• Ocean and Polar Research
• /
• v.26 no.2
• /
• pp.341-349
• /
• 2004

Hyrdography and deep currents were measured from 1997 to 1999 to investigate deep-sea environments in the KODOS (Korea Deep Ocean Study) area of the northeastern tropical Pacific. KODOS area is located meridionally from the North Equatorial Current to the boundary between the North Equatorial Current and the Equatorial Counter Current. Strong thermocline exists between 10 m and 120 m depths at the study area. Since that strong thermocline does hardly allow vertical mixing between surface and lower layer waters, vertical distributions of temperature, salinity, dissolved oxygen and nutrients drastically change near the thermocline. Salinity-minimum layer, which indicate the North Pacific Intermediate Water (NPIW) and the Antartic Intermediate Water (AAIW), vertically occupies vertically at the depths from 500 m down to 1400 m. The NPIW and the AAIW horizontally occur to the north and to the south of $7^{\circ}N$, respectively. The near-bottom water shows the physical characteristics of $1.05^{\circ}C$ and 34.70 psu at the depths of 10 m to 110 m above the bottom (approximately 4000-5000 m), which was originated from the Antarctic Circumpolar Water. It flows northeastwards for 2 to 4 months at the study area, and its mean velocity was 3.1-3.7 cm/s. Meanwhile, reverse (southwestward) currents appear for about 15 days with the average of 1.0-6.1 cm/s every 1 to 6 months. Dominant direction of the bottom currents obtained from the data for more than 6 months is northeastward with the average speeds of 1.7-2.1 cm/s. Therefore, it seems that deep waters from the Antarctica flow northwards passing through the KODOS area in the northeastern tropical Pacific.

• Journal of Korean Society on Water Environment
• /
• v.32 no.3
• /
• pp.243-252
• /
• 2016

In cases of water pollution accidents, accurate prediction for arrival time and concentration of contaminants in a river is essential to take proper measures and minimize their impact on downstream water intake facilities. It is critical to fully understand the behavior characteristics of contaminants on river surface, especially in case of oil spill accidents. Therefore, in this study, the effects of main parameters of advection and diffusion of contaminants were analyzed and validated by comparing the results of Lagrangian particle tracking (LPT) simulation of Environmental Fluid Dynamic Code (EFDC) model with those of Global Position System (GPS)-equipped drifter experiment. Prevention scenario modeling was accomplished by taking cases of movable weir operation into account. The simulated water level and flow velocity fluctuations agreed well with observations. There was no significant difference in the speed of surface particle movement between 5 and 10 layer modeling. Therefore, 5 layer modeling could be chosen to reduce computational time. It was found that full three dimensional modeling simulated wind effects on surface particle movements more sensitively than depth-averaged two dimensional modeling. The diffusion range of particles was linearly proportional to horizontal diffusivity by sensitivity analysis. Horizontal diffusivity estimated from the results of GPS-equipped drifter experiment was 0.096 m²/sec, which was considered to be valid for applying the LPT module in this area. Finally, the scenario analysis results showed that particle movements could be stagnant when discharge from the upstream weir was reduced, implying the possibility of securing time for mitigation actions such as oil boom installation and wiping oil contaminants. The outcomes of this study can help improve the prediction accuracy of particle tracking simulation to establish the most suitable mitigation plan considering the combination of movable weir operation.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.421-431
• /
• 2007

The main purpose of this study is to develop a sprayed FRP repair and strengthening method, which is a new technique for strengthening the existing concrete structures by mixing one of the carbon or glass chopped fibers and one of the epoxy or vinyl ester resins with high-speed compressed air in open air and randomly spraying the mixture onto the concrete surface. At present, the sprayed FRP repair and strengthening method using the epoxy resin has not been fully discussed. In order to investigate the material property of the sprayed FRP, this study carried out tensile tests of the material specimens, which were changed with the combinations of various variables including the length of chopped fiber and the mixture ratio of chopped fiber and resin. These variables were set to have the equal material strength, compared with that of one layer of the FRP sheet. As a result, the optimal length of glass and carbon chopped fibers was fumed out to be 38 mm, and the optimal mixture ratio between chopped fiber and resin was also turned out to be 1 : 2 from each variable. And also, the thickness of the sprayed FRP to have the equal strength to one layer of the FRP sheet was finally calculated. In is study, a series of experiments were carried out to evaluate the strengthening effects of flexural beams, shear beams and damaged beams strengthened with the sprayed FRP method, respectively. The results revealed that the strengthening effects of the flexural and shear specimens were reasonably similar to those of the FRP sheet, and the developed Sprayed FRP technique is able to be used as a strengthening scheme of existing RC building.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.3 no.1
• /
• pp.45-52
• /
• 1998

