• Journal of the Korean Ceramic Society
• /
• v.35 no.11
• /
• pp.1197-1202
• /
• 1998

To check the possibility for microwave sintering of MLCC(multi layer ceramic capacitor) the tape cast-ed BaTiO3 thick films in zirconia insulation box were sintered by the domestic microwave oven. Microwave sintered samples had higher density lower porosity than coventionally sintered ones. but they didn't show Z5U electrical properties due to short sintering time about 15 minutes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.702-706
• /
• 2014

A comparative study has been attempted for microwave and conventional sintering of lead-free $Bi_{0.5}Na_{0.5}TiO_3(BNT)$-based multilayer ceramic actuators(MLAs). It was found that microwave sintering (MWS) could be successfully applied to the co-firing of piezoceramic/AgPd MLAs with a 10 times shorter firing cycle as well as $100^{\circ}C$ lower firing temperature ($850^{\circ}C$) for sufficient densification than conventional furnace sintering ($950^{\circ}C$). Furthermore, MWS-derived specimens showed better electric field-induced strain than that of CFS-derived specimens by effectively suppressing interdiffusions between ceramic and electrode layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.439-442
• /
• 2004

The effects of sintering additives on the low-temperature sintering and microwave dielectric properties of $Mg_4Nb_2O_9$ dielectric ceramics were studied. When $3{\sim}20wt%$ of $0.242Bi_2O_3-0.758V_2O_5$ was added, the sintering temperature decreased from $1100{\sim}1300^{\circ}C$ to $950^{\circ}C$ and high density was obtained. When $Mg_4Nb_2O_9$ was sintered at $950^{\circ}C$ with 10wt% of sintering additive, the microwave dielectric properties of $Q{\times}f_0\;=\;80.035GHz,\;\epsilon_r\;=\;13.3\;and\;\tau_f\;=\;-12.9\;ppm/^{\circ}C$ were obtained.

• Journal of Technologic Dentistry
• /
• v.41 no.3
• /
• pp.195-201
• /
• 2019

Purpose: This study was investigated the effect of multilayer zirconia block type and sintering method on fracture strength, micro structure and color of zirconia copings. Methods: Three kinds of multi-layered zirconia blocks were used to identify the effects of the kinds of multi-layered zirconia blocks and sintering methods on fracture strength and color reproducibility of zirconia copings. 60 Zirconia copings were fabricated and fracture strength, micro structure and color reproducibility were compared and evaluated. Results: In all the blocks, the CS group, which refers to the general sintering method had higher fracture strength of zirconia copings than the MS group that refers to the microwave sintering method(MCS/MMS; 2,107.5N/1,930.4N, DCS/DMS; 917.0N/879.1N, UCS/UMS; 2,256.9/2,050.7N). In relation to CIE $L^*$, $a^*$, $b^*$ values of zirconia copings depending on the kinds of multi-layered zirconia blocks and sintering methods, the MS group using the microwave sintering method had lower brightness and chroma than the CS group using the general sintering method. Conclusion: In all the blocks, the CS group(general sintering) had higher fracture strength of zirconia copings than the MS group(microwave sintering). In relation to CIE $L^*$, $a^*$, $b^*$ values of zirconia copings depending on the kinds of multilayered zirconia blocks and sintering methods, the MS group using the microwave sintering method had lower brightness and chroma than the CS group using the general sintering method.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.43-48
• /
• 2007

This study is focused on the effect of the surface properties for the post electrode, which is used in pad formation consisted of SMT such as IC, passive component, combined with fired LTCC substrate, We carried out the surface microstructure of sintered electrode and the basic reliability evaluations with sample fired by microwave sintering to solve the problems occurred in post electrode by electric sintering. We evaluated surface densification status of post electrode according to various conditions of microwave sintering. In additions, it is obtained strong effect on blister improvement of post electrode because of over-sintering and the insufficient out gas in bum out process. As a result of adhesion strength, we confirmed $44.3N/mm^2$ in microwave sintering and $34.5N/mm^2$ in electric sintering, respectively. This result will be used for the basic reliability test. Finally, microwave sintering seems to be economic in process time with 30 min compared to electric sintering with 10 hr. In terms of Mass production and efficiency, microwave sintering are excepted to be higher than electric sintering.

