• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.353-362
• /
• 2022

The wet shotcrete refers to a method in which all materials are mixed and then supplied to the spraying device, compressed air is added to the nozzle, and the spraying speed is improved to spray on the target surface. In order to reproduce the amount of shotcrete used in the wet method in the field and the situation at the laboratory scale, it is essential to control the discharge amount of the equipment. In this study, in order to increase the reproducibility of field conditions at the laboratory scale, a flow control system for shotcrete mortar spraying equipment was developed and applied to the equipment. To verify the developed equipment, a discharge control test using water and mortar was performed. In the developed control system, the discharge was smoothly controlled according to the user input value for the mono pump, but the discharge was not properly controlled according to the input value for the screw pump because of a reducer. When a speed reducer is attached, it is necessary to adjust the operation rate of the screw pump close to the target flow rate by increasing the operation rate of the screw pump while lowering the operation rate of the mono pump.

• Journal of the Korean Institute of Rural Architecture
• /
• v.23 no.1
• /
• pp.1-8
• /
• 2021

In this study, a real-sized experimental equipment (pilot plant) was built at the site based on the preliminary research data to develop a movable separator for the mixed construction waste that can be implemented in agricultural areas to review its feasibility through the evaluation of its separation efficiency by waste types. The final construction of the movable separator and experimental results of the separation efficiency are summarized as follows. 1) The separation performance according to the blade type was the best for the combustible wastes either with 26 numbers of L-type blades and 32 numbers of pin type blades. As far as combination of blade types, when the L-type and pin-type were combined, the best separation efficiency was achieved. 2) The separation efficiency for waste wood by the conveyor type and angle of inclination (slope) of the trommel was the best when the conveyor had ribs of seagull shape with the angle of inclination 45°. 3) The separation efficiencies by process showed that 65.9% was separated as inorganic demolition wastes, 18.2% as waste woods, and 16.0% as combustible wastes at conveyor speed of 2-3 rpm, and the error rate was the least from the waste types generated in the dismantle site.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.4
• /
• pp.8-15
• /
• 2015

The demand for environmental consideration is on the increase in civil engineering. This study focuses on the development of technology to reduce the use of carbonate cement and improve its performance by using a silicate mineral and hardening agents, and presents the test results for the demonstrative evaluation of the properties of the raw material. Highly active feldspar was used as a binder to augment the bonding of the carbonate cement, and their change in strength was observed after test piece construction with the addition of soluble hardening agent. The uniaxial compression strength of the test piece of the general Portland cement with the addition of 0.5% soluble hardening agent, showed an increase by 33% and that of the test piece of cement with the addition of 70% substituted with feldspar increased by 28%. The strength of viscous soil; classified as soft ground, showed an increase of a maximum of 1.7 times when it was mixed with cement and solidifier depending on the curing period. These tests confirmed that a soluble solidifier is effective for improving the strength of a cement binder and that the highly active feldspar can be used as a binder.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.330-337
• /
• 2021

3D printing is not only at the fundamental study and small-scale level, but has recently been producing buildings that can be inhabited by people. Buildings require a lot of cost and labor to work on the form work, but if 3D printing is applied to the building, the construction industry is received attention from technologies using 3D printing as it can reduce the construction period and cost. 3D printing technology for buildings can be divided into structural and non-structural materials, of which 3D printing is applied to non-structural materials. Because 3D printing needs to be additive manufacturing, control such as curing speed and workability is needed. Since cement mortar has a large shrinkage due to evaporation of water, cement polymer dispersion is used to improve the hardening speed, workability, and adhesion strength. The addition of polymer dispersion to cement mortar improves the tensile strength and brittleness between the cement hydrate and the polymer film. Cement mortar using polymer materials can be additive manufacturing but it has limited height that can be additive manufacturing due to its high density. When light-weight materials are mixed with polymer cement mortar, the density of polymer cement mortar is lowered and the height of additive manufacturing, so it is essential to use light-weight materials. However, the use of EVA redispersible polymer powder and light-weight materials, additional damage such as cracks in cement mortar can occur at high temperatures such as fires. This study produced a test specimen incorporating light-weight materials and EVA redispersible polymer powder to produce exterior building materials using 3D printing, and examined flame resistance performance through water absorption rate, length change rate, and cone calorimeter test and non-flammable test. From the test result, the test specimen using silica sand and light-weight aggregate showed good flame resistance performance, and if the EVA redispersible polymer powder is applied below 5%, it shows good flame resistance performance.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.11
• /
• pp.1796-1800
• /
• 2015

Sporopollenin is a poorly characterized mixed aliphatic and aromatic polymer with ester and ether linkages. Recent studies have reported that α-pyrone polyketide compounds generated by Arabidopsis thaliana, polyketide synthase A (PKSA) and tetraketide α-pyrone reductase 1 (TKPR1), are previously unknown sporopollenin precursors. Here, the yeast Saccharomyces cerevisiae was introduced to test potential sporopollenin biosynthetic pathways in vivo. A PKSA/TKPR1 dual expressor was generated and various chain-length alkyl α-pyrones were identified by GC-MS. The growth rate of the strain containing PKSA/TKPR1 appeared normal. These results indicate that PKSA/TKPR1-expressing yeast would be a starting platform to investigate in vivo sporopollenin metabolism.

