• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• 상하수도학회지
• /
• 제21권6호
• /
• pp.717-726
• /
• 2007

Fully-grown flocs in a mixing tank of membrane filtration with dead-end membrane are ruptured while passing through a pump and the ruptured flocs are aggregated again in a Membrane-Feed-Pipe (MFP). To look at more details, this study tries to relate the reaggregation to a parameter of mixing intensity in MFP, i.e., G-value. The G-value is a function of Reynolds number, pipe diameter, friction factor and average velocity in MFP. To deal with polydispersity condition, we develop a representative particle size called in this study EDPD (Effective Diameter for Polydispersity condition in Dead-end filtration). The experimental results show that as the G-value increases, the EDPD decreases and also the cake resistance increases. Through comparison between EDPD and cake resistance, these results show that cake resistances are controlled by reaggregation phenomenon in MFP. The effect of detention time in MFP, however, does not affect the reaggregation of the broken flocs as G-values are increased.

• 열처리공학회지
• /
• 제36권1호
• /
• pp.33-39
• /
• 2023

In this study, the effect of mixing condition of raw material powders possessing various particle size and particle size distribution on thermite reaction efficiency was investigated. When fine raw powders are used, rather the reaction yield tends to decrease due to agglomeration. In contrast, coarse raw powders make deteriorate the contact area between raw material powders containing Al reducing agent. To ensure the optimal thermite reaction efficiency, it is required to optimize a mixture condition of raw material powders prior to thermite reaction. From the current experiment, the maximum thermite reaction efficiency is 77%, which came from Nb₂O₅ + NiO +Al mixtures with size distribution from 9.25 to 22.63 ㎛.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5721-5727
• /
• 2015

페인트는 외부로부터 본체가 손상되는 것을 막아주며, 오랫동안 색깔과 마무리 상태를 유지해 준다. 유기용제와 물이 페인트의 용제로 사용되고 있으며, 유기용제는 VOCs의 인위적인 공급원으로 알려져 있다. 이러한 이유로 자동차 내장부품에서 유기용재 페인트의 사용은 줄어들고 있으며, 외장 부품에서는 계속 사용하고 있다. 수성페인트의 접착력은 유성페인트에 비하여 작아, 페인트가 기제로부터 박리되고 있어, 품질문제를 일으킨다. 본 연구에서는 수성페인트와 실린 혼합물의 접착 특성에 대하여 연구하였다. 수성페인트의 접착력을 향상시키기 위하여 접착제와 혼합이 필요하다. 접착력은 UTM을 이용하여 ASTM D1002 방법으로 측정하였고, 박리현상은 ASTM D1002를 사용하여 측정하였다. 수성페인트와 실란접착제의 최적 혼합조건은 $25^{\circ}C$, 500rpm, 20분 이었으며. 실란접착제 농도는 5wt% 이었다

• 한국식품영양과학회지
• /
• 제30권6호
• /
• pp.1102-1107
• /
• 2001

호박추출물, 고춧가루 및 메주를 이용하여 호박고추장을 제조할 때 가장 우수한 관능적 품질의 배합조건을 설정하고자 중심합성계획에 의한 반응표면분석법으로 모니터링하였다. 호박고추장의 색상에 대한 관능평점의 최대 배합비율은 호박추출물 함량 433.63 g, 고춧가루 함량 81.76 g 및 메주 함량 17.03 g 에서 그 관능점수가 가장 높았다 향에 대한 최적 관능조건은 호박추출물 함량 437.07 g, 고춧가루 함량 83.65 g, 메주 함량 11.90 g에서, 맛에 대한 관능평점은 호박추출물 함량 382.94 g, 고춧가루 함량 63.44 g, 메주 함량 13.10 g에서, 전반적인 기호도에 대한 관능평점은 호박추출물 함량 442.04g, 고춧가루 함량 62.58 g, 메주 함량 16.30 g에서 그 관능점수가 가장 높았다. 호박고추장의 최적 배합비율은 호박추출물 442.04 g, 고춧가루 62.58 g 메주가루 16.30 g이었다.

• 한국지반공학회논문집
• /
• 제33권11호
• /
• pp.97-104
• /
• 2017

벤토나이트와 현장토를 혼합하여 차수재료로 폐기물 매립장의 차수층에 많이 적용하고 있다. 차수층으로 사용되는 재료는 일반적으로 투수계수가 $1{\times}10^{-7}cm/s$ 이하인 재료를 사용한다. 벤토나이트를 현장에서 차수층 재료로 사용될 때 벤토나이트는 건조-수축 균열 발생 및 염수조건에서 팽창성 떨어지고 차수 기능을 상실하는 등의 문제점이 존재한다. 벤토나이트의 문제점을 극복하기 위해 본 연구에서는 균열 방지 및 해수조건에서 차수성을 확보할 수 있는 내염성 벤토나이트를 개발하였고, 건조수축균역 시험, 팽윤도 시험, 다짐시험 및 투수실험을 통해 내염성 벤토나이트의 혼합비 결정 및 성능을 평가하였다.