• Journal of Powder Materials
• /
• v.17 no.4
• /
• pp.289-294
• /
• 2010

For the aim of low-temperature co-fired ceramic microwave components, sintering behavior and microwave properties (dielectric constant ${\varepsilon}_r$, quality factor Q, and temperature coefficient of resonant frequency ${\tau}_f$) are investigated in $Bi_{18}O(Ca_{0.725}Zn_{0.275})_8Nb_{12}O_{65}$ [BCZN] ceramics with addition of $V_2O_5$. The specimens are prepared by conventional ceramic processing technique. As the main result, it is demonstrated that the additives ($V_2O_5$) show the effect of lowering of sintering temperature and improvement of microwave properties at the optimum additive content. The addition of 0.25 wt% $V_2O_5$ lowers the sintering temperature to $890^{\circ}C$ utilizing liquidphase sintering and show the microwave dielectric properties (dielectric constant ${\varepsilon}_r$ = 75, quality factor $Q{\times}f$ = 572 GHz, temperature coefficient of resonance frequency ${\tau}_f\;=\;-10\;ppm/^{\circ}C$). The estimated microwave dielectric properties with $V_2O_5$ addition (increase of ${\varepsilon}_r$, decrease of $Q{\times}f$, shift of ${\tau}_f$ to negative values) can be explained by the observed microstrucure (sintered density, abnormal grain structure) and possibly high-permittivity $Bi_{18}Zn_8Nb_{12}O_{65}$ (BZN) phase determined by X-ray diffraction.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.121-125
• /
• 2002

이동통신기기 등의 고주파용 LTCC(Low Temperature Co-fired Ceramic) LC filter의 소결결에 있어 기존의 소결공정인 전기로 소결공정과 microwave를 이용한 소결공정을 이용하여 소결하였을때 LC filter의 수축율과 무게감소, 그에 따른 밀도의 변화, SEM을 이용한 표면형상 분석을 통해 급속가열을 통한 공정시간의 단축, 낮은 에너지 소비로 인한 제조단가의 절감, 균일한 가열로 인한 소결온도의 저하 등의 장점을 갖는 microwave sintering을 적용할 수 있는 가능성을 제시하였다.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.3
• /
• pp.390-397
• /
• 2022

The use of microwaves as the energy source for synthesis and sintering of ceramics offers substantial advantages compared to conventional gas-fired and electric resistance furnaces. Benefits include much shorter processing times and reaching the sintering temperature more quickly, resulting in superior final product quality. Most oxide ceramics poorly interact with microwave irradiation at low temperatures; thus, a more complex setup including a susceptor is needed, which makes the whole process very complicated. This investigation pursued a new approach, which enabled us to use microwave irradiation directly in poorly coupled oxides. In many solid-state electrochemical devices, the support is either metal or can be reduced to metal. Metal powders in the support can act as an internal susceptor and heat the entire cell. Then sufficient interaction of microwave irradiation and ceramic material can occur as the sample temperature increases. This microwave heating and exothermic reaction of oxidation of the support can sinter the ceramic very efficiently without any external susceptor. In this study, yttria stabilized zirconia (YSZ) and a Ni-YSZ cermet support were used as an example. The cermet was used as the support, and a YSZ electrolyte was coated and sintered directly using microwave irradiation without the use of any susceptor. The results were compared to a similar cell prepared using a conventional electric furnace. The leakage test and full cell power measurement results revealed a fully leak-free electrolyte. Scanning electron microscopy and density measurements show that microwave sintered samples have lower open porosity in the electrode support than conventional heat treatment. This technique offers an efficient way to directly use microwave irradiation to sinter thin film ceramics without a susceptor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.2
• /
• pp.135-141
• /
• 1995

Abstract The sintering behavior and the electrical properties of sintered PZT ceramics using 2.45 GHz microwave energy were investigated. The ceramics were sintered between $1050 ~ 1130^{\circ}C$ for 5 min. Sintered body with high density and good electrical properties were achieved as the sintering temperature increases. Above $1090^{\circ}C$, however, the bulk density was decreased due to the volatilization of PbO component, and also electrical properties were decreased. The relative dielectric constant, mechanical Quality factor, electro- mechanical coupling factor of microwave sintered body at $1090^{\circ}C$ without PbO atmosphere were 1900, 80, 0.53 respectively, which were comparable to conventional sintering values. The sintering process completed within 20 min using microwave hybrid energy. The processing time and the amount of energy con-sumption could be reduced by microwave hybrid energy assisted rapid sintering.

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.249-254
• /
• 2003

WC-6wt%Co hard metal powders were sintered by a 2.45 GHz multimode microwave applicator in Ar atmosphere. Microwave sintering of WC-6wt%Co powder lowered the sintering temperature and shortened the processing time in less than two hours than by a conventional method. Microstructures of the sintered specimen were studied with scanning electron microscope (SEM) and no abnormal grain growth was observed. Mechanical properties were similar to the values of the specimens sintered by a conventional method. Specimen sintered at 135$0^{\circ}C$ for 30 minutes ,hewed 99%, 20.5 GPa and 8.1 MPa$\sqrt{m}$ of theoretical density, hardness and fracture strength, respectively.