• Korean Journal of Medicinal Crop Science
• /
• v.22 no.5
• /
• pp.363-368
• /
• 2014

This study was conducted to find out the optimum composition of nursery soil for raising seedling of ginseng (Panax ginseng C. A. Meyer). Total 9 kinds of raw materials were used such as peat-moss, perlite, leaf mould, rice bran, gull's guano, castor-oil plant bark, palm bark, cow manure and chicken manure for optimum composition of nursery soil in ginseng. Occurrence of damping-off in ginseng was lowered about 50% in nursery soil type 1, 2 and 4 than in other types nursery soil in June, and occurrence rate of rusty root also lowest in nursery soil type 1. As the salinity of nursery soil increased, so did the occurrence of physiological disorder in ginseng seedling. The cause of salinity increasing in nursery soil has closely relation to $NO_3-N$, $P_2O_5$ and $Na^+$ content. Plant height, root length, diameter and weight were longer and heavier in nursery soil type 1 (mixing ratio of peat-moss, perlite and leaf mould was 50 : 20 : 30 based in volume) than in other types of nursery soil. So nursery soil type 1 was selected for raising seedling of ginseng. pH and electric conductivity (EC) of selected nursery soil type 1 was 5.55 and 0.13 dS/m. Contents of $NO_3-N$ and $P_2O_5$ were 21.0 and 40.0 mg/L, and $K^+$ 0.36, $Ca^{2+}$ 3.38, $Mg^{2+}$ 2.01 and $Na^+$ $0.09cmol^+/L$, respectively.

• Korean Journal of Remote Sensing
• /
• v.31 no.5
• /
• pp.409-419
• /
• 2015

The Atmospheric Emitted Radiance Interferometer (AERI) which is the Fourier Transform InfraRed (FTIR) spectrometer has been operated by the National Institute of Meteorological Research (NIMR) in Anmyeon island, South Korea since June 2010. The ground-based AERI with similar hyper-spectral infrared sensor to satellite could be an alternative way to validate satellite-based remote sensing. In this regard, the NIMR has focused on the improvement of Cloud data Filtering Method (CFM) which employed only one reference spectrum of clear sky in winter season. This study suggests Seasonal-Cloud data Filtering Method (S-CFM) which applied seasonal AERI reference spectra. For the comparison of applied S-CFM and CFM, the methane retrievals (surface volume mixing ratio) from AERI spectra are used. The quality of AERI methane retrieval applied S-CFM was significantly more improved than that of CFM. The positive result of S-CFM is similar pattern with the seasonal variation of methane from ground-based in-situ measurement, even if the summer season's methane is retrieved over-estimation. In addition, the comparison of vertical total column of methane from AERI and GOSAT shows good result except for the summer season.

• Applied Chemistry for Engineering
• /
• v.24 no.6
• /
• pp.587-592
• /
• 2013

In this study, we prepared pelletized porous carbon adsorbent (PCA) according to the different pyrolysis temperature using activated carbon and polyvinyl alcohol (PVA) as a binder for the removal of toluene, which is one of the representative volatile organic compounds (VOCs). We investigated physical characteristics of PCA using FE-SEM, BET, TGA and evaluated their adsorption capacity for toluene using GC. It was confirmed that the formability of pellets composed of the activated carbon, PVA and solvent of mass mixing ratio was 1 : 0.2 : 0.8 was the most outstanding. Toluene adsorption capacity was evaluated by measuring the maximum time when more than 99% of toluene adsorbed on the pellet. The specific surface area of the adsorbent pyrolyzed at $300^{\circ}C$ was measured as 4.7 times in $941.9m^2/g$ compared to that of the unpyrolyzed pellet. Micropore volume and toluene adsorption capacity of PCA increased fivefold to be 0.30 cc/g and thirteenfold to be 26 hours compared to that of the unpyrolyzed pellet, respectively. These results were attributed to the change of pore size and specific surface area due to the PVA content and the different pyrolysis temperature.

• Korean Journal of Food Science and Technology
• /
• v.15 no.3
• /
• pp.262-268
• /
• 1983

Properties of noodle prepared with FPC and wheat flour were investigated, and the results were summarized as follows: 1. Farinogram showed that the water absorption ratio and dough development time increased as the mixing level of FPC to wheat flour increased. 2. Amylogram showed that the maximum viscosity of the composite flour decreased as the content of FPC increased. 3. In the textural parameters, such as hardness, cohesiveness and gumminess of noodles, there were no marked differences between wheat flour and cooked noodles from the composite flour of 3% or 5% FPC-97% or 95% wheat flour. 4. Regarding weight and volume of the cooked noodles, those of cooked noodles from the composite flour of 3% or 5% FPC-97% or 95% wheat flour were similar to wheat flour alone. As the content of FPC in noodle increased, however, those of cooked noodles slightly decreased, and soup turbidity increased. 5. Results of sensory evaluations showed that the noodle from the composite flour of 3% FPC-97 wheat flour appeared to be the most acceptable, and the noodles from the composite flour of 5% or 7% FPC-95% or 93% wheat flour were judged as acceptable as the wheat flour alone.