The transport of suspended matter was interpreted in the coastal zone off Taean Peninsula during the summer (June) in 1996. Coastal waters were homogenous in water temperature and salinity, whereas offshore waters were characterzed by the strong thermocline. Mixing between coastal and offshore waters are negligeable, largely lessened, due to the existence of strong tidal front between the two water masses. In the offshore area, less saline coastal waters from the Kyunggi Bay are considered to be transported southward along the mid-depth layer of thermocline. Concentration of suspended matters was higher than 5 mg/l in the northern coastal area near the Kyunggi Bay, but generally less than 2 mg/l in the offshore area. Less saline waters along the mid-depth layer in the offshore area sustain maximum turbidities throughout the water column. Therefore suspended matters supplied from the coastal area of Kyunggi Bay are considered to be transported southward by the advective movement of less saline coastal waters. Mean particle size of the suspended matters shows 2~9 ${\mu}m$. Coarse grains (mean size larger than 7 ${\mu}m$) are predominant in the less saline coastal waters extending to the offshore mid-depth waters. Such size distributions of suspended matters together with the characteristics of water masses are considered to be an indicator for the southward movement of suspended matters derived from Kyunggi Bay.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.13-22
• /
• 2007

This study was carried out to scrutinize possibility of manufacturing pitch pine (Pinus rigida) glued laminated timber in order to add values of pitch pine trees. Also, it was investigated to improve bending performance of pitch pine glulam. Pitch pine was imported as one of major plantation species in Korean peninsula. Machine stress rated grades of pitch pine lumber mostly ranged between E7 and E9. which grades were more or less inferior to producing high quality glulam. However, the adhesive properties between pitch pine and pitch pine, and between pitch pine and Japanese larch (Larix kaempferi Carr.), such as shear bond strength, wood failure rate and de-lamination rate of bonded layer submerged in cold and boiling water, were higher than Korean Standard criteria. These properties are essential for manufacturing glulam with single species or multiple species. The modulus of rupture (MOR) of pitch pine glulam exceeded the criterion of Korean Standard for glulam strength grade but modulus of elasticity (MOE) was lower than the criterion. On the other hand, the bending performances (MOR and MOE) were improved 20 percent by mixing with Japanese larch laminar. It is effective to arrange higher quality Japanese larch laminar at the outer layer of glulam for improving bending performances. In conclusion, it is possible to use low quality pitch pine as laminar of structural glulam for adding values of pitch pine.

• Applied Chemistry for Engineering
• /
• v.5 no.2
• /
• pp.199-208
• /
• 1994

In this study, the ultrasound which provides the properties of mixing, and surface cleaning effect, the increase of the effective reaction surface area and the enhancement of the effective collision frequency, was used to enhance the recovering efficiency of Cu from the Cu-ion containning waste water. The ultrasonic reactor used in this study was designed and constructed for improving the disadvantage of the existing ultrasonic reactor. From the experimental result and its analysis, we obtained following conclusions. 1. The ultrasound increased the rate of electrochemical deposition to 582.2% in maximum at the condition of $0.1M-CuSO_4$, and 2.1 V-overpotential. 2. The enhancement effect of ultrasound induced by the reduction of diffusion layer thickness was 277.8% in maximum and induced by the other effect except for the reduction effect of the diffusion layer thickness was 253.6% in maximum at $0.1M-CuSO_4$ and 2.1V overpotential. 3. This study gave the possibility of the scale-up of ultrasonic reactor and in particular, ultrasonic reactor would be effective in the treatment of waste water containning a low concentration of Cu ion.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.581-587
• /
• 2005

In order to obtain a highly purified p-dioxanone (PDX) as monomer of biodegradable polymer, suitable solvent must be selected. The selection was based on the solubility of impurities, and partial layer melt crystallization were carried out under the presence of solvent. The solubility of PDX in various solvents such as ethyl acetate, tetrahydrofuran, acetone, alcohols (methanol, ethanol, 1-propanol, 1-butanol and 1-pentanol) were measured over the temperature range of $-10{\sim}15^{\circ}C$. As solubility parameters, the mixing and dissolution enthalpy between the PDX and the solvents was studied based on empirical equations and the regular solution theory. The solubility and the temperature dependency of the solubility with the solvents of acetone, ethylacetate, and tetrahydrofuran of PDX were shown to have relatively high values compared to the alcohol type solvents. Also, in same alcohols, the smaller molecules and higher polarity gave higher solvency. In partial layer melt crystallization, small amount of ethylacetate selectively dissolved impurities and gave highly purified p-dioxanone, over 99.9% purity.

