• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.319-324
• /
• 2001

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or corner. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The experiment has been done to verify the effectiveness of the proposed controllers. These results are shown to fit well by the simulation results.

• Nuclear Engineering and Technology
• /
• v.54 no.6
• /
• pp.2048-2054
• /
• 2022

The coolant temperature feedback coefficient is an important parameter of reactor core power control system. To study the coolant temperature feedback coefficient influence on the core power control system of small PWR, the core power control system is built with the nonlinear model and fuzzy control theory. Then, the uncertainty quantification method of reactor core parameters is established based on the Latin hypercube sampling method and the Bootstrap method. Finally, under the conditions of reactivity step perturbation and coolant inlet temperature step perturbation, uncertainty analysis for two cases is carried out. The result shows that with fuzzy controller and fuzzy PID controller, the uncertainty of the coolant temperature feedback coefficient affects the core power control system, and the maximum uncertainties of core relative power, coolant temperature deviation, fuel temperature deviation and total reactivity are acceptable.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.94-104
• /
• 1996

This paper presents a new approach to the design of adaptive control system using DSPs(TMS320C31) for robotic manpulators to achieve accurate trajectory tracking by the joint angles Digital signal processors are used in implementing real time adaptive control algorithms to provide an enhanced motion control for robotic manipulators. In the proposed contorl scheme, adaptation laws are derived from the improved Lyapunov second stability analysis method based on the adaptive model reference control theory. The adaptive controller consists of an adaptive feedforward controller, feedback controller, and PID type time varying auxillary control elements. The proposed adaptive control scheme is simple in structure, fast in computation, and suitable for implementation of real-time control. Morever, this scheme does not require an accurate dynamic modeling nor values of manpipulator parameters and payload. Performance of the adaptive controller is illustated by simulation and experimental results for a SCARA robot.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.1
• /
• pp.151-159
• /
• 2008

The parameter-based cardiovascular impedance simulator that is able to overcome the limits of conventional mock circulatory systems is critical for the development and test of biomedical devices including artificial heart. The concept of impedance simulator was validated mathematically in a previous study using high-gain feedback linearization control which, however, may cause serious difficulties and limits for practical implementation. In this study, therefore, practical applicability of the impedance simulator is investigated considering the physical limits such as motor speed and torque. Simple PID controller which do not require complex model of the simulator is used considering the practical implementation. Design guidelines of the impedance simulator are also provided based on the results.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1551-1561
• /
• 2014

Design, Simulation and experimental analysis of closed loop time domain based Discrete PWM buck-boost converter are described. To improve the transient response and dynamic stability of the proposed converter, Discrete PID controller is the most preferable one. Discrete controller does not require any precise analytical model of the system to be controlled. The control system of the converter is designed using digital PWM technique. The proposed controller improves the dynamic performance of the buck-boost converter by achieving a robust output voltage against load disturbances, input voltage variations and changes in circuit components. The converter is designed through simulation using MATLAB/Simulink and performance parameters are also measured. The discrete controller is implemented, and design goal is achieved and the same is verified against theoretical calculation using LabVIEW.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1796-1799
• /
• 1997

This thersis presents precise position control emthods of a 3-PRPS in-parallel manipulator for industrial applications such as assembly of highly integrated semiconductors and microsurgery. Since real-time ontrol is one of the most important issues required for industrial application, the experimental hardware is set up with a VME based DSP controller. In the 3-PRPS parallel mainpulator, structurally existing frictiion at three horizontal links considerably degrades the precise position control. In order to compensate the friction of the horizontal links in the joint space, a disturbance compensation usign disturbance and velocity observers has been proposed and investigated. We analyzed the decision method of eigenvalues of the disturbance observer and the effects of the control resulted form tehsystem model errors. Through a series of simulations and experiments, we see that the methods is capable of compensating variations of the robot parameters such as inertia and damping as well as the joint friction. Experiments show that the disturbance compensation method usign disturbance and velocity observer is very effective to compensate the friction. Compared with conventional PID position control, it decreased position errors ina circular motion by approximately 70%.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.6
• /
• pp.297-304
• /
• 2014

