• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.437-444
• /
• 2005

본 연구는 연료-공기 혼합정도가 불안정 화염 구조와 NOx 배출 특성에 미치는 영향을 조사하기 위해 대기압, 모형 가스 터빈 연소기에서 실험을 수행하였다. 선회각은 $45^{\circ}$이며, 연료-공기 혼합정도는 당량비 0.53에서 0.79 범위에서 0, 50, 100%로 변화시켰다. 화염구조를 파악하기 위해, 당량비 0.79에서 ICCD를 사용하여 위상 동기화된 OH 자발광 이미지를 취득하였다. NOx 배출은 각 상기 실험조건에서 NOx 분석기를 이용하여 취득하였다. 위상에 대한 $OH^*$ 이미지를 취득함으로써 연료-공기 혼합정도가 화염의 구조에 미치는 영향을 확인할 수 있었다. 또한 국소 열방출의 특성을 통해, 연료-공기 혼합정도에 따른 연소불안정이 발생하거나 소멸되는 영역에 대한 정보를 얻을 수 있었으며, 혼합정도에 따른 NOx 농도를 측정함으로써 희박 연소 영역에서는 $\sigma$가 커질수록 NOx 발생이 적음을 확인할 수 있었다. 이런 결과들은 연소불안정 현상의 메카니즘을 이해하는데 중요한 기초자료로 사용될 것으로 기대된다.

• 조명전기설비학회논문지
• /
• 제29권6호
• /
• pp.49-57
• /
• 2015

This paper presents the discharge characteristics and economic feasibility of a Dry $Air/O_2$ and a $N_2/O_2$ mixture gas in order to review $SF_6$ alternative. From AC discharge experiment in an quasi-uniform field, it was found that the optimal $N_2/O_2$ mixing ratio which breakdown voltage and surface flashover voltage were the highest was 70/30 and that the pressure dependence on the breakdown voltage was higher than that of the surface flashover voltage in the Dry $Air/O_2$ and the $N_2/O_2$ mixture gas. The mixing ratio (70/30) and the tendency of the pressure dependence were described in detail based on physical factors (impact ionization coefficient, electron attachment coefficient, secondary electron emission coefficient) involved in discharge mechanism and a electron source, respectively. In addition, the performance insulation and the economic feasibility of the Dry $Air/O_2$ and the $N_2/O_2$ mixture gas were discussed so that Dry $Air/O_2$ mixture gaswas more suitable than $N_2/O_2$ mixture gas to the $SF_6$ alternative.

• 대한기계학회논문집B
• /
• 제21권8호
• /
• pp.1009-1023
• /
• 1997

The breakup length of a liquid jet with flowrate, formed by releasing through a nozzle of circular cross-section into the atmosphere, was experimented and studied for 3 liquid nozzles of varying diameters. The experimental result was analyzed using the existing theoretical equation for predicting the breakup length. It was found that the breakup length of liquid jet depends on the velocity, and the breakup length increases with increasing of the liquid nozzle diameter. Also, the variation range of the breakup length for the same flowrate of liquid increased rapidly as velocity was increased for laminar flow, but in the turbulent flow region, it leveled off in the range of approximately 0.55-0.7 of the mean breakup length. Furthermore, when the longest smooth liquid jet was applied to the co-axial flow air blast atomizer, the effect of air flow on the flow pattern and breakup length was studied for 6 glass nozzles of different lengths and diameters. It was found that depending on the diameter of the mixing tube and liquid jet, it was possible to observe a wide range of flow patterns, such as liquid jet through flow, partial annular flow and annular flow. The liquid jet breakup length was more sensitive to the change in the length rather than the diameter of the mixing tube. As the length of the mixing tube shortens, the breakup length also shortens rapidly.

• Transactions on Electrical and Electronic Materials
• /
• 제1권3호
• /
• pp.14-17
• /
• 2000

Giga bit dynamic random access memory(DRAM) requires the capacitor of high dielectric films. Some metal oxides films have been proposed as the dielectric material . And Pt is one of the most promising electrode materials. However very little has been done in developing the etching technologoy Pt film. Therefore, it is the first priority to develop the technology for plasma etching of Pt film. In this study, the dry etching of Pt film was investigated in Inductively Coupled Plasma(ICP) etching system with Cl$_2$/Ar and HBr/Cl$_2$/Ar gas mixing. X-ray photoelectron spectroscopy (XPS) was used in analysis of sidewall residues for the understanding of etching mechanism. We found the etch residues on the pattern sidewall is mainly Pt-Pt, Pt-Cl and Pt-Br compounds, Etch profile was observed by Scanning Electron Spectroscopy(SEM) . The etch rate of Pt film at 10%, Cl$_2$/90% Ar gas mixing ration was higher than at 100%. Ar. Addition of HBr to Cl$_2$/Ar as an etching gas led to generally higher selectivity to SiO$_2$. And the etch residues were reduced at 5% HBr/5% Cl$_2$/90% Ar gas mixing ration. These pages provide you with an examples of the layout and style which we wish you to adopt during the preparation of your paper, Make the width of abstract to be 14cm.

