• Journal of the Korean Applied Science and Technology
• /
• v.15 no.4
• /
• pp.45-56
• /
• 1998

Methyl fructoside oleic acid polyester(MFPE), fructose-based sugar polyester, was synthesized by solvent-free, soap-free transesterification of methyl oleate with methyl fructoside(MF) as a sugar starting material in the presence of conventional potassium carbonate basic catalyst. Methyl fructoside was found to be an effective sugar starting material, because of its low softning point, high heat stability, high miscibility, and high reactivity than other sugars. Yield 98% of purified MFPE based on initial weight of MF was obtained at 1:5 of the molar ratio of methyl fructoside to methyl oleate, 2%(w/w) of potassium carbonate catalyst content, 20${\sim}$200mmHg of reduced pressure and $180^{\circ}C$ of reaction temperature. MFPE structure was confirmed by infrared and proton nuclear magnetic resonance spectroscopy. Physical properties of methyl of fructoside oleic acid polyester such as viscosity, HLB, solubility, color, refractive index, specific gravity, and density were similar to physical properties of sucrose polyesters(SPE) and vegetable oils. Then, it was elucidated that MFPE was sufficient to replace the SPE and conventional oils.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.2
• /
• pp.106-115
• /
• 2005

Bio-diesel as fatty acid methyl ester was derived from such oils as soybean, peanut and canola oil by lipase catalyzed continuous trans-esterification. So the activation of lipase(Novozym - 435) was kept to be up to 4:1, the limiting molar ratio of methanol to oil under one-step addition of methanol due to the miscibility of oil and methanol through the static mixer for 4hrs and the elimination of glycerol on the surface of lipase by 7wt% silica gel. Therefore the overall yield of fatty acid methyl ester from soybean oil appeared to be 98% at 50$^{\cdot}C$ of reaction temperature under two-steps addition of methanol with 2${\times}$2:1 of methanol to oil molar ratio at an interval of 5.5hrs, 7wt% of lipase, 24 number of mixer elements, 0.2ml/min of flow rate and 7wt% of silica gel.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.91-96
• /
• 2002

To explore the effects of intramolecular interactions within the copolymer on the phase separation behavior of polymer blends, copolymers having two different types of intramolecular interactions, i.e., intramolecular repulsion and intramolecular attraction were prepared . In this study, poly(styrene-co-methylmethacrylate) (P(S-MMA)) having intramolecular repulsion caused by positive interaction between styrene and MMA and poly(styrene-co-ethyl-methacrylate) (P(S-EMA)) and poly(styrene-co-cyclohexylmethacrylate) (P(S-CHMA)) having intramolecular attraction caused by negative interaction between styrene and methacrylate were blended with tetramethyl poly-carbonate (TMPC). The phase behavior of blends was examined as a function of copolymer composition and blend composition. TMPC formed miscible blends with styrenic copolymers containing less than certain amount of methacrylate. The phase separation temperature of TMPC blends with copolymer such as P(S-MMA) and P(S-EMA), first increases with methacrylate content, goes through a maximum and then decreases just prior to the limiting content of methacrylate for miscibility, while that of TMPC blends with P(S-CHMA) always decreases. The calculated interaction energy for TMPC-P(S-EMA) pair is negative and monotonically increases with EMA content of the copolymer. Such behavior contradicted the general notion that systems with more favorable energetic interactions have higher LCST, The detailed inspection of the lattice-fluid theory related to the phase behavior was performed to explain such behavior.

• Polymer(Korea)
• /
• v.38 no.4
• /
• pp.477-483
• /
• 2014

Poly(lactic acid) (PLA) and poly(${\varepsilon}$-caprolactone) (PCL) blends with various components for melt-blown non-wovens were prepared by a twin-screw extruder. Tributyl citrate (TBC) was added in order to improve the miscibility between PLA and PCL. The results showed that small circular particles of PCL were dispersed in PLA matrix uniformly. The addition of PCL had the heterogeneous nucleation effect on the crystallization of PLA and decreased thermal stability of PLA. The flow of pure PLA and blends approached to Newtonian liquid at a low shear rate and expressed more obvious viscoelasticity at a high shear rate.

• Fibers and Polymers
• /
• v.5 no.3
• /
• pp.239-244
• /
• 2004

Solution-cast films of polymethylmethacrylate (PMMA) and polyurethane (PU) containing polymeric styryl dye up to 5 % by weight were prepared to investigate their acid-sensitivity and mechanical and thermal properties. Original red samples due to styryl dye turned out yellow very rapidly as they were exposed to acid vapor of hydrochloric acid or p-toluenesulfonic acid. According to UV/VIS spectroscopic measurements, characteristic peak intensities near 430 nm and 520 nm increased or decreased relatively with exposed amounts of acid, respectively. Both PMMA and PU samples showed uniform color distribution due to a good miscibility between polymer and dye which can be evidenced by measurements of glass transition temperature. No significant difference in acid-sensitivity was found between PU and PMMA except relative absorbance. However, dependence of their mechanical properties on dye content was somewhat different with PU or PMMA. In case of PMMA, modulus and breaking stress increased up to about 50 % with increasing dye content, whereas those of PU samples showed only slight increase. It was ascribed to whether the matrix polymer was in the glassy or rubbery state.