• Computers and Concrete
• /
• v.25 no.1
• /
• pp.59-65
• /
• 2020

The premise for the study reflected in this article is the need to dispose of industrial waste, which is increasingly being used in the construction materials industry. Also, dynamically developing building industry demands attention of scientists and a direction of their works on improvement of the technology of carrying out construction works. Thus, the article is devoted to studying the influence of various chemical additives and fine fillers (industrial wastes) available in Kazakhstan on self-compacting concrete (SCC) mixtures and its rheological, physical, and technical properties. According to the studies, revealed the most efficient type of fine-dispersed filler and the most optimal type of chemical additive to enable obtaining a high-quality SCC mixture based on local raw materials. As a result, the use of microsilica in comparison with other industrial wastes resulted in a conglomerate with high compressive strength of SCC at early terms of curing. In terms of economic efficiency and quality improvement, the results of study are of practical value for the manufacturers of ready-mixed concrete operating in Kazakhstan.

• Nuclear Engineering and Technology
• /
• v.30 no.1
• /
• pp.26-39
• /
• 1998

The containment pressure and temperature transient analysis computer code CONTEMPT4/MOD5 is modified to incorporate the passive containment cooling models. The correlations are selected from the existing experimental heat transfer correlations to model the natural and mixed convection in annular space between the containment shell and the shield building. The evaporative heat transfer of the water film on the outer shell of the containment is modeled using the correlations derived from the analogy between the heat and mass transfer. The modified code is applied to the Ap600 containment transient analysis for the model verification and the results are compared to the results of GOTHIC calculation done by Westinghouse. Also, d series of parametric sensitivity studies of heat transfer correlations, water film ratio and delay time of the wet cooling on the containment peak pressure and temperature following LOCA are performed for the containment of 1000MWe passive plant, KP1000.

• Nuclear Engineering and Technology
• /
• v.42 no.3
• /
• pp.313-318
• /
• 2010

Alnine pellets were installed in a nuclear power plant for one or two operation cycles and measured by electron spin resonance (ESR) spectrometers for dosimetry. Dose and "x/y ratio", i.e., satellite peak over main center peak ratio, were measured for the returned alanine dosimeters from the nuclear power plant and compared to the values of reference alanine dosimeters exposed only to gamma rays. The variation of the x/y ratio change depended on the population of radicals from each radiation component with different LET. The gamma dose in a mixed radiation field was estimated by an additive gamma ray irradiation experiment and the measured dose rate at specified locations in the containment building.

• Journal of Digital Convergence
• /
• v.17 no.1
• /
• pp.169-177
• /
• 2019

The city is experiencing various problems such as traffic congestion, environmental pollution, urban crime, and faces the limit of growth. Recently, various attempts to build a Smart City have been spreading around the world, in order to solve these problems. Smart City is attracting attention as the core platform of the future city with the $4^{th}$ industrial revolution. However, various definitions of smart city are mixed, and the methods and strategies for implementing smart city are changing or evolving due to the development of technology and the experience during that time. This study summarizes the definition of various smart city through literature review and suggests smart city building strategy that enables sustainable growth of cities as a platform of the $4^{th}$ industrial revolution era.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.4
• /
• pp.489-497
• /
• 2022

In this study, the fluidity, mechanical properties and microstructure of cement pastes with carbon nanotube (CNT) were experimentally investigated. The 6 types of cement paste mixes with different PCE:CNT and w/b had been manufactured, and several tests including flow, compressive strength, absorption and water porosity were performed on cement pastes with or without CNT.Additionally, microstructural observations such as x-ray diffraction (XRD) and scanning electron microscopy (SEM) were carried out to examine hydrates formed in cement paste with CNT. As a result, it was found that the performance of cement pastes with CNT was better compared to that of control cement paste (OPC) due to both of hydration acceleration effect and filling effect. Furthermore, the SEM images clearly showed that CNT can bridge cracks formed in cement matrix. Conclusively, it is believed that the CNT, if mixed appropriately, could be an option as nono-materials to improve performance of concrete structures.