• Korean Journal of Microbiology
• /
• v.30 no.5
• /
• pp.383-390
• /
• 1992

In the periods of July 31 to August 10. 1988 and March 9 to 13. 1989. sediment samples were collected from the South Sea stations (010] to 092]) located in the area from $N 32^{\circ}$/30' to $34^{\circ}$/30', of latitude and from E $123^{\circ}$ 30' to $128^{\circ}$30' of longitude. These samples were analyzed for the number of total heterotrophic bacteria and extracellular digesting enzyme activities. In the 1989 spring period the number of heterotrophic bacteria in the sediment surface layer was increased more than 100 times at the maximum compared to that in the 1988 summer period. The proportion of fresh water bacteria to total heterotrophic bacteria was also higher in the spring period than the summer period. The extracellular digesting enzyme activities were higher in spring season than summer. Although the water content of sediment in the spring period was lower than that the summer period. the ash weight indicating organic material content was higher. These results means that the diameters of sediment particles were larger in spring than summer but the input of organic material into the sediment was greater. Based on these results bacterial distributions in the sediment layer of South Sea depend greatly on the season due to the effect of fresh water. During the spring season plankton could grow extensively owing to the inorganic nutrients input by the vertical mixing in the water column, then be precipitated into the sediment. Organic nutrients supplied from enzymatic degradation of polymeric particle from plankton can increase the bacterial number, too.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.270-275
• /
• 2006

The cultivated pearls collected for the study were pretreated through the removal of contaminants and the surface bleaching for easy dyeing. Coloring of pearls are necessary after selecting dyes adsorbable to the Conchiolin layer, a kind of hard protein formed in the seawater, covering the surface of the pretreated pearls. Dyes adsorbable to the Conchiolin layers are mostly basic dyes such as Rhodamine 6G(R6G), Rhodamine B(RB), Methylene Blue(MB) etc. and the binary and ternary competitive adsorption were performed by mixing two or three dyes together. The multi-dye adsorption data were compared with the predictions from the ideal adsorbed solution theory(IASI) combined with the single-dye adsorption model, the Langmuir or the Redlich-Peterson(RP) model. The quality of prediction was compared by using determination coefficient($R^2$) and standard deviation(SSE) values. Predictions from the IAST were found to be in good agreement with the data for the R6G/RB binary adsorption to the pearl layers not fractionated with their size, except for the adsorption data for RB at high concentrations. Among the three binary adsorption systems, R6G/RB, R6G/MB, and MB/RB, only the RB sorption data in the R6G/RB binary system was in poor agreement with the IAST prediction. Competitive adsorption data in ternay systems were in good agreement with the predictions from the IAST except for the RB data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.477-477
• /
• 2008

For more than three decades, the gate dielectrics in CMOS devices are $SiO_2$ because of its blocking properties of current in insulated gate FET channels. As the dimensions of feature size have been scaled down (width and the thickness is reduced down to 50 urn and 2 urn or less), gate leakage current is increased and reliability of $SiO_2$ is reduced. Many metal oxides such as $TiO_2$, $Ta_2O_4$, $SrTiO_3$, $Al_2O_3$, $HfO_2$ and $ZrO_2$ have been challenged for memory devices. These materials posses relatively high dielectric constant, but $HfO_2$ and $Al_2O_3$ did not provide sufficient advantages over $SiO_2$ or $Si_3N_4$ because of reaction with Si substrate. Recently, $HfO_2$ have been attracted attention because Hf forms the most stable oxide with the highest heat of formation. In addition, Hf can reduce the native oxide layer by creating $HfO_2$. However, new gate oxide candidates must satisfy a standard CMOS process. In order to fabricate high density memories with small feature size, the plasma etch process should be developed by well understanding and optimizing plasma behaviors. Therefore, it is necessary that the etch behavior of $HfO_2$ and plasma parameters are systematically investigated as functions of process parameters including gas mixing ratio, rf power, pressure and temperature to determine the mechanism of plasma induced damage. However, there is few studies on the the etch mechanism and the surface reactions in $BCl_3$ based plasma to etch $HfO_2$ thin films. In this work, the samples of $HfO_2$ were prepared on Si wafer with using atomic layer deposition. In our previous work, the maximum etch rate of $BCl_3$/Ar were obtained 20% $BCl_3$/ 80% Ar. Over 20% $BCl_3$ addition, the etch rate of $HfO_2$ decreased. The etching rate of $HfO_2$ and selectivity of $HfO_2$ to Si were investigated with using in inductively coupled plasma etching system (ICP) and $BCl_3/Cl_2$/Ar plasma. The change of volume densities of radical and atoms were monitored with using optical emission spectroscopy analysis (OES). The variations of components of etched surfaces for $HfO_2$ was investigated with using x-ray photo electron spectroscopy (XPS). In order to investigate the accumulation of etch by products during etch process, the exposed surface of $HfO_2$ in $BCl_3/Cl_2$/Ar plasma was compared with surface of as-doped $HfO_2$ and all the surfaces of samples were examined with field emission scanning electron microscopy and atomic force microscope (AFM).