Due to the nonlinearity and complexity of the three-phase photovoltaic inverter, we propose an intelligent control based on fuzzy logic and the classical proportional-integral-derivative. The feedback linearization method is applied to cancel the nonlinearities, and transform the dynamic system into a simple and linear subsystem. The system is transformed from abc frame to dq0 synchronous frame, to simplify the state feedback linearization law, and make the close-loop dynamics in the equivalent linear model. The controls improve the dynamic response, efficiency and stability of the three-phase photovoltaic grid system, under variable temperature, solar intensity, and load. The intelligent control of the nonlinear characteristic of the photovoltaic automatically varies the coefficients $K_p$, $K_i$, and $K_d$ under variable temperature and irradiation, and eliminates the oscillation. The simulation results show the advantages of the proposed intelligent control in terms of the correctness, stability, and maintenance of its response, which from many aspects is better than that of the PID controller.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.405-413
• /
• 2006

In general mechanical servo systems, friction deteriorates the performance of controllers by its nonlinear characteristics. Especially, friction phenomenon causes steady-state tracking errors and limit cycles in position and velocity control systems, even though gains of controllers are tuned well in linear system model. Even if sensor is used higher accuracy level, it is difficult to improve tracking performance of the position to the same level with a general control method such as PID type. Therefore, many friction models were proposed and compensation methods have been researched actively. In this paper, we consider that the variation of mover's mass is various by loading and unloading. The normal force variation occurs by it an other parameters. Therefore, the proposed control system is composed of main position controller and a friction compensator. A parameter estimator for a nonlinear friction model is designed by adaptive control law and adaptive backstepping control method.

• Journal of Navigation and Port Research
• /
• v.31 no.1 s.117
• /
• pp.55-64
• /
• 2007

In general mechanical servo systems, friction deteriorates the performance of controllers by its nonlinear characteristics. Especially, friction phenomenon causes steady-state tracking errors and limit cycles in position and velocity control systems, even though gains of controllers are tuned well in linear system model. Even if sensor is used higher accuracy level, it is difficult to improve tracking performance of the position to the same level with a general control method such as PID type. Therefore, many friction models were proposed and compensation methods have been researched actively. In this paper, we consider that the variation of mover's mass is various by loading and unloading. The normal force variation occurs by it and other parameters. Therefore, the proposed control system is composed of main position controller and a friction compensator. A parameter estimator for a nonlinear friction model is designed by adaptive control law and adaptive backstepping control method.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.18 no.1
• /
• pp.81-93
• /
• 2005

Purpose : There are various oriental medicine therapy of treating Pelvic Inflammatory Disease(PID) in clinics. We made the PID mice model by injection Lipopolysaccharide (LPS) in vagina, and investigate anti-inflammatory effects of Hongdeung-Tang among oral medication, retention enema therapy and herbal-acupuncture treatment. Method : The ICR(20-30g) mice(♀) were used. To examine the occurrence of inflammation, LPS in different concentration was injected into the vagina of the mice, and White Blood Cell(WBC) in blood was counted. To examine anti-inflammatory effects, 6 mice were assigned to each of the normal group, the control group and the sample group. Hongdeung-Tang was medicated in oral and rectal with 1.0g/kg low dose and 3.0g/kg high dose and by herbal acupucture for 5 days, 2 days before LPS injection. After 3days from LPS injection, blood was collected from retro-orbital plexus, and WBC, Interleukin-6(IL-6), Tumor Necrosis Factor-${\alpha}$(TNF-${\alpha}$) in the blood was counted. Result : After LPS injection with each dose, WBC count showed significant increase depending on LPS concentration from $100{\mu}g/kg$, and it was maximized at 3 or 4 days after LPS injection. the Hongdeung-Tang treatment groups, The number of WBC was decreased significantly only in low dose and high dose oral medication, and IL-6 concentration showed significant decrease in oral and rectal medication as well as in herbal acupuncture treatment. TNF-${\alpha}$ concentration was decreased significantly in oral and rectal medication of low dose and high dose. herbal-acupuncture treatment group datas showed reductive tendency. Conclusion : Based on above results, we made the PID mice model by injection LPS in vagina, and demonstrated anti-inflammatory effect of Hongdeung-Tang of oral medication, retention enema therapy and herbal-acupuncture treatment.