• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.171-174
• /
• 2010

In the paper, a printed dual-dipole array antenna is presented. A 4-way planar SIW power divider is adopted for feeding the array antenna. The dual-dipole is adopted as radiation elements which greatly improves the impedance band. The measured bandwidth larger than 31 % for VSWR$\leq$1.5 operating near 14 GHz is achieved and in agreement with the simulated results. The radiation E-plane and H-plane radiation pattern is presented in the paper. The radiation gain is also presented in the paper.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.833-836
• /
• 1999

In this paper, a wideband MMIC LNA was designed using low Q matching network. Gains of 9.8~12.2 ㏈, and noise figures of 1.7~2.1 ㏈ were obtained from the fabricated wideband MMIC LNA in the frequency ranges of 1.5~2.5㎓. And maximum output power of 10.83 ㏈m were obtained at the center frequency of 2 ㎓. The chip size of the fabricated wideband MMIC low noise amplifier is 1.4 mm$\times$1.4 mm.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.98-105
• /
• 1996

The design method of 85 GHz-115 GHz band single side-band filter using the principle of martin-puplett inteferometer is described. It has been designed by this method and also manufactured and tested. From the test results, not only the ratio of image singal rejection of 19 dB is obtained, but also the theoretical and experimental results of center frequency of pass-band and rejection-band show the validity of the theory. This manufactured filter was installed on 100GHz band SiS (superconductor insulator superconductor ) receiver for observing cosmic radio waves and tested. We found that this filter can be used a single side-band as well as double side-band mode. The design method which is presented in this paper can be used a single side-band filter for a heterodyne type sub-milimeter wave receiver.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.53-58
• /
• 2014

The global automotive radar is regulated to use the 22GHz~26GHz band. However, it plans to move to the 77~81GHz band of a broadband radar in the millimeter wave for the high resolution of pedestrian sensing and blind spot. On the other hand, the 71~275GHz band is regulated to use a radio astronomy service. The interference is predicted between an automotive radar and a radio astronomy service. Therefore, this paper analyzed the interference impact of the automotive radar on the radio astronomy service and then obtained separation distance for the protection of the radio astronomy service.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.489-493
• /
• 1999

In this paper, an analysis of microstrip-slotline transition is performed using a 3D vector Finite Element Method(FEM). Artificial anistropic absorber technique is employed to implement an matching boundary condition in FEM. On the base of the analysis, power divider/combiner is designed. The structure of the power combiner already developed are Branch-line coupler, Rat-race coupler, Wilkinson coupler, Lange coupler, etc. Which are all planar, If the frequency goes up, the coupling efficiency of these planar couplers is decreased on account of skin loss. Especially, in millimeter-wave band, the efficiency of more than two ways combiner is radically reduced, so that application in power amplifier circuit is almost impossible, Microstrip-slotline transition structure is a power combining technique integrated into wave-guide, so that the loss is small and the efficiency is high. Theoretically, we can mount several transistors into the power-combiner. This makes it possible to develop a high power amplifier. The numerically calculated performances of the device that is, we believe, the best are compared to the experimental results in Ka-Band(26.5GHz-40GHz).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1318-1323
• /
• 2010

A lot of demand for parts of millimeter wave band, as would be expected 57~63 GHz band down conversion mixer was designed and fabricated using IHP 0.25 um SiGe process. Designed and fabricated mixer was double balanced type and located reduced 3D balun at RF port and buffer amplifier at outport for suppression LO signal and conversion gain. Fabricated mixer measured conversion gain of 13.8 dB, $P1dB_{in}$ -17 dBm and 88 mA of current consumption characteristics, respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.5
• /
• pp.1-9
• /
• 2011

Nowadays it is necessary to replace electrical wires with another intelligent connection method because the consumers, who have much experience with mobile smart devices, are expecting easier and smarter connectivity in their home electronics such as wireless linking. In this paper a bidirectional CEC control scheme is newly proposed to expand the controllability from one to two way in a millimeter band image transmission system because two degree of freedom controllability presents more intelligent convenience in HDMI interface systems. Experimental study shows the feasibility of the proposed system as an advanced image transmission solution in millimeter band including an intelligent 2 DOF CEC interface with the performance result of 3.0 Gbps transmission band for 1080p full-HD image steaming.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.600-605
• /
• 2003

We have experimentally demonstrated a Direct Optical Switching (DOS) CDMA for future wide-band mobile communication systems at the 40 ㎓ band by using orthogonal (crosscorrelation $\leq$2) unipolar type codes with code length of 16 and chip rate of 2.5 Gcps for radio-over-fiber (RoF) systems. Pulse-amplitude-equalized 40 ㎓ laser pulses were provided by rational-harmonically mode-locking a 10 ㎓ fiber ring laser.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.5
• /
• pp.99-103
• /
• 2022

Millimeter-wave tracking radars operate in various environmental restrictions, thus they demand stable power sources with low noise level under high fluctuation of input voltage. This paper presents the design and implementation of the compact power supply with max power of 727 W for Ka-band tracking radar applications. To meet requirements of voltage accuracy and system efficiency for transceiver circuits, upper plates of buck converters are attached on the covers of power supply for efficient heat dissipation. The proposed power supply achieves system efficiency of 88.4 %, output voltage accuracy of ±2 % and noise level of <1% under full load conditions.

• Journal of electromagnetic engineering and science
• /
• v.10 no.4
• /
• pp.316-321
• /
• 2010

This paper presents a novel fourth harmonic mixer with new structure. The traditional 3-ports fourth harmonic mixer and the novel fourth harmonic mixer are designed by ADS, HFSS and CST simulator. The mixers have been fabricated and tested. The size of the traditional 3-ports fourth harmonic mixer is $12{\times}15$ mm, and the best conversion loss is 18.7 dB according to the measurement. Since the traditional 3-port mixer size is too large to be ranked, we design a novel fourth harmonic mixer for imaging system. The width of the mixing module in the novel fourth harmonic mixer is only 3.65 mm, and this size is fully capable to meet the mixer unit space which is not greater than 5 mm. The simulation result shows that the mixer has good performance, and the experiment result shows that the best conversion loss of the novel fourth harmonic mixer is 16.3 dB at RF signal of 91.3 GHz.