• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 광주전남지부
• /
• pp.103-106
• /
• 2006

Semiconductor laser diode has a reflective facet in a both-ends side fundamentally. Laser performance for improving, Anti-Reflection and High-reflection coating on the facet of semiconductor laser diode. To prevent internal feedback from both facets for realizing superluminescent diode and reducing the reflection-induced intensity noise of laser diode, it's key techniques are AR/HR coatings. In the study AR coating film were manufactured by Ion-Assisted Deposition(IAD) system. Then manufactured coating film measurement electrical properties(L-I-V, Se, Resistor) and Optical properties (wavelength FFP)

• Journal of the Optical Society of Korea
• /
• 제16권1호
• /
• pp.80-84
• /
• 2012

A high reflectance mirror, which has very low absorption and scattering loss, was coated onto a crystalline substrate by ion beam sputtering and then annealed at $450^{\circ}C$. We carefully selected the mirror coating material, and designed the high reflectance mirror, in order to avoid UV degradation which comes from the He-Ne plasma. We measured the surface roughness of the Zerodur substrate using phase shift interferometry and atomic force microscopy, and compared it with the TIS scattering of the mirror. The cavity ring-down method was used to measure the absorption of the mirror, and the thin film structure was correlated to its results. We also compared the optical properties of coated mirrors before and after annealing.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.56.2-56
• /
• 2001

For the improvement of minimum sensing angular velocity of ring laser gyro, the influence of a low-scattering mirror application to laser resonator was investigated. Super polishing technique was employed for the fine mirror substrates of less than 1-${\AA}$-rms roughness. Mirror coating using ion-beam sputtering coating machine produced low-scattering mirror less than 30-ppm scattering. As a result of the mirror application to ring laser, the minimum sensing angular velocity of the gyro was improved down to about 0.1 deg/sec.

• 한국산학기술학회논문지
• /
• 제21권1호
• /
• pp.439-447
• /
• 2020

망원경의 성능 유지를 위해서 중요한 것 중 하나가 미러의 재코팅이다. 미러에 코팅된 금속은 빛을 반사시키는 역할을 하며 반사율이 떨어지게 되면 망원경의 성능이 저하되므로 주기적으로 재코팅을 해야 한다. 군 무기체계로 개발되는 망원경은 성능 뿐만 아니라 임무 수행을 위한 무기체계 가용도와 장기간 사용을 위한 운용유지비 관점에서도 미러의 재코팅 주기를 예측하고 정비계획을 수립하는 것이 필요하다. 그러나 대부분 천문 연구용으로 사용되는 유사 망원경들은 예측이 아닌 경험치와 운용 환경에 따라 재코팅 주기를 결정한다. 따라서 본 연구에서는 시뮬레이션을 활용하여 무기체계로 개발되는 망원경 미러의 세척 주기와 재코팅 주기를 예측하였다. 첫째, 국내외 천문연구원들의 유사 사례를 분석 및 코팅의 필요성과 코팅 주기 예측의 필요성을 확인하였다. 둘째, 데이터 분석과 모델링을 통해 미러 세척 빈도와 코팅 주기를 예측하는 시뮬레이션을 설계하였다. 마지막으로 성능을 만족하기 위한 반사율 감소 조건을 5%, 10%, 15%, 20%로 설정하고, 세척 조건 3개월, 6개월, 1년, 2년 단위로 다양화 하여 해당 조건 별 세척 주기 및 재코팅 주기를 예측하였다. 이를 통해 본 연구는 군 무기체계로서 망원경을 개발하며 정비계획을 수립하는 데 참고할 수 있는 기준을 제시하였다.

