• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2941-2951
• /
• 2023

The optimal minimum ECCD power is evaluated numerically for completely suppressing the 3/2 and 2/1 NTMs in the CFETR hybrid scenario. For two typical frequencies of ECCD sources launching from two upper launcher (UL) ports, f_ec = 210 GHz and 240 GHz with O1-mode, UL₁: (R_i, Z_i) = (8.47, 5.7) m and UL₂: (R_i, Z_i) = (8.2, 4.5) m, higher frequency of ECCD source launching from the UL₂ port is better than that low frequency counterpart from the UL₁ port. Using 240 GHz ECCD source launching from the UL₂ port, the minimum power required to fully suppress the two NTMs with precise ECCD alignment is 12.4 MW and 16.7 MW, respectively. When good alignment cannot be achieved, the results suggest that the misalignment should not exceed 0.02α, preferably 0.015α, corresponding to 4.4 cm and 3.3 cm. Considering engineering difficulty of high-frequency gyrotron sources, the optimal minimum ECCD power with the 210 GHz source launching from the UL₂ port is 17.9 MW and 20.6 MW for completely suppressing the 3/2 and 2/1 NTMs, respectively. In view of this, it is a good choice to select the 210 GHz ECCD source launching from the UL₂ port in the short and medium term.

• Asian-Australasian Journal of Animal Sciences
• /
• v.9 no.6
• /
• pp.643-646
• /
• 1996

Experiments were conducted to determine potassium (K) requirement of mule ducklings. One-day-old ducklings with equal number of both sexes were fed diets containing graded levels of K for three weeks. In experiment 1, corn-soybean meal diet (CP 18.7%, ME 2,890 kcal/kg, K 0.80%) was used. The addition of K (0.00, 0.10, 0.20, 0.30, 0.40%) to the diet by potassium carbonate resulted in a decrease in weight gain and feed efficiency with the group fed on basal diet having the best performance. This means that the existing K in the basal diet is adequate for the growth of ducklings. In experiment 2, low K corn-isolated soy protein diet (K, 0.19%) was used. The supplementation of K (0.00, 0.16, 0.32, 0.48, 0.64%) resulted in an increase in weight gain and feed efficiency with the control group having the lowest performance. The minimum K requirement was found to be 0.49% for both maximum growth and best feed efficiency as determined by using bent-stick model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.125-129
• /
• 2005

Two kinds of physical treatments were examined for the analysis both of intrinsic surface and interior nature of CuInS $e_2$[CIS] and CuGaS $e_2$[CGS] films grown in separated systems. For the first method, a selenium protection layer which was immediately deposited after the growth of the CIS was investigated. The Se cap layer protects CISe surface from oxidation and contamination during the transport under ambient atmosphere. The Se cap was removed by thermal annealing at temperature above 15$0^{\circ}C$. After the decapping treatment at 2$25^{\circ}C$ for 60 min, ultraviolet photoemission and inverse photoemission measurements of the CIS film showed that its valence band maximum(VBM) and conduction band minimum (CBM) are located at 0.58 eV below and 0.52 eV above the Fermi level $E_{F}$, respectively. For the second treatment, an Ar ion beam etching was exploited. The etching with ion kinetic energy $E_{k}$ above 500 eV resulted in broadening of photoemission spectra of core signals and occasional development of metallic feature around $E_{F}$. These degradations were successfully suppressed by decreasing $E_{k}$ below 400 eV. CGS films etched with the beam of $E_{k}$ = 400 eV showed a band gap of 1.7 eV where $E_{F}$ was almost centered.st centered.

• Development and Reproduction
• /
• v.16 no.2
• /
• pp.87-93
• /
• 2012

Reproductive biology (maturation and spawning) of the female tongue sole Cynoglssus semilaevis were examined in 154 specimens caught from the west coast of Korea (between February and November 2010). Monthly changes of gonadosomatic index (GSI) and condition factor (CF) were peaked in September. Hepatosomatic index (HSI) showed a negative correlation with those of the GSI. Ovaries were classified into six stages based on the development of advanced oocyte and histological characteristics: virgin/immature, early developing, developing, late developing, ripe/spawning and spent/regressing stage. The relationship between fecundity (F) and total length (TL) of the fish was expressed as $F=251.43TL^{0.1264}$, and body weight (BW) was expressed as F=1130.4BW-880848. Biological minimum size of female was 46.87 cm (TL).