• 한국도로학회논문집
• /
• 제15권6호
• /
• pp.1-9
• /
• 2013

PURPOSES : About 35% of air pollutant is occurred from road transport. NOx is the primary pollutant. Recently, the importance of NOx removal has arisen in the world. $TiO_2$ is very efficient for removing NOx by photocatalytic reaction. The mechanism of removing NOx is the reaction of photocatalysis and solar energy. Therefore, $TiO_2$ in concrete need to be contacted with solar radiation to be activated. In general, $TiO_2$ concrete are produced by substitute $TiO_2$ as a part of concrete binder. However, 90% of $TiO_2$ in the photocatalysis can not contacted with the pollutant in the air and solar radiation. Coating and penetration method are attempted as the alternative of mixing method in order to locate $TiO_2$ to the surface of structure. METHODS : The goal of this study was to attempt to locate $TiO_2$ to the surface of concrete, so we can use the concrete in pavement construction. The distribution of $TiO_2$ along the depth were confirmed by basing on the comparison of $TiO_2$ compare by using the EDAX(Energy Dispersive X-ray Spectroscopy). RESULTS : $TiO_2$ were distributed within 3mm from concrete surface. This distribution of $TiO_2$ is desirable, since the $TiO_2$ induce photocatalysis are located to where they can be contacted with the air pollutant and solar radiation. CONCLUSIONS : Nano size $TiO_2$ is easily penetration in the top 3mm of concrete surface. By the penetration $TiO_2$ concrete can be produced with the use of only 10% of $TiO_2$, by comparing the mixing types.

• 한국결정성장학회지
• /
• 제32권4호
• /
• pp.143-150
• /
• 2022

알루미늄제련 폐기물을 IGCC 슬래그와 혼합하여 지오폴리머를 제조하고 물성을 기존 IGCC 슬래그 기반 지오폴리머와 비교하였다. 두 원료를 혼합했을 때 Si/Al 비율 1.78에서 가장 좋은 압축강도 값을 보였으며, Si/Al의 변화에 따라서 압축강도 및 밀도의 변화가 민감하지 않아 즉, 혼합 허용범위가 상당히 넓어 상용화시 유리하다고 판단되었다. 알루미늄제련 폐기물을 첨가한 지오폴리머는 기존 IGCC 슬래그 기반 지오폴리머 대비 압축강도가 높은 것을 확인할 수 있었으며, TCLP법에 의해 안전성 확인을 한 결과 인체에 무해하다는 것을 확인할 수 있었다. 따라서 알루미늄제련 폐기물을 일정 비율로 IGCC 슬래그와 혼합하여 지오폴리머를 제조한다면 지오폴리머의 물성 향상에도 도움이 될 뿐만 아니라 안전한 건축자재로 재활용될 수 있다고 결론지을 수 있었다.

• 한국건축시공학회지
• /
• 제9권6호
• /
• pp.113-119
• /
• 2009

본 연구는 양생요인 및 PP 섬유 혼입율 변화에 따른 고강도 콘크리트의 기초적 특성 및 내화특성을 분석하였는데, 그 결과를 요약하면 다음과 같다. 콘크리트의 기초적 특성으로 유동성은 PP 섬유 혼입율이 증가 할수록 감소하는 경향을 나타내었고, 압축강도는 PP 섬유 혼입율 증가에 따라 약간 감소하였으나 재령 7일에서 모두 60 MPa 이상 재령 28일에서 90 MPa이상으로 고강도 범위를 나타내었다. 함수율 변화에 따른 폭렬성상으로 함수율 3.0 %에서 PP 섬유를 혼입하지 않은 플레인을 제외한 모든 배합에서 폭렬이 방지되는 것으로 나타났다. 이때 폭렬이 방지된 경우 잔존압축강도율은 22~41%, 질량감소율 5~7 %로 비교적 양호한 것으로 분석되었다. 양생방법 변화에 따른 폭렬성상으로 표준양생의 경우 PP 섬유 혼입율 0.05 % 이상, 증기 양생 및 오토클레이브의 경우 PP 섬유 혼입율 0.10 %에서 폭렬이 방지되는 것으로 나타났다. 이때 폭렬이 방지된 경우 잔존압축강도율은 23~42 %, 질량감소율은 7~11 % 전후로 나타났다. 이상을 종합하여 볼때 고강도 콘크리트는 함수율이 작을수록 폭렬방지가 용이하고, 양생방법에 따라서는 표준양생이 PP섬유 0.05 % 이상, 증기양생 및 오토클레이브의 경우 PP 섬유 혼입율 0.1 %이상을 혼입해 주어야 폭렬이 방지됨을 알수 있었다.