• Macromolecular Research
• /
• v.10 no.5
• /
• pp.259-265
• /
• 2002

The cure kinetics of blends of epoxy (DGEBA, diglycidyl ether of bisphenol A)/anhydride resin with polyamide copolymer, poly(dimmer acid-co-alkyl polyamine), were studied using differential scanning calorimetry (DSC) under isothermal condition. On increasing the amount of polyamide copolymer in the blends, the reaction rate was increased and the final cure conversion was decreased. Lower values of final cure conversions in the epoxy/(polyamide copolymer) blends indicate that polyamide hinders the cure reaction between the epoxy and the curing agent. The value of the reaction order, m, for the initial autocatalytic reaction was not affected by blending polyamide copolymer with epoxy resin, and the value was approximately 1.3, whereas the reaction order, n, for the general n-th order of reaction was increased by increasing the amount of polyamide copolymer in the blends, and the value increased from 1.6 to 4.0. A diffusion-controlled reaction was observed as the cure conversion increased and the rate equation was successfully analyzed by incorporating the diffusion control term for the epoxy/anhydride/(polyamide copolymer) blends. Complete miscibility was observed in the uncured blends of epoxy/(polyamide copolymer) up to 120 $^{\circ}C$, but phase separations occurred in the early stages of the curing process at higher temperatures than 120 "C. During the curing process, the cure reaction involving the functional group in polyamide copolymer was detected on a DSC thermogram.gram.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.2
• /
• pp.1-8
• /
• 1999

The state of compatability of poly(vinyl alcohol)(PVA) and methyl cellulose(MC), prepared by an aqueous solution casting, were investigated over the entire compositions by dynamical mechanical analyzer(DMA) and differential scanning calorimetry(DSC). The glass transition temperatures of the blends, estimated by DMA, indicate that the blends of PVA and MC showed a definite degree of partial miscibility by showing two glass transition temperatures below 80 wt % MC contents in the blends and one glass transition temperature above 80 wt % of MC contents. The DSC results show a depression of melting point and crystallization temperature of PVA in the blends containing more than 80 wt % MC. This indicates that a considerable compatibility in the blend above 80 wt % MC contents may be attribute to the presence of interaction of hydroxyl groups of component polymers through hydrogen bonding. The DMA study of the effect of plasticizer on the polymers showed that water was a good plasticizer for PVA and PEG400 for MC. The addition of water and PEG400 in the blends showed a synergic plasticizing effect on these blends, which resulted in the large extent of the improvement of the compatibility. The elongation of PVA, MC and blonds was found to increase with addition of PEG400 in the blends, but the tensile strength to decrease with addition of plasticizer.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.4
• /
• pp.494-504
• /
• 2016

Eucalyptus oils are widely used as spices, perfume industrial materials, food flavorings, and medicines. Several types of Eucalyptus oils also have insecticidal activity and as carminative. This study investigated the chemical composition, insecticidal (larvicidal and repellent) activity of E. urophylla oil against filarial mosquito Culex quinquefasciatus. E. urophylla oil was obtained from fresh leaves by water-steam distillation with oil yield 1.08%. E. urophylla oil in this study had no color (clear), has odor (typical eucalyptus), with specific gravity 0.941; refractive index 1.465; miscibility in 70% ethanol 1 : 3; and optical rotation (-) $5.83^{\circ}$. The major compounds of the oil were ${\alpha}$-pinene (11.73%), 1,8-cineole (49.86%), ${\beta}$-ocimene (6.25%), ${\gamma}$-terpinene (9.11%), and ${\alpha}$-terpinyl acetate (7.63%). The result showed the excellent insecticide activity against C. quinquefasciatus. The oil provided larvicidal activity with $LC_{50}$: 80.21 ppm and $LC_{90}$: 210.18 ppm, and repellent activity with $IC_{50}$: 0.82% and $IC_{90}$: 4.88%. The present study showed the effectiveness of E. urophylla as natural insecticide against C. quinquefasciatus, the mosquito vector of filariasis.

• Applied Chemistry for Engineering
• /
• v.3 no.2
• /
• pp.247-255
• /
• 1992

Polystyrene-poly(caprolactone) (PS-PCL) block copolymer was synthesized from macroazoinitiator, and its compatibilizing effect in poly(2, 6-dimethyl-1, 4-phenylene oxide) (PPO)/poly(styrene-co-acrylonitrile) (SAN, 25wt% acrylonitrile) blend was studied. PS block and PCL block in the block copolymer had shown miscibility with PPO and SAN respectively. The dissolution of SAN into PPO domain was promoted by the addition of the PS-PCL block copolymer.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.973-978
• /
• 1997

The toughness and morphology of epoxy resin based on diglycidyl ether of bisphenol A(DGEBA) cured with of tris (dimethylaminomethy]) phenol(DMP-30) and castor oil (CO) as a toughening modifier have been studied. Mixtures of CO and an epoxy resin showed a higher miscibility than the classical CTBN modified epoxy resin. The glass transition temperature($T_g$) was decreased with the CO content and the cure temperature. It is interpreted that the networks of epoxy matrix obtained at high temperature are apparently looser and more flexible due to the lower crosslinking density. The toughness was slightly increased with the CO content at $40^{\circ}C$ of curing temperature. The toughness increased with increasing the cure temperature and CO content.