• 한국안광학회지
• /
• 제8권2호
• /
• pp.111-117
• /
• 2003

국내외 썬글라스 반미러 코팅렌즈의 광학적 특성을 파악하기 위해, 분광광도계를 이용하여 반미러 코팅렌즈의 반사율을 측정하였으며, Macleod 프로그램을 이용해 계산한 결과와 비교 분석하였다. 또한 황금 색깔이 나는 TiN을 이용한 반미러 코팅렌즈를 설계하였고, 광학특성을 조사하였다. 반미러 코팅렌즈의 분석결과, 은색 투톤(two tone) 반미러 코팅은 금속 크롬(Cr)을 사용하였으며 경도를 증가시키기 위하여 크롬위에 $SiO_2$(또는 $Al_2O_3$)를 증착하여 사용하였다. 크롬 위에 증착되는 $SiO_2$의 두께는 10nm 정도가 적정한 것으로 판단된다. 칼라 반미러 코팅의 경우 디자인 결과는 각각 다음과 같다 ; blue 계열은 [air|$SiO_2$(66.3)|$TiO_2$(129.0)|$SiO_2$(62.9)|$SiO_2$(26.0)|$TiO_2$(120.3)|$SiO_2$(9.1)|glass]이며, gold 계열은 [air|$SiO_2$(60.6)|$TiO_2$(86.2)|$SiO_2$(13.5)|$TiO_2$(86.8)|$SiO_2$(214.38)|glass]이며, green 계열은 [air|$SiO_2$(74.3)|$TiO_2$(75.8)|$SiO_2$(44.3)|$TiO_2$(11.6)|$SiO_2$(160.8)|$TiO_2$(12.9)|$SiO_2$(183.3)|$TiO_2$(143.8)|glass]이며, silver 계열은 [air|$SiO_2$(21.2)|$TiO_2$(49.7)|$SiO_2$(149.3)|glass]이다. white 반미러 코팅인 경우는 [air|$SiO_2$(17nm)|$TiO_2$(43nm)(또는 $ZrO_2$)|$SiO_2$(87nm) polysiloxane($4.46{\mu}m$)|glass or CR-39]이며, 가시광선 영역(400~700 nm)에서 평균 19%의 반사율을 가지며 흡수가 적기 때문에 약 80%의 투과율을 보이는 white 타입의 반미러가 되게 된다. 황금빛 색깔을 띠는 반미러 코팅렌즈의 설계에 있어서 [air|$SiO_2$(170nm)|TiN(15nm)|glass]가 되면 CIE 좌표값은 거의 [air|Au(150nm)|glass]의 좌표값과 유사해지는 것을 볼 수 있었다.

• 한국안광학회지
• /
• 제13권1호
• /
• pp.53-58
• /
• 2008

목적: 안경렌즈용 소형 suptter coating system을 설계하고 제작하고자 한다. 방법: sputter system의 target 설계에 있어서 Essential Macleod thinfilm design software를 이용해 AR 코팅과 mirror 코팅이 동시에 설계 가능한 Si target 을 결정하였으며. 그 후 sputtering 장비를 제작하였다. 결과: $SiO_2$와 $Si_3N_4$의 5층 박막으로 구성되는 AR 코팅의 최적조건은 [air|$SiO_2$(81.3)|$Si_3N_4$(102)|$SiO_2$(19.21)|$Si_3N_4$(15.95)| $SiO_2$(102)|glass] 이였다. Mirror 코팅의 경우, blue color 코팅의 최적조건은 [air|$SiO_2$(56.61)|$Si_3N_4$(135.86)|$SiO_2$(67.64)| $Si_3N_4$(55.4)|$SiO_2$ (53.53)|$Si_3N_4$(51.28)|glass] 이고, green color 코팅의 최적조건은 [air|$SiO_2$(66.2)|$Si_3N_4$(22.76)|$SiO_2$(56.58)| $Si_3N_4$(140.35) |$SiO_2$(152.35)|$Si_3N_4$(70.16)|$SiO_2$(121.87)|glass] 이였으며, gold color 코팅의 최적조건은 [air|$SiO_2$(83.59)|$Si_3N_4$(144.86) |$SiO_2$(11.82)|$Si_3N_4$(129.93)|$SiO_2$(90.01)|$Si_3N_4$(88.37)|glass] 이였다. 결론: 코팅 시간을 줄여 안경단가를 줄이기 위하여 안경렌즈 코팅 시 렌즈의 전 후면을 동시에 코팅을 해야 하기 때문에 sputtering장비 설계를 할 때 안경렌즈 전면과 후면에 동일하게 Si target을 갖춘 cathode를 사용하였고, 렌즈의 곡률을 고려하여 각 층이 동일하게 코팅이 되어야 하기 때문에 target-substrate 간의 간격은 12.5 cm에서 20 cm로 가변할 수 있도록 설계하고 제작하였다. 고품질의 안경렌즈 코팅을 위하여 고진공 펌프로 turbo pump를 이용하였으며, 코팅박막의 균일함을 얻기 위해서 치구를 회전할 수 있도록 설계하고 제작하였다.