• Ocean and Polar Research
• /
• 제35권3호
• /
• pp.249-258
• /
• 2013

Vertical and horizontal mixing processes in the ocean mixed layer determine sea surface temperature and temperature variability. Accordingly, simulating these processes properly is crucial in order to obtain more accurate climate simulations and more reliable future projections using an ocean general circulation model (OGCM). In this study, by using Modular Ocean Model version 4 (MOM4) developed by Geophysical Fluid Dynamics Laboratory, the upper ocean temperature and mixed layer depth were simulated with two different vertical mixing schemes that are most widely used and then compared. The resultant differences were analyzed to understand the underlying mechanism, especially in the Tropical Pacific Ocean where the differences appeared to be the greatest. One of the schemes was the so-called KPP scheme that uses K-Profile parameterization with nonlocal vertical mixing and the other was the N scheme that was rather recently developed based on a second-order turbulence closure. In the equatorial Pacific, the N scheme simulates the mixed layer at a deeper level than the KPP scheme. One of the reasons is that the total vertical diffusivity coefficient simulated with the N scheme is ten times larger, at maximum, in the surface layer compared to the KPP scheme. Another reason is that the zonal current simulated with the N scheme peaks at a deeper ocean level than the KPP scheme, which indicates that the vertical shear was simulated on a larger scale by the N scheme and it enhanced the mixed layer depth. It is notable that while the N scheme simulates a deeper mixed layer in the equatorial Pacific compared to the KPP scheme, the sea surface temperature (SST) simulated with the N scheme was cooler in the central Pacific and warmer in the eastern Pacific. We postulated that the reason for this is that in the central Pacific atmospheric forcing plays an important role in determining SST and so does a strong upwelling in the eastern Pacific. In conclusion, what determines SST is crucial in interpreting the relationship between SST and mixed layer depth.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.48-54
• /
• 2004

The effects of injector spacing s and injector diameter d on mixing are numerically investigated in supersonic combustor with perpendicular injection behind a backward-facing step. Simulations are reported for airstream Mach number of 2.4. Parameters are changed on following 4 cases to investigate the effects of injector configuration on mixing efficiency $\eta_m$. In the case of varying d or s, dynamic pressure ratio $Rq(=(pu^2)_j/(pu^2)_a)$ is also varied to keep bulk equivalence ratio $\Phi({\oe})Rq.d^2/s)$ constant. (l) Injector spacing s is varied at constant $\Phi$=0.5, 1, 2 for injector diameter d=6mm. In the case of $\Phi$=1, $\eta_m$ has its maximum value at s=24mm. The reason is that increase of $\eta_m$. , by widening spacing at Rq=constant competes with decrease of $\eta_m$ by increasing Rq at s=constant. When spacing is narrow, the flow field of vicinity of injector becomes two-dimensional because adjacent jets interferes each other. By widening spacing, air is easily entrained by three-dimensional effect. This mechanism also appears in the case of $\Phi$=0.5, 2 for d=6mm, and $\eta_m$. reaches its maximum value at s=24mm for $\Phi$=0.5 and at s=42mm for $\Phi$=2. (2) In the case of injector diameter d varied at $\Phi$=1 for s=30mm, $\eta_m$. has its maximum value at d=3mm. The reason is that decrease of $\eta_m$ by increasing injector diameter competes with increase of $\eta_m$ by decreasing Rq at d=constant.(3) In the case of s varied at $\Phi$=0.5, 1,2 for d=3mm, the injector spacing at which mixing efficiency has its maximum value is s= 18mm for $\Phi$=0.5, s=24mm for $\Phi$=1, s=24mm for $\Phi$=2. Therefore it is found that d=3mm and s=24mm can be optimum configuration over a range of $\Phi$=0.5~2.(4) The effect of h on the optimum spacing is investigated. s is varied for d=6mm at step height h=4, 6, 8mm. The simulation results do not show significant change on the step height.

• 콘크리트학회지
• /
• 제6권6호
• /
• pp.151-158
• /
• 1994

본 연구에서는 수경성 시멘트 경화체의 구조적 결함인 휨강도를 향상시키시 위해 보통 포틀랜드 시멘트비를 0.1로 하여 혼합수량을 줄이고 수용성 고분자 물질인 Hydroxy Propy Methyl Cellulose(HPMC)를 첨가하여 시멘트입자의 윤활작용에 따른 균일한 분산효과와 결합효과를 얻도록 하였으며, twin roll mill로 혼련 성형하여 치밀하고 균일한 경화제 시편을 제조하였다. 이러한 고강도 시멘트 경화체의 휨강도는 약 96MPa, 탄성계수는 60GPa로 우수한 특성을 나타내었다. 고강도 시멘트의 고강도화 기구는 100${\mu}m$ 이상의 큰 기공제거 및 균열성장경로인 모세관 기공의 감소, 미수화 시멘트의 증가로 인한 탄성계수의 증가와 crack toughening(입자 가교, 고분자 섬유 가교, frictional interlocking)에 의한 파괴 인성의 향상 때문인 것으로 판단된다.