• Fire Science and Engineering
• /
• v.24 no.4
• /
• pp.12-17
• /
• 2010

The purpose of this study is to determine how effectively waste tire recycled material mixed with flame retardant work in combating fire. As discovered in the previous study, waste tire mixed with cement mortar has more insulation capacity. However, this mortar is weak against fire. Therefore flame retardant, with a specific proportional mix, will be added to increase its fire prevention capacity. Tests will be made in accordance with ISO 5657 procedures for measuring fire ignition time, flame and shape variation of test pieces at the Building Material Test Institute. The test piece will be set up with horizontal levels having a constant radiation heat of $1{\sim}5W/cm^2$. Temperature transfers and increases from the surface into the interior. Combustible gases result due to pyrolysis, and regular contact is maintained between the fire source and the center of the test piece for assessment purposes. Ignition has not been occurred without adding retardant meaning that there is almost no possibility of ignition of waste tire particle. This fact can be considered as fire load to appreciate a volume of combustion materials. Flame is not occurred due to heat-absorbing effect by adding non-organic series retardant into waste tire particle. Conclusions have been summarized as follows; 1) Combustion of building material can be decreased by adding retardant to waste tire-mixing mortar. But compressive strength and insulation capacity of the material should be measured later. 2) Firing prevention and ignition are main points of building fire. Reasonable fire engineering assessment of interior material should be made for establishing effective disaster prevention system.

• Journal of Conservation Science
• /
• v.34 no.2
• /
• pp.107-118
• /
• 2018

This report does studied for making the method of conserving bracket murals in Daeungjeon of Jikjisa Temple, through the scientific way. Results of evaluated the conservation status at the braket mural paintings, most serious damage is structural damage like cracks, breakage, and delamination. After optical investigation, a characteristic point wasn't found such as underdrawing or traces of a coat of paint. The ultrasonic examination speed by each wall painting was measured from about 195.8 m/s to 392.7 m/s, according to the location of the surface, and it was able to compare the surface properties according to the location. In Infrared-thermal image measurement shows that wall layer separation and paint layer delamination are closely detected, therefore it was able to judge of damage on the objective way. Material analysis revealed that the walls were made by sand and weathering soil. The wall layer combined sand with less than fine sand size by nearly 5:5, and the finishing layer was found to have mixed medium sand and fine sand at approximately 6:4 rates. However, In case of finishing layer, mixing ratios of sizes less than very fine sand were found to be significantly lower than wall. Therefore, it is estimated that the plysical damage such as the separation between the layers of the walls created in the braket mural paintings, is continuously caused by changes in the internal stresses and volume ratio caused by the density differences between the wall and the finishing layers.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.4
• /
• pp.27-36
• /
• 2012

The water in surface of the earth is frozen under freezing point. The freezing phenomenon, which causes the volume change of soils, affects on the behavior of soils and causes the significant damage on the geotechnical structures. The purpose of this study is to investigate the characteristics of elastic waves in sand-silt mixtures using small size freezing cells, which reflect the frozen ground condition due to temperature change. Experiments are carried out in a nylon cell designed to freeze soils from top to bottom. Bender elements and piezo disk elements are used as the shear and compressional wave transducers. Three pairs of bender elements and piezo disk elements are placed on three locations along the depth. The specimen, which is prepared by mixing sand and silt, is frozen in the refrigerator. The temperature of soils changes from $20^{\circ}C$ to $-10^{\circ}C$. The velocities, resonant frequencies and amplitudes of the shear and compressional waves are continuously measured. Experimental results show that the shear and compressional wave velocities and resonant frequencies increase dramatically near the freezing points. The amplitudes of shear and compressional waves show the different tendency. The dominant factors that affect on the shear wave velocity change from the effective stress to the ice bonding due to freezing. This study provides basic information about the characteristics of elastic waves due to the soil freezing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.477-477
• /
• 2008

