• International Journal of High-Rise Buildings
• /
• v.7 no.4
• /
• pp.287-298
• /
• 2018

High strength steels have been widely applied in recent years due to high strength and good working performance. When subjected to fire conditions, the strength and elastic modulus of high strength steels deteriorate significantly and hence the load bearing capacity of structures reduces at elevated temperatures. The reduction factors of mechanical properties of high strength steels are quite different from mild steels. Therefore, the fire design methods deduced from mild steel structures are not applicable to high strength steel structures. In recent ten years, the first author of this paper has carried out a lot of fundamental research on fire behavior of high strength steels and structures. Summary of these research is presented in this paper, including mechanical properties of high strength steels at elevated temperature and after fire exposure, creep response of high strength steels at elevated temperature, residual stresses of welded high strength steel member after fire exposure, fire resistance of high strength steel columns, fire resistance of high strength steel beams, local buckling of high strength steel members, and residual strength of high strength steel columns after fire exposure. The results show that the mechanical properties of high strength steel in fire condition and the corresponding fire resistance of high strength steel structures are different from those of mild steel and structures, and the fire design methods recommended in current design codes are not applicable to high strength steel structures.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.6
• /
• pp.587-592
• /
• 2010

A numerical analysis of reactive flow in a MILD(Moderate and Intense Low oxygen Dilution) combustor is accomplished to elucidate the characteristics of combustion phenomena in the furnace with the variation of air fuel ratio. For the smaller magnitude of air injection velocity(10 m/s), the air flow could not penetrate toward upper part of furnace. On the other hand, the air flow suppresses the fuel flow for the case of air injection velocity 30 m/s. The air velocity 18 m/s is corresponding to the stoichiometric air flow velocity, and for that case, the air flows to relatively more upper part of the furnace when compared with the case of air injection velocity 10 m/s. The reaction zone is produced with the previous flow pattern, so that the reaction zone of the air injection velocity 10 m/s is biased to the air nozzle side and for the case of air injection velocity 30 m/s, the reaction zone is inclined to the fuel nozzle side. For the cases with the air injection velocities 16, 18, 20 m/s, the reaction zone is nearly located at the center between air nozzle and fuel nozzle. The maximum temperatures and NOx concentrations for the cases of air injection velocity 16, 18, 20 m/s are lower than the cases with air injection velocity 10, 30 m/s. From the present study, the stoichiometric air fuel ratio is considered as the most optimal operating condition for the NOx reduction.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.5
• /
• pp.325-331
• /
• 2011

A numerical analysis of reactive flow in a MILD(Moderate and Intense Low oxygen Dilution) combustor is accomplished to elucidate the characteristics of combustion phenomena in the furnace with the change of fuel and air nozzle position and air mass flow rate. For the case with the fuel nozzle located near center position of combustor, the reaction zone started at the fuel nozzle and had inclined shape toward combustor wall when the air mass flow rate was relatively smaller. On the other hand, the end of reaction zone moved toward center of combustor from combustor wall when the air flow rate was relatively larger. For the case with the air nozzle located near center position of combustor, the reaction zone started at the fuel nozzle and had inclined shape toward combustor wall when the air mass flow rate was relatively small, which was similar as the previous case with smaller air mass flow rate. On the other hand, the end of reaction zone moved toward combustor wall when the air flow rate was relatively larger. The maximum temperature increased as the air mass flow rate increasing for both cases, and the concentration of thermal NOx increased also from the previous reason of temperature characteristics. The concentration of NOx for the case with the air nozzle located near center position of combustor was considerably smaller than that for the case with the fuel nozzle located near center position of combustor. From the present study, the case with the air nozzle located near center position of combustor and theoretical air flow rate was the most effective condition for the NOx reduction and perfect combustion.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.68-76
• /
• 1986

The surface rolling method which is one of the plastic deformation processes increases the surface roughness and hardness of materials. In this study, three NACHI6000 ZZ bearing were used for surface rolling tool on the mild steel and high carbon steel. The purpose of this study is to investigate the effects of rolling speed, feed rate and contact pressure on the surface roughness. The following results have been obtained with the mild steel and high carbon steel. 1. The roller finishing method has increased surface roughness from 2.4 .mu.m Ra at initial ground surface to 0.17 .mu.m Ra-0.4 .mu.m Ra. 2. The contact pressure has influenced greatly on the surface roughness. There is an optimal contact pressure. 3. As the rolling speed and the feed rate decrease, the surface roughness improves. 4. The optimal contact pressure for the good surface roughness of SS40 and STC 3 has been at 213 Kgf/Cm$^{2}$ and 220 Kgf/Cm$^{2}$ respectively.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.22 no.3
• /
• pp.220-227
• /
• 2009