• The Journal of Korean Academic Society of Nursing Education
• /
• v.7 no.2
• /
• pp.264-274
• /
• 2001

About the patients who visited the emergency department of a hospital, investigative study was performed to assess and to classify them with triage tool, and to estimate the characteristics of them. 210 patients older than 15 years were investigated. Among them 11 patients who had responded inappropriately were excluded and remaining 210 patients were chosen as study subjects. Investigation had been performed for 30 days from Jan. 10, 2001 to Feb. 9, 2001. The triage tool was designed through the modification of triage tools developed by Kim and Choi. The data were analyzed with the SPSS program using mean, standard deviation, frequency, percentage, ANOVA and Scheffe's test. The results were as follows: 1. Of the characteristics of the study subjects, mean age of patients were 55.76 years and 70-79 years group which included 41 patients(20.6%) were most numerous. 101 (51.8%) patients visited emergency room by 119 emergency service and 91(45.7%) patients walked with assistance. 127 patients were cared in internal medicine department. 2. The distribution of triage scores were from minimum 6 points to maximum 18 points with mean $13.76{\pm}2.58$ points. 3. Triage scores had significant relationship with age(F=13.349,P=0.000), visiting method (F=8.832, P=0.000), walking status(F=28.185, p=0.000), care department(F=2.596, P=0.019), and preexisting disease(F=12.012, P=0.000). 4. After trage there were no urgent patient, 35 emergent patients(17.6%),109 subemergent patients(54.8%), and 55 nonemergent patients (27.6%). The result of emergency care were 80 admission(40.2%), 59 discharge (29.6%), 34 ICU admission(17.1%), 14 transfer to other hospital(7%), 10 operation (5%), and 2 death (2%). 5. About the time required for triage, mean duration to triage were $7.54{\pm}2.28$ mins in emergent patients, mean $7.23{\pm}2.50$ mins in subemergent patients and mean $6.49{\pm}2.19$ mins in nonemergent patients. There were no differences in duration to triage according to the severity of triage. 6. Time required in emergency treatment were mean $116.23{\pm}88.10$ in emergent patients mean $101.61{\pm}73.27$ in subemergent patients and mean $81.56{\pm}61.01$ in nonemergent patients. There were no significant difference among groups. This study depicted that triage scores were below the middle level and there were many geriatric patients in this hospital. Among the characteristics of patients, age, visiting method, walking status, care department, and accompanying disease could be data for triage of emergency patients. With triage score of a patient, the outcome of emergency care of a patient could be anticipated and this could be basal data in determining the priority of emergency nursing.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.2
• /
• pp.141-147
• /
• 2017

The purpose of this study is to develop an inorganic filling adhesive using MKP and borax based on Dead-burn magnesia and fly ash. First, basic experiments was conducted to derive the proper addition rate of MKP. And this experiment was carried out according to addition ratio of borax. The test items are measured for pot life, flexural strength, compressive strength, adhesive strength, tensile strength, ratio of temperature change, ratio of hardening shrinkage, radon gas and formaldehyde emission. As a result, the proper addition rate of phosphate was 35%. The pot time is about 10minutes, 15minutes and 25minutes according to addition rate of borax. The flexural strength and compressive strength were obtained at 12hours for minimum flexural strength of 8.0MPa and minimum compressive strength of 31.0MPa. The tensile strength was the least 4.1MPa, and the ratio of hardening shrinkage was maximum 2.4% and ratio of heat change was maximum - 0.3%, which satisfied all of the quality standards of 'KS F 4923' (epoxy resin for repairing concrete structures). Both Radon gas and formaldehyde emission was not detected.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.263-271
• /
• 2013

