• Structural Engineering and Mechanics
• /
• v.75 no.1
• /
• pp.123-131
• /
• 2020

The bond performance of glass fibre reinforced polymer (GFRP) bars and that of steel bars embedded in Alkali Activated Cement (AAC) concrete are analysed and compared using pull-out specimens. The bond failure modes, the average bond strength and the free end bond stress-slip curves are used for comparison. Tepfers' concrete ring model is used to further analyse the splitting failure in ribbed steel bar and GFRP bar specimens. The angle the bond forces make with the bar axis was calculated and used for comparing bond behaviour of ribbed steel bar and GFRP bars in AAC concrete. The results showed that bond failure mode plays a significant role in the comparison of the average bond stress of the specimens at failure. In case of pull-out failure mode, specimens with ribbed steel bars showed a higher bond strength while specimens with GFRP bars showed a higher bond stress in case of splitting failure mode. Comparison of the bond stress-slip curves of ribbed steel bars and GFRP bars depicted that the constant bond stress region at the peak is much smaller in case of GFRP bars than ribbed steel bars indicating a basic bond mechanism difference in GFRP and ribbed steel bars.

• Journal of Korea Water Resources Association
• /
• v.46 no.1
• /
• pp.25-34
• /
• 2013

In this study, the development processes of multiple bars in the channels with erodible banks were investigated by double Fourier analysis. The initially straight channels in the experiment flume were widened with eroding the side banks, and the multiple bars were generated and grew due to stalling of the sediment on the bed. The bars migrated downstream and the size of the bars increased with time. The flow was separated around the bars, and the bed and banks near the bars were scoured due to the impinged secondary flow. The morphologic changes were accelerated by the bank erosion, which affected the fluctuations of sediment discharge downstream. The double Fourier analysis of the bed waves showed that 1-1 mode (alternate bar) was dominant at the initial stage of the channel development. As time increased, 2-3 mode (central or multiple bars) was dominant due to the increased width to depth ratio. Moreover, the number of bars in a cross section of the channel were increased due to the non linearity of alternate bars. The width to depth ratio was increased by the bank erosion, which affected the bar migration and the bar wavelength. However, the dimensionless tractive force was decreased by it.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.529-533
• /
• 2012

본 연구에서는 실내실험을 통하여, 하안침식을 고려한 망상하천에서 저수로의 이동특성을 조사하며, 2중 퓨리에 해석에 의하여 사주의 거동특성을 분석하였다. 실내실험은 평균입경이 1.4 mm이고, 표준편차가 1.35인 균일사로 10 cm 의 두께로 전체가 균등하게 채워진, 길이가 12 m, 넓이 2 m 수로에서 수행하였다. 각 시간별 하도의 지형변화에 대하여 2 중 Fourier 해석에 의한 지배적인 성분, 즉 모드(mode)의 변화를 분석하였다. 여기서 1-1 mode는 교호사주(alternate bars)이고, 1-2 mode와 2-2 mode는 2차 횡방향 모드로서 중앙 사주(central bars)를 나타낸다. 1-3 mode와 2-3 mode는 한 단면에서 횡방향으로 3개의 사주가 형성된 것(triple row bars)를 나타낸다. 초기에는 1-1 mode인 교호사주가 지배적이지만, 시간이 증가함에 따라, 교호사주인 1-1 mode는 감소하고, 한 단면에서 3개의 사주가 형성되는 2-3 mode가 지배적인 것으로 나타났다. 이러한 원인은 시간이 지나면서 사주가 발달하고, 하안침식이 되면서, 하폭이 증가하여 상대적으로 수심이 감소하면서 복렬사주가 발달하기 때문이며, Colombini 등(1987)이 이론적으로 예측한 결과와 잘 일치한다. 한 단면에서 3개의 모드가 나타나는 것은 하상에서 변화를 일으키는데 중요한 역할을 한다. 직선하도에서 사주의 수가 증가하는 것은 교호사주의 강한 비선형으로 상호작용하기 때문이다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.27-34
• /
• 2012

The objective of this study is to evaluate the stiffness of mortar-filled sleeve bar splice using estimation method of failure mode in the sleeve reinforcement splice. To attain this goal, we analyzed the test results of 261 actual-sized mortar-filled sleeve splice specimens. The study results showed that the estimation method of the failure mode in mortar-filled sleeve bar splice made an effective estimate of the stiffness in this bar splice with the exception of specimens with SD500 bars and smooth pipe sleeve. Especially, of the specimens with cast sleeve or uneven pipe sleeve in the range of reinforcement fracture using the estimation method of the failure mode in mortar-filled sleeve splice, specimens over 98% with SD400 bars and all specimens with SD500 bars had the stiffness capacity of higher than "A" class of AIJ code in monotonic loading. In addition, of the specimens in the range of reinforcement fracture using the estimation method of the failure mode in mortar-filled sleeve splice, all specimens with SD400 bars and SD500 bars had the stiffness capacity of higher than "A" class of AIJ code in cyclic loading.

