• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.1
• /
• pp.27-37
• /
• 1994

To catch the relative importance of varietal and environmental variation in various grain quality components associated with palatability of cooked rice, grain appearance, milling recovery, several physicochemical properties of milled rice and texture or eating quality of cooked rice for rice materials of five japonica cultivars, produced at four locations of the mid-mountainous and alpine area of Korea in 1989, were evaluated and analyzed the obtained data. Highly significant varietal and locational variations were detected in 1000-grain weight, amylose content, K/Mg ratio, gelatinization temperature, peak viscosity, breakdown and setback viscosities as compared with variety x location interaction variation. Also, marked locational variations were recongnized in milling recovery from rough to brwon rice, alkali digestibility and protein content, and significant varietal variation was caught in stickiness /hardness ratio of cooked rice. The variety x location interaction variation was especially large in quality components of grain appearance and ripening, palatability of cooked rice and consistency viscosity. One thousand kernel weight was heaviest in Jinbuolbyeo and Odaebyeo, and the unfilled grain ratio was lowest in Jinbuolbyeo. Odaebyeo showed slightly' lower ratio of intact and clear milled rice because of more chalky rice kernels compared with other cultivars. Amylose content of Jinbuolbyeo and Sobaegbyeo was about 1% lower than that of others and K/Mg ratio of Odaebyeo was the lowest one among rice materials. Odaebyeo, Sobaegbyeo and Jinbuolbyeo revealed significantly low gelatinization temperature and setback viscosity while high peak and breakdown viscosities. Cholwon rice showed the greatest kernel weight, good grain filling but lowest ratio of intact and clear milled rice while Jinbu rices exhibited the highest milling recovery from rough to brown rice and ratio of sound milled rice. Amylose content of milled rice in Jinbu rices was about 2-3% lower than those in other locations. Protein content of polished rice was about 1% lower in rice materials of middle zone than those of southern part of Korea. K/Mg ratio of milled rice was highest in Jinbu rice and potassium content was slightly higher in the rice materials of middle region than in those of southern region. Alkali digestion value and gelatinization temperature of polished rice was markedly high in Jinbu rices as compared with other locations. Breakdown viscosity was hightest in Chlown rices and next higher with the order of Hwaso>Unbong>Jinbu rices, and setback viscosity was the quite contrary tendency with breakdown. The stickiness /hardness ratio of cooked rice was relatively higher value in Cholwon rices than in the others and the palatability of cooked rice was a little better in Unbong and Cholwon rices than in Jinbu and Hwaso rices, although variety x location interaction variation was large. The rice materials can be classified largely into two groups of Jinbu and the others by the distribution on the plane of 1st and 2nd principal components (about 60% of total informations) contracted from twelve grain quality properties closely associated with eating quality of cooked rice. Also, Jinbu and the other rices were divided into two and three rice groups respectively. Varietal variation of overall rice quality was smallest in Hwaso. The most superior rice group in overall quality evaluation included Odaebyeo produced at Cholwon, Unbong and Hwaso, and Sobaegbyeo grown at Unbong

