerical results supporting theoretical results are given.

• 대한기계학회논문집
• /
• 제19권6호
• /
• pp.1363-1370
• /
• 1995

A nonlinear dynamic modeling method for simply supported structures undergoing large overall motion is suggested. The modeling method employs Rayleigh-Ritz mode technique and Von Karman nonlinear strain measures. Numerical study shows that the suggested modeling method provides qualitatively different results from those of the Classical Linear Cartesian modeling method. Especially, natural frequency variations and residual deformation due to membrane strain effects are observed in the numerical results obtained by the suggested modeling method.

• Advances in Computational Design
• /
• 제4권3호
• /
• pp.211-221
• /
• 2019

Numerical modeling of reinforced concrete structures is a difficult engineering problem, primarily because of the material inhomogeneity. The behaviour of a concrete element with reinforcement can be analyzed using, for example, the Barcelona model, which according to the literature, is one of the most suitable models for this purpose. This article compares the experimental data obtained for an orthotropic concrete slab band system with those predicted numerically using Concrete Damage Plasticity model. Abaqus package was used to perform the calculations.

• Smart Structures and Systems
• /
• 제8권3호
• /
• pp.275-302
• /
• 2011

This is a review paper on mathematical modeling of actively controlled piezo smart structures. Paper has four sections to discuss the techniques to: (i) write the equations of motion (ii) implement sensor-actuator design (iii) model real life environmental effects and, (iv) control structural vibrations. In section (i), methods of writing equations of motion using equilibrium relations, Hamilton's principle, finite element technique and modal testing are discussed. In section (ii), self-sensing actuators, extension-bending actuators, shear actuators and modal sensors/actuators are discussed. In section (iii), modeling of thermal, hygro and other non-linear effects is discussed. Finally in section (iv), various vibration control techniques and useful software are mentioned. This review has two objectives: (i) practicing engineers can pick the most suitable philosophy for their end application and, (ii) researchers can come to know how the field has evolved, how it can be extended to real life structures and what the potential gaps in the literature are.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.401-406
• /
• 1991

An integrated control design and modeling method of multibody space structures is presented as a tool to control an d describe the large rotational motions of the space structures. The structures representeed with three separated substructures have independent control systems but linked with joints interacting the dynamic motions of the substructures. The effect of the structural flexibility to the control performance was analyzed and the simulation results showed that effectiveness of the designed control logic in controlling the motions of the multi-body space structures.

• 한국정밀공학회지
• /
• 제14권2호
• /
• pp.136-144
• /
• 1997

Usually triangular patches are used to transfer geometric shape in Rapid Prototyping CAM system. STL, a list of triangles, is de facto standard in RP industry. Because STL does not have topological infoma- tion, it can cause errornous results. So STL should be verified before using. After adding support structures to anchor the part to the platform and to prevent sagging or distortion, slicing and layer by layer manufactur- ing process are done. But triangular patch is surface model and cannot provide sufficient information on geometry in the above processes. So, geometric modeling is necessary in verifying STL, adding support structures and slicing. It is natural that triangle based modeling is the best when tringular patches are used as input. Considering support structures, solid and faces coexist in RP process. Therefore non-manifold modeler is required. In this study, triangle based non-manifold geometric modeling is proposed for RP sys- tem consistent with STL input.

• 한국해양공학회지
• /
• 제14권3호
• /
• pp.20-28
• /
• 2000

Using the hydraulic and numerical model of semi-enclosed bay (Chinhae Bay), the efficiencies of flow-control structures on the seawater-circulation in the inner bay were investigated. Expecially, this study was confirmed the effectiveness of the flow-control structures at the mouth and narrow channel of Chinhae Bay through the experiments. The system of flow-control structures could enhance the water exchange improvement appropriately. The results of this study can be used as the long-term and integrated environmental impact assessment model in the inner bay.