A low dropout regulator (LDO) with fast transient responses is presented. The proposed LDO eliminates the trade-off between slew rate and unity gain bandwidth, which are the key parameters for fast transient responses. In the proposed buffer, by changing the slew current path, the slew rate and unity gain bandwidth can be controlled independently. Implemented in $0.18-{\mu}m$ high voltage CMOS, the proposed LDO shows up to 200 mA load current with 0.2 V dropout voltage for $1{\mu}F$ output capacitance. The measured maximum transient output voltage variation, minimum quiescent current at no load condition, and maximum unity gain frequency are 24 mV, $7.5{\mu}A$, and higher than 1 MHz, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.157-162
• /
• 2003

An experimental investigation was conducted to study the behavior of high-strength RC wide beam-column joints with slab subjected to reversed cyclic loads under constant axial load. Six half scale interior wide beam-column assemblies representing a portion of a frame subjected to simulated seismic loading were tested, including three specimens without slab and three specimens with slab. The primary variables were compressive strength of concrete($f_ck$=285, 460kgf/$cm^2$), the ratio of the column-to-beam flexural capacity($M_r$=$\Sigma M_c / \Sigma M_b$ ; 0.77 -2.26), extended length of the column concrete($l_d$ ; 0, 12.5, 30cm), ratio of the column-to-beam width(b/H ; 1.54, 1.67). Test results are shown that (1) the behavior of specimen using high-strength concrete satisfied for required minimum ductile capacity according to increase the compressive strength, (2) the current design code and practice for interior joints(type 2) are apply to the wide beam-high strength concrete column.

• Journal of Digital Convergence
• /
• v.13 no.4
• /
• pp.417-423
• /
• 2015

Oil-in-water(o/w) nanoemulsions were prepared in the system of water/Span 80-Tween 80/long-chain paraffin oil via PIC method. With the increase of preparation temperature from 30 oC to 80 oC, the diameter of emulsion droplets decreased from 150 nm to 40 nm. By varying the HLB of mixed surfactants, we found that there was an optimum HLB around 13.0~14.0 corresponding to the minimum droplet size. The size of emulsion droplets increased upon increasing the ratio of oil/emulsifying agent. At $f{\leq}0.15$, the size of nanoemulsions could be kept constant more than 2 months. The increase in preparation temperature makes it possible for producing monodisperse nanoemulsions. Once the nanoemulsion is produced, the stability against Ostwald ripening is outstanding due to the extremely low solubility of the liquid paraffin oil in the continuous phase.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.177-188
• /
• 2001

This research was carried out to examine the optimum design conditions of a vertical small-scale milling machine where the rough rice is processed directly into the white rice in one pass. Effects of the main spindle speed, feed screw pitch and ceramic coating length of the roller on various milling characteristics such as white rice processing capacity, electric energy consumption, rice temperature increase, broken rice ratio, moisture reduction, outlet force and crack ratio increase were studied. The results are as follows. 1. The maximum white rice processing capacity and the lowest crack ratio increase, were obtained from a machine with specification: main spindle speed of 970rpm having a feed screw pitch of 19㎜. 2. The minimum electric energy consumption was obtained with the main spindle speeds of 900 and 970rpm respectively having a feed screw pitch of 19㎜. 3. The rice temperature was increased as the feed screw pitch decreased and the main spindle speed increased. 4. Broken rice ratio was relatively low with the range of 0.8∼1.3%. 5. Moisture content loss was with the range of 0.05∼0.4%. 6. The highest outlet force was 0.72kg$\_$f/ with 900rpm of the main spindle speed and 19㎜ of the feed screw pitch and the lowest outlet force was 0.18∼0.34kg$\_$f/ with 970rpm of the main spindle speed and 16㎜ of the feed screw pitch. 7. The optimum design conditions for the vertical small-scale milling machine were obtained at 970rpm of the main spindle speed, 19㎜ of the feed screw pitch and 20㎜ of the ceramics coating length.