• Earthquakes and Structures
• /
• v.18 no.1
• /
• pp.113-127
• /
• 2020

In this study, the behavior of external beam-column joints reinforced by plain and deformed bars with non-seismic reinforcement details is investigated and compared. The beam-column joints represented in this study include a benchmark specimen by seismic details in accordance with ACI 318M-11 requirements and four other deficient specimens. The main defects of the non-seismic beam-column joints included use of plain bar, absence of transverse steel hoops, and the anchorage condition of longitudinal reinforcements. The experimental results indicate that using of plain bars in non-seismic beam-column joints has significantly affected the failure modes. The main failure mode of the non-seismic beam-column joints reinforced by deformed bars was the accumulation of shear cracks in the joint region, while the failure mode of the non-seismic beam-column joints reinforced by plain bars was deep cracks at the joint face and intersection of beam and column and there was only miner diagonal shear cracking at the joint region. In the other way, use of plain bars for reinforcing concrete can cause the behavior of the substructure to be controlled by slip of the beam longitudinal bars. The experimental results show that the ductility of non-seismic beam-column joints reinforced by plain bars has not decreased compared to the beam-column joints reinforced by deformed bars due to lack of mechanical interlock between plain bars and concrete. Also it can be seen a little increase in ductility of substructure due to existence of hooks at the end of the development length of the bars.

• Structural Engineering and Mechanics
• /
• v.63 no.5
• /
• pp.629-637
• /
• 2017

Continuous concrete beams are commonly used as structural members in the reinforced concrete constructions. The use of fiber reinforced polymer (FRP) bars provide attractive solutions for these structures particularly for gaining corrosion resistance. This paper presents experimental results of eight two-span continuous concrete beams; two of them reinforced with pure glass fiber reinforced polymer (GFRP) bars and six of them reinforced with combinations of GFRP and steel bars. The continuous beams were tested under monotonically applied loading condition. The experimental load-deflection behavior and failure mode of the continuous beams were examined. In addition, the continuous beams were analyzed with a numerical method to predict the load-deflection curves and to compare them with the experimental results. Results show that there is a good agreement between the experimental and the theoretical load-deflection curves of continuous beams reinforced with pure GFRP bars and combinations of GFRP and steel bars.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.935-940
• /
• 2002

This paper presents the failure mode on Headed Bars and prediction of tensile capacity, which is governed by concrete cone failure. 17 different plate types, three different concrete strengths and three different welding types of specimens were simulated. Static tensile load was applied Headed Bars were manufactured in different areas, and their shape and thickness are based on ASTM 970-98. Calculation of embedment length in concrete is conducted based on CSA 23.3-94, and static tensile load was applied. Tested pullout capacities were compared to the values determined using current design methods such as ACI-349 and CCD method.

• Computers and Concrete
• /
• v.22 no.6
• /
• pp.573-592
• /
• 2018

An analytical methodology for the calculation of the flexural and the shear capacity of concrete members with Fibre-Reinforced-Polymer (FRP) bars as tensional reinforcement is proposed. The flexural analysis is initially based on the design provisions of ACI 440.1R-15 which have properly been modified to develop general charts that simplify computations and provide hand calculations. The specially developed charts include non-dimensional variables and can easily be applied in sections with various geometrical properties, concrete grade and FRP properties. The proposed shear model combines three theoretical considerations to facilitate calculations. A unified flexural/shear approach is developed in flow chart which can be used to estimate the ultimate strength and the expected failure mode of a concrete beam reinforced with longitudinal FRP bars, with or without transverse reinforcement. The proposed methodology is verified using existing experimental data of 138 beams from the literature, and it predicts the load-bearing capacity and the failure mode with satisfactory accuracy.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.1
• /
• pp.41-51
• /
• 2004

FRP re-bar in concrete structures could be used as a substitute of steel re-bars for that cases in which aggressive environment produce high steel corrosion, or lightweight is an important design factor, or transportation cost increase significantly with the weight of the materials. But FRP fibers have only linearly elastic stress-strain behavior; whereas, steel re-bar has linear elastic behavior up to the yield point followed by large plastic deformation and strain hardening. Thus, the current FRP re-bars are not suitable concrete reinforcement where a large amount of plastic deformation prior to collapse is required. The main objectives of this study in to evaluate the tensile behavior and the fracture mode of hybrid FRP re-bar. Fracture mode of hybrid FRP re-bar is unique. The only feature common to the failure of the hybrid FRP re-bars and the composite is the random fiber fracture and multilevel fracture of sleeve fibers, and the resin laceration behavior in both the sleeve and the core areas. Also, the result of the tensile and interlaminar shear stress test results of hybrid FRP re-bar can provide its excellent tensile strength-strain and interlaminar stress-strain behavior.

• Structural Engineering and Mechanics
• /
• v.11 no.4
• /
• pp.357-372
• /
• 2001

In this paper, cantilevered tall structures are treated as cantilever bars with varying cross-section for the analysis of their free longitudinal (or axial) vibrations. Using appropriate transformations, exact analytical solutions to determine the longitudinal natural frequencies and mode shapes for a one step non-uniform bar are derived by selecting suitable expressions, such as exponential functions, for the distributions of mass and axial stiffness. The frequency equation of a multi-step bar is established using the approach that combines the transfer matrix procedure or the recurrence formula and the closed-form solutions of one step bars, leading to a single frequency equation for any number of steps. The Ritz method is also applied to determine the natural frequencies and mode shapes in the vertical direction for cantilevered tall structures with variably distributed stiffness and mass. The formulae proposed in this paper are simple and convenient for engineering applications. Numerical example shows that the fundamental longitudinal natural frequency and mode shape of a 27-storey building determined by the proposed methods are in good agreement with the corresponding measured data. It is also shown that the selected expressions are suitable for describing the distributions of axial stiffness and mass of typical tall buildings.