For more than three decades, the gate dielectrics in CMOS devices are $SiO_2$ because of its blocking properties of current in insulated gate FET channels. As the dimensions of feature size have been scaled down (width and the thickness is reduced down to 50 urn and 2 urn or less), gate leakage current is increased and reliability of $SiO_2$ is reduced. Many metal oxides such as $TiO_2$, $Ta_2O_4$, $SrTiO_3$, $Al_2O_3$, $HfO_2$ and $ZrO_2$ have been challenged for memory devices. These materials posses relatively high dielectric constant, but $HfO_2$ and $Al_2O_3$ did not provide sufficient advantages over $SiO_2$ or $Si_3N_4$ because of reaction with Si substrate. Recently, $HfO_2$ have been attracted attention because Hf forms the most stable oxide with the highest heat of formation. In addition, Hf can reduce the native oxide layer by creating $HfO_2$. However, new gate oxide candidates must satisfy a standard CMOS process. In order to fabricate high density memories with small feature size, the plasma etch process should be developed by well understanding and optimizing plasma behaviors. Therefore, it is necessary that the etch behavior of $HfO_2$ and plasma parameters are systematically investigated as functions of process parameters including gas mixing ratio, rf power, pressure and temperature to determine the mechanism of plasma induced damage. However, there is few studies on the the etch mechanism and the surface reactions in $BCl_3$ based plasma to etch $HfO_2$ thin films. In this work, the samples of $HfO_2$ were prepared on Si wafer with using atomic layer deposition. In our previous work, the maximum etch rate of $BCl_3$/Ar were obtained 20% $BCl_3$/ 80% Ar. Over 20% $BCl_3$ addition, the etch rate of $HfO_2$ decreased. The etching rate of $HfO_2$ and selectivity of $HfO_2$ to Si were investigated with using in inductively coupled plasma etching system (ICP) and $BCl_3/Cl_2$/Ar plasma. The change of volume densities of radical and atoms were monitored with using optical emission spectroscopy analysis (OES). The variations of components of etched surfaces for $HfO_2$ was investigated with using x-ray photo electron spectroscopy (XPS). In order to investigate the accumulation of etch by products during etch process, the exposed surface of $HfO_2$ in $BCl_3/Cl_2$/Ar plasma was compared with surface of as-doped $HfO_2$ and all the surfaces of samples were examined with field emission scanning electron microscopy and atomic force microscope (AFM).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.169-169
• /
• 2008

To keep pace with scaling trends of CMOS technologies, high-k metal oxides are to be introduced. Due to their high permittivity, high-k materials can achieve the required capacitance with stacks of higher physical thickness to reduce the leakage current through the scaled gate oxide, which make it become much more promising materials to instead of $SiO_2$. As further studying on high-k, an understanding of the relation between the etch characteristics of high-k dielectric materials and plasma properties is required for the low damaged removal process to match standard processing procedure. There are some reports on the dry etching of different high-k materials in ICP and ECR plasma with various plasma parameters, such as different gas combinations ($Cl_2$, $Cl_2/BCl_3$, $Cl_2$/Ar, $SF_6$/Ar, and $CH_4/H_2$/Ar etc). Understanding of the complex behavior of particles at surfaces requires detailed knowledge of both macroscopic and microscopic processes that take place; also certain processes depend critically on temperature and gas pressure. The choice of $BCl_3$ as the chemically active gas results from the fact that it is widely used for the etching o the materials covered by the native oxides due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. In this study, the surface reactions and the etch rate of $Al_2O_3$ films in $BCl_3/Cl_2$/Ar plasma were investigated in an inductively coupled plasma(ICP) reactor in terms of the gas mixing ratio, RF power, DC bias and chamber pressure. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by AFM and SEM. The chemical states of film was investigated using X-ray photoelectron spectroscopy (XPS), which confirmed the existence of nonvolatile etch byproducts.

• KSBB Journal
• /
• v.19 no.6 s.89
• /
• pp.446-450
• /
• 2004

We investigated the effective culture conditions of anaerobic bacteria, Enterobacter cloacae YJ-1 on hydrogen production. It was cultured with 60 mL of working volume at $35^{\circ}C$, 120 rpm for 40 h. With culture time, hydrogen production and cell growth increased, but residual glucose and pH decreased. When the $2\%$ of glucose was used as single carbon source, hydrogen production was 975.1 mL/L. To enhance hydrogen productivity, mixed carbon sources of glucose and sucrose were added. The maximum hydrogen production was earned at the mixing ratio of 25:75, and it was 1319.5 mL/L. When we added 50 mM of phosphate to protect the pH drop in culture broth, hydrogen production increased 1.3 times more than that of initial concentration. The organic nitrogen sources were more effective than inorganic nitrogen for hydrogen production. Among organic nitrogen, yeast extract was the most effective and its hydrogen production was 1691.3 mL/L. Among 9 of mineral sources, Ferric citrate and $NaMoO_4$ were especially effective, and their productions were 1782.3 mL/L and 1784.8 mL/L, respectively.