• 한국재료학회지
• /
• 제28권4호
• /
• pp.201-207
• /
• 2018

Infrared(IR) heating has many advantages, such as energy efficiency, reduced heating time, cleanliness, equipment compactness, high drying rate and easy automation. These features of IR heating provide widely industrial applications, such as surface heat treatment in semiconductor fabrication, thermoforming of polymers, drying and disinfection of food products, heating to metal forging, and drying of wet materials. In this study, the characteristics of a protected gold mirror were examined by spectrophotometer and the lifetime of the coating layers were evaluated by a cross-cutting method and salt spray test. The effects of manufacturing conditions on the protected gold mirror were seen and remedies for these effects were noted in order to improve the properties of the protected gold mirror in the drying process. The reflectance and lifetime of the protected gold mirror was influenced by manufacturing conditions, such as surface roughness and forming conditions of the anti-oxide layer, the adhesion layer, the reflecting layer and the protection layer. The results of this study showed that the protected gold mirror manufactured using a buffing method for pre-treatment resulted in the most effective reflectance. In addition, $Al_2O_3$ coating on an Al substrate as an anti-oxide layer was more effective than the anodizing process in the test of reflectance. Furthermore, the protected gold mirror manufactured by layers forming of various materials resulted in the most effective reflectance and lifetime when coated with $Al_2O_3$ as the anti-oxide layer, coated Cr as the adhesion layer, and coated $MgF_2$ as the protection layer.

• Journal of the Optical Society of Korea
• /
• 제10권2호
• /
• pp.57-62
• /
• 2006

Adaptive optics (AO) has been applied in various fields including astronomy, ophthalmology and high power laser systems. An adaptive optics system for a high power laser is not significantly different from other AO systems in the point of configuration except that high energy absorbed by the deformable mirror distorts the deformable mirror surface and so degrades system performance. Currently we are researching a bimorph deformable mirror for beam cleaning of a high power class laser. The bimorph mirror was considered to have 99% reflective coating and 1% absorption. So this paper first presents the temperature profiles and corresponding thermal distortions of the bimorph mirror faceplate when the mirror is under a high power lasing for 10 seconds. The analysis was accomplished by the use of finite difference and finite element computer programs to generate the element arrays, calculate the temperature profiles, and determine the structural deformations. Then this paper proposes an 'embedded wafer' type water-cooling system with derived cooling parameters.

• 정보저장시스템학회논문집
• /
• 제1권2호
• /
• pp.182-187
• /
• 2005

A large area micro mirror is an optical element that functions as changing an optical path by reflection in integrated optical system. We fabricated the large area silicon mirror by anisotropic etching using MEMS for implementation of integrated optical pickup. In this work, we report the optimum conditions to better fabricate and design, greatly improve mirror surface quality. To obtain mirror surface of $45^{\circ},\;9.74^{\circ}$ off-axis silicon wafer from (100) plane was used in etching condition of $80^{\circ}C$ with 40wt.% KOH solution. After wet etching, polishing process by MR fluid was applied to mirror surface for reduction of roughness. In the next step, after polymer coating on the polished Si wafer, the Si mirror was fabricated by UV curing using a trapezoid bar-type way structure. Finally, we obtained peak to valley roughness about 50 nm in large area of $mm^2$ and it is applicable to optical pickup using blu-ray wavelength as well as infrared wavelength.

• 전자공학회논문지A
• /
• 제32A권11호
• /
• pp.29-34
• /
• 1995

Mirror coating is applied to laser facets to improve properties of edge emitting laser diodes. In this experiment, InGaAsP/GaAs high power laser diodes were studied with respect to different degrees of anti-reflective coating. Sputterred $Al_{2}$O$_{3}$ was used as the coating material and the HR coating was kept constant at 90%. Threshold current density, differential quantum efficiency, emission wavelength and the operating current at 500mW were measured for a range of AR coating and compared with theoretically calculated values; that showed good agreements. Precise wavelength control is important for laser diodes for solid state pumping because of small absorption bandwidth. In addition, since these lasers operate under CW condition, a lowest possible operating current for a given power is desired in order to minimize the heat produced. From the results of this experiment, we were able to obtain a optimum range of AR coatings for minimum operating current. The wavelength can be varied up to 4nm within this range.