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.331-331
• /
• 2017

This study was conducted to know the influence of air temperature and sunshine duration on yield, chemical component, pigment color difference and starch characteristics of two colored rice cultivars in the plain area of Yeongnam province in Korea. The $L^*$, $a^*$, and $b^*$ value of brown rice in Hongjinju and Josaengheugchal rice cultivars was significantly different at continuous cultivated years, 2015 and 2016. The $L^*$, $b^*$ value of two colored rice was significantly increased in 2016 compared to 2015. The $a^*$ value of Josengheugchal rice cultivar was also significantly higher at 2016 than at 2015. It can be noticed the $a^*$, $b^*$, $L^*$ values in Josaengheugchal varied more than those in Hongjinju. Air temperature during ripening period in 2016 was higher than 2015, especially minimum temperature was too high to proper maturation for rice quality. In Josaengheugchal rice cultivar, sunshine duration after heading was longer in 2016 than in 2015. On the contrary, Hongjinju rice cultivar was ripened under condition of insufficient sunshine duration in 2016. The short growing duration by high temperature and long shiny duration made the lack of pigment for Josaengheugchal brown rice. In Hongjinju rice cultivar, shorten sunshine duration and higher night temperature were the source of the pigment deficiency. The grain size of rice which produced in 2016 was bigger than that of 2015 in both rice cultivars. The 1,000 grain weight of rice from 2016 was also bigger than that of 2015. Head rice ratio was high in the rice cultivars produced in 2015. Protein of milled rice in 2016 was more decreased than that of 2015 in Josaengheugchal rice cultivar, it showed reverse result in Hongjinju rice cultivar. Amylose contents of milled rice in 2016 were more decreased than that of 2015 in Hongjinju rice cultivar. Branch chain length distribution of amylopectin was shown a distinct difference between Josaengheugchal and Hongjinju rice flours by each produced year. Josaengheugchal rice cultivar produced in 2015 had a higher amount of short chains than that of 2016 rice starches. In Josaengheugchal rice cultivar, the pasting temperature and peak, trough, breakdown, final viscosity increased in rice flour which produced at 2016, whereas the setback viscosity and peak time showed lower value than those of rice from 2015. The most pasting properties (except of setback viscosity) of rice starch in Hongjinju rice cultivar grown in 2015 were higher than those of rice cultivar produced in 2016.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.265-265
• /
• 2017

This study was carried out to develop rice variety integrated with rice bacterial blight resistance gene and to know the information of major agronomic traits of developed variety. Advanced backcross Lines 21 having Xa3 and Xa21 gene cross from japonica cultivar Hwanggeumnuri and indica variety IRBB21. Days after seeding and culm length of ABLs21 were 108 days (Aug. 16) and 76 cm, respectively. Ripened grain rates was 87.4 %, which was similar to the parents. 1000 grain weight of brown rice of ABLs21 was 21.4g, which was lower than the donor parent. Milled rice yield of ABLs21 was 532 kg/10a, which was smaller than recurrent parent and higher than the donor parent. Grain length/width ratio of brown rice was form of japonica with short-ellipse and glossiness of cooked rice has japonica trait. Head rice rate showed a large difference compare to the donor parent and similar to the recurrent parent. ABLs21 would be useful genetic resources for resistance breeding program against bacterial blight.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.2
• /
• pp.85-92
• /
• 1993

This study was investigated on the morphological characteristics of rice grain as affected by three fertilizer application treatments. Of no-nitrogen, optimum nitrogen, and heavy nitrogen without potassium in three regions of Suweon (Mid-West Plain Zone), Ichon(Mid-Inland Plain Zone), and Kyehwado(South-charyung Mts. Plain Zone) with four varieties, i.e., three Tonsil types(Geumgangbyeo, Milyang 23, and Chilseongbyeo) and one japonica type(Chucheongbyeo, Akibare in Japanese name). The results obtained were as follows: The increase of nitrogen application caused an increase of grain length in rough rice and grain width in milled rice, resulting in a decrease of the width/thickness ratio in milled rice. The width and thickness of rice grain produced in Kyehwado were smaller than those in the other regions. Therefore, the ratio of length/width and length/thickness in rice grain produced in Kyehwado was larger. The one thousand grain weight of rice was heavier at the optimum nitrogen level than at the no-nitrogen and heavy nitrogen without potassium treatment levels. The weight percentage of hull in rough rice grain decreased in accordance with the increase of nitrogen application, while the weight percentage of bran in brown rice was constant. This suggested that for the normal development of rice grain a constant ratio of bran is needed. The morphological change of rice grain by fertilizer treatments and the change of region cultivated could not be distinguished from the native characteristics of the variety. Other grain characteristics were discussed in view of treatment and regional effects.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.4
• /
• pp.452-457
• /
• 2009