• 한국연소학회지
• /
• 제20권2호
• /
• pp.40-45
• /
• 2015

This study is aimed to study combustion characteristics of low $NO_X$ burner using petroleum cokes as fuel. The petroleum coke, which is produced through the oil refining process, is an attractive fuel in terms of its high heating value and relatively low price. But petroleum coke is a challenging fuel because of its low volatile content, high sulfur and nitrogen content, which give rise to undesirable emission characteristics and low ignitability. The petroleum cokes burner is operated at fuel rich condition, and overfire air are supplied to achieve fuel lean condition. The low $NO_X$ burner is designed to control fuel and air mixing to achieve air staged combustion, in addition secondary and tertiary air are supplied through swirler. Air distribution ratio of triple staged air are optimized experimentally. The result showed that $NO_X$ concentration is lowest when overfire air is used, and the burner function at a fuel rich condition.

• 펄프종이기술
• /
• 제31권4호
• /
• pp.69-75
• /
• 1999

This study was performed to investigated the application of mixed resins for corrugated container board. The corrugated container board yields a sandwich structure in which a linerboard material is glued to a corrugated medium . Now, manufacturing corrugated container boards don't provide sufficient strength, and result in box failure during shipping . Therefore improvement of box strength is necessary . In this study, we intend to improve box strength by improving corrugated medium strength with mixed resins and to find the optimum treatment condition of this resins. First, we tried to mixed resins as Starch+CMC, Starch_Irea, CMC+Urea, Second, investigated to applicability of this resins for corrugated medium , and the third, measured tensile index, burst index, and edgewise compression index on liner, medium paper, and single faced corrugated container board. In this test results, we obtained that the improvement ratios of tensile index in liner and medium paper were approximately 80-185%, 60-118% , respectively. The respecting improvement ratios of edgewise compression index of single faced corrugated container board was approximately 91-124%, relatively. In addition, we concluded that optimum condition in mixing ratio was 1 :3 with CMC + Urea and the ap[plication amounts was 9% on materials. Fro manufacture of corrugated container board, optimum condition in mixing ratio was 1 : 3 with 5% CMC +Urea , because of considering to improvement of strength on cost.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권3호
• /
• pp.269-275
• /
• 2014

본 연구는 PI 개념에 근거한 수처리용 인라인 혼화 및 응집 시스템의 성능특성에 대한 실험적 연구를 목적으로 한다. 3단 인라인 혼화 및 응집 시스템은 처리 원수 저장조, 응집제 주입 정량펌프, 혼화 및 응집관, 침전조 및 제어 판넬로 구성된다. 동일한 응집제와 응집보조제의 주입량 조건에서 응집제의 증가에 따른 탁도 제거율에 비해 응집보조제의 증가에 따른 탁도 제거율이 약 3배 정도 높게 나타났다. 동일한 혼화 및 응집 시간 조건에서 인라인 방식이 기계식에 비해서 평균적으로 약 4.6배 정도 탁도 제거율이 높게 나타났다.

• 한국물환경학회지
• /
• 제23권1호
• /
• pp.111-121
• /
• 2007

The experimental design and response surface methodologies haven been applied to the investigation of the chemical coagulation of livestock wastewater. The chemical coagulation reactions were mathematically described as a function of parameters raping mixing (rpm) of chemical coagulation ($X_1$), slow mixing (rpm) of chemical coagulation ($X_2$), $FeCl_3 $ concentration (mg/L) ($X_3$) and pH ($X_4$) being modeled by use of the central composite design. Empirical models were developed to describe relationship between the experimental variables and response. Statistical analysis indicates that three factors ($X_1$: raping mixing (rpm), $X_2$: slow mixing (rpm), $X_3$: $FeCl_3 $ concentration (mg/L) on the linear term (main effect), slow mixing (rpm) (${X_2}^2$) on the non-linear term (quadratic), and two factors ($X_1-X_3$, $X_2-X_3$) on the non-linear term (cross-product) had significant effects, respectively. The estimated ridge of maximum responses and optimal conditions for CODcr using canonical analysis was 87.44% ($X_1$: 229 rpm, $X_2$: 51 rpm, $X_3$: 877 mg/L, $X_4$: 4.3). To confirm this optimum condition, three additional experiments were performed and the mean CODcr removal (%) and concentration (mg/L) with a standard deviation of $87{\pm}1.2%$ ($576{\pm}34ppm$) were obtained.