• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.2
• /
• pp.124-131
• /
• 2002

This paper presents the design of an active vibration suppression controller for an air-spring type vibration isolation table. Firstly, isolation system model is constructed considering the isolation table, attached equipment and voice-coil actuator. An active control system is designed based on frequency-shaped sliding mode control theory rewarding high frequency uncertainties with respect to attached equipments on the isolation table. Finally. the performance of the active isolation system is evaluated by simulation under some disturbance conditions which are transmitted from base structure of the isolation system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.726-730
• /
• 2001

Temperature stabilities of dielectric constraints and resonant frequencies of the substrates are very important in piezoelectric ceramics oscillators and filters. In this study, it was investigated temperature stability of the length-extensional vibration mode of Pb(Zr$\_$y/Ti$\_$1-y/)O$_3$+x[wt%]Cr$_2$O$_3$ ceramics. The mode can be utilized in fabricating ultra-small 455 kHz IF devices. Addition of Cr$_2$O$_3$ in morphotrophic phase PZT decreased the variations of dielectric constant, electro-mechanical coupling factor k$\_$31/ and resonant frequency by thermal shock. As additive weight of Cr$_2$O$_3$increased, the temperature coefficient of resonant frequency changed from positive number to negative one. And the composition tith temperature coefficient of resonant frequency was shifted to the one with increased Cr$_2$O$_3$ additive weigh by thermal aging.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1246-1257
• /
• 2004

The objective of this paper is to characterize dynamic pressure traces measured at self-excited combustion instabilities occurring in two combustion systems of different hardware. One system is a model lean premixed gas turbine combustor and the other a fullscale bipropellant liquid rocket thrust chamber. It is commonly observed in both systems that low frequency waves at around 300㎐ are first excited at the onset of combustion instabilities and after a short duration, the instability mode becomes coupled to the resonant acoustic modes of the combustion chamber, the first longitudinal mode for the lean premixed combustor and the first tangential mode for the rocket thrust chamber. Low frequency waves seem to get excited at first since flame shows the higher heat release response on the lower frequency perturbations with the smaller phase differences between heat release and pressure fluctuations. Nonlinear time series analysis of pressure traces reveals that even stable combustion might have chaotic behavior with the positive maximum Lyapunov exponent. Also, pressure fluctuations under combustion instabilities reach a limit cycle or quasi-periodic oscillations at the very similar run conditions, which manifest that a self-excited high frequency instability has strong nonlinear characteristics.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.8-14
• /
• 2004

Nondestructive evaluation (NDE) technique method using a resonance frequency mode was carried out for woodceramics produced at different carbonizing temperatures (600℃, 800℃, 1000℃, 1200℃, 1500℃) at the phenol resin impregnation rate of 70%, for three kinds of species (Pinus densifora, Pinus koraiensis, Larix leptolepis), respectively. There was a poor relationship between density and static bending MOR. However, close correlations were found between dynamic MOE_d and static bending MOR, and between static MOEs and MOR. Especially, the correlation coefficient was highest between MOE_d and static bending MOR. Therefore, the MOE_d using the resonance frequency mode is useful as a NDE method for predicting the MOR of woodceramics produced at different carbonizing temperatures.

• Computers and Concrete
• /
• v.31 no.1
• /
• pp.1-7
• /
• 2023

In this paper, Timoshenko-beam model is developed for the vibration of double carbon nanotubes. The resulting frequencies are gained for axial wave mode and length-to-diameter ratios. The natural frequency becomes more prominent for lower length-to-diameter ratios and diminished for higher ratios. The converse behavior is observed for axial wave mode with clamped-clamped and clamped-free boundary conditions. The frequencies of clamped-free are lower than that of clamped-clamped boundary condition. The eigen solution is obtained to extract the frequencies of double walled carbon nanotubes using Galerkin's method through axial deformation function. Computer softer MATLAB is used for formation of frequency values. The frequency data is compared with available literature and found to be in agreement.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3497-3500
• /
• 2007

The internal structure is subjected to dynamic analysis due to the structural integrity. The internal structure shall be installed in the vertical hole call IR1 of reactor core. In order to verify the deflection of the internal structure, the mode and response spectrum analysis of the internal structure was performed. The natural frequency of the internal structure is 11.6 Hz(mode 1 and 2) and deflections of the internal structure are less than values of allowable design (3.2 mm).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1169-1176
• /
• 2002

Analytical model of beat response is derived on a slightly asymmetric ring and is veryfied by experiment. The asymmetric ring is a simplified model used to explain the beat property of a Korean bell. The asymmetric ring has mode pair having slight frequency difference in each radial mode. Each mode pair produces beat phenomenon by the interaction of the two close frequency components. Based on the analytical model, beat maps are first proposed and characteristics of beat on the circumference are detaily explained.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.349-354
• /
• 2000

The modal analysis based on deformations is the method to drived dynamic responsed from superposition of natural frequency and mode shape. In order to free vibration analysis of the structures, Aluminum-made model is used in experiment. The dynamic characteristic of the structures are determined from acceleration measurements using impulse hammer. Experimenrt input and output signal are derive from impact hammer and the one accerometer. This paper present three methods for calculating the natural frequencies and mode shapes of the structure with theory value and finite element analysis, experiment. The results were good approximated about natural frequency and mode shape.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.473-480
• /
• 2020

In this paper, we proposed a high frequency equivalent circuit considering parasitic impedance components for differential noise analysis on the input stage during DC-DC buck converter switching operation. Based on the proposed equivalent circuit model, we presented a method to measure parasitic impedance parameters included in DC bus plate, IGBT, and PCB track using the gain phase method of a network analyzer. In order to verify the validity of this model, a DC-DC prototype consisting of a buck converter, a signal analyzer, and a LISN device, and then resonance frequency was measured in the frequency range between 150 kHz and 30 MHz. The validity of the parasitic impedance measurement method and the proposed equivalent model is verified by deriving that the measured resonance frequency and the resonance frequency of the proposed high frequency equivalent model are the same.

• Journal of the Optical Society of Korea
• /
• v.17 no.2
• /
• pp.177-181
• /
• 2013

We present an all-fiberized power-scalable, sub-nanosecond mode-locked laser based on a frequency-shifted-feedback ring cavity comprised of an erbium-doped fiber, a downshifting acousto-optic modulator (AOM), and a bandpass filter (BPF). With the aid of the frequency-shifted feedback mechanism provided by the AOM and the narrow filter bandwidth of 0.45 nm, we generate self-starting, mode-locked optical pulses with a spectral bandwidth of ~0.098 nm and a pulsewidth of 432 to 536 ps. In particular, the output power is readily scalable with pump power while keeping the temporal shape and spectral bandwidth. This is obtained via the consolidation of bound pulse modes circulating at the fundamental repetition rate of the cavity. In fact, the consolidated pulses form a single-entity envelope of asymmetric Gaussian shape where no discrete internal pulses are perceived. This result highlights that the inclusion of the narrow BPF into the cavity is crucial to achieving the consolidated pulses.