The objective of this study was to provide fundamental data on breeding cultivar and cultural technique to identify quality characterization according to damage degrees in rice when are damaged at low temperature. For induction of cold damage, we treated the irrigation water at $17^{\circ}C$ from the panicle formation stage to the heading date. The rice products were harvested by grades according to the sterility ratio and investigated 5 items of quality analysis including ripened grain ratio, brown/rough rice ratio, 1000 grain weight of brown rice, protein content, and amylose content. The quality analysis were characterized by each items according to the sterility ratio. As a result, the ripened grain ratio was y=1.0444x-7.6597($R^2=0.9874^{**}$), protein content was y=-0.046x+10.875 ($R^2=0.6973^*$), and head rice ratio was y=-0.2306x+104.32 ($R^2=0.634^*$), but the amylose content, brown/rough rice ratio and the milled/brown rice ratio were not significant. The rice plants, which injured by the low temperature, had bad influence in the yield and quality. Consequently, the breeding of rice cultivar and development of cultural technique are required to improve its cold tolerance.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.253-253
• /
• 2017

Recently, strong interest in the well-being and healthy food trends lead a spreading of rice processing products such as rice noodles, rice breads, and rice cakes. However, most of rice varieties developed in Korea showed very limited processing properties in processing of noodles compare to that of wheat flour. Moreover, low competitiveness as a raw processing materials due to high price give poor evaluations for rice noodles processing. To cope those barriers, 'Saemimyeon' a Tongil type high yielding variety with a high amylose contents was developed in RDA. 'Saemimyeon' showed about 10~32 % of increase in yield as 7.08MT/ha and 26.7% of high amylose contents together with easy grinding property of 65.7% of high chalkiness ratio. The both of milled as well as brown rice of 'Saemimyeon' were well fit for processing properties in rice pasta where the contents of rice flour for rice pasta was 99% (1% of Tapioka starch was intermixed in to the rice flour). A spaghetti type for wet noodles and macaroni type for dry noodles were developed, respectively. Each of pasta were showed relatively more or less an equal quality and panel test compare to that of durum wheat pasta products. Finally, rice pasta products could suggest an alternative idea for a new rice processing items where rice noodles market was stagnant.

• Korean Journal of Breeding Science
• /
• v.43 no.5
• /
• pp.383-390
• /
• 2011

Near-isogenic lines (NILs) carrying bacterial blight resistance genes (Xa4, xa5 and Xa21) were developed in japonica rice using Suweon345 as genetic background. NILs were selected by gene specific DNA markers and inoculation of K1 or K3a race. NILs conferring Xa4 were resistant to K1, K2, K3, and moderately resistant to K3a. NILs conferring xa5 were resistant to K1, K2, K3, and K3a. NILs having Xa21 were susceptible to K1, while resistant to K2, K3 and K3a. Target genes of NILs with the genetic background of Suweon345 were also confirmed by using eleven Philippines races and International Rice Bacterial Blight (IRBB) NILs carrying Xa4, xa5 and Xa21. All NILs had no significant difference from their recurrent parents in the major agronomic traits except for panicle length and brown rice 1,000 grain weight. Heading date of NILs ranged from Aug. 10 to Aug. 11, which was similar to that of recurrent parent, Suweon345. Culm length, number of grains per panicle and ratio of ripened grain of NILs were similar to those of Suweon345. Milled rice of NILs was ranged from 4.82 to 4.93MT/ha. These NILs will be useful for improving resistance to K3a race of bacterial blight pathogens in Korean japonica cultivars.

• Applied Biological Chemistry
• /
• v.46 no.1
• /
• pp.46-49
• /
• 2003

Paddy and milled rice quality, milling characteristics, energy consumption of milling process were investigated using Dasanbyeo, Ansanbyeo, Hwaseongbyeo, Ilpumbyeo, and Donganbyeo varieties. Thousand grains weights of the varieties dried to 15% moisture content were 22.92-28.60 g, with Dasanbyeo being the heaviest. Optimum clearance of rubber roller for obtaining maximum dehulling recovery was 30% of each rice variety thickness. At that time, perfect brown rice ratios of Dasanbyeo, Ansanbyeo, Hwaseongbyeo, Ilpumbyeo, and Donganbyeo were 95.24%, 98.86%, 95.97%, 97.75%, and 97.31%, respectively, and showed no significant differences among varieties. Ratios of removed rice bran after two times milling ranged 70.93-91.38%, with Dasanbyeo showing the highest ratio, and the average head rice ratio was 92.87%.