Acquired hypohidrosis is a rare condition of unknown pathogenesis, while idiopathic cholinergic urticaria is relatively common. We report the case of a 18-year-old male with idiopathic cholinergic urticaria and acquired hypohidrosis. He presented with an intermittent pruritic eruption precipitated by mild activity, such as mild exercise or laughing, for last 4 years. He was diagnosed with cholinergic urticaria associated acquired hypohidrosis, successfully treated by herbal medicine applied Gejimahwanggakban-tang(桂枝麻黃各半湯).

• Journal of the Korean Chemical Society
• /
• v.55 no.5
• /
• pp.776-780
• /
• 2011

A mild and efficient procedure for the synthesis of various 1,5-benzothiazepines were developed. This method provides an easy access for preparation of 1,5-benzothiazepine derivatives in the presence of 10 mol% catalyst of CAN under ultrasonic irradiation. This method provided clean conversion, mild reaction condition, no use of toxic solvent and shorter reaction time compared to other reported method.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.20 no.4
• /
• pp.17-24
• /
• 1983

In this study, it was investigated the distribution of residual stress in the direction of loading between the root and toe the load fillet welds for thick steel plate. Residual stress distributions are measured by sectioning method which is one of stress-relaxation technique in welded joint, and analyzed by two dimensional finite element method on thermo-elasto-plastic theory under plane stress condition. These are compared the results of F.E.M analysis with the experimental result by stress-relaxation techniques. As a results, the following conclusion were obtained. (1) In the no penetration fillet welded joint specimen using mild steel plate with 25mm in thickness, the residual stress of loading direction near the root was about $10kg/mm^2$ tensile. (2) The tensile residual stress has been observed in fillet region of the fillet joint by F.E.M. analysis method. (3) The range of compressive residual stress distribution from the root was largest in the case of 5mm root penetration.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.04a
• /
• pp.181-188
• /
• 1994

Generally, the structural material shows rate dependent behaviors, which require to constitute different strain-stress relations according to strain rates. Conventional rate- independent constitutive equations used in general purpose finite analysis programs are inadequate for dynamic finite strain problems. In this paper, a rate dependent constitutive equation for elastic-plastic material was developed. The plastic stretch rate was modeled based on slip model with dislocation velocity and density so that there is no yielding condition, and no loading conditions. Non-linear hardening rule was also introduced for finite strain. Material constants of present constitutive equation were determined by experimental data of mild steel. The constitutive equation was applied to uniaxile tension. It was appeared that the present constitutive equation well simulates rate dependent behaviors of mild steel.

• Journal of Conservation Science
• /
• v.3 no.1 s.3
• /
• pp.23-30
• /
• 1994

This thesis researched for the conservation of a suit of armor that General Jung, Choong Sin had been worn in the 17th century, and of military uniform that was in perfect condition even though it had been underground for over 300years since 1676. As the armor was made with silk and cotton, it was treated by the dry cleaning method and the mild charge system. In the dry cleaning method, the used solvents were n-hexane and n-decane. And the percentage of the dry soap was 2 in the mild charge system. As the military uniform was made with only silk, it was treated by the dry cleaning method through the solvent of n-hexane and n-decane. Armor was repaired by scoured hemp partially, but military uniform became too deteriorated seriously to repair.

• The Korean Journal of Pain
• /
• v.5 no.1
• /
• pp.76-79
• /
• 1992

Trigeminal neuralgia is a condition characterized by excruciating paroxysms of pain in lips, gums, cheek, or chin, and very rarely, in the distribution of the ophthalmic division of the trigeminal nerve. There are many treatments of trigeminal neuralgia, such as, medical treatment, electrical stimulation, radiation therapy and ablative procedures. Infraorbital nerve block with pure ethyl alcohol is an ablation procedure for trigeminal neuralgia. We injected pure ethyl alcohol into the infraorbital foramen for pain control. The results were as follows; 1) The infraorbital nerve block with pure alcohol was an a simple and an effective method. 2) Complication, included a mild sensory deficit and mild edema over the infraorbital area.