• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.279-287
• /
• 2002

In this paper, a symmetric microwave lens to steer wide angle and to operate at broad band frequency range for a linear phased array transmitter was designed. To get accurate beam steering performance far a linear phased array transmitter, uniform amplitude transmission characteristics of microwave lens was focused. The measured result for the insertion loss deviation between Input and output ports of microstrip lens with 8 beam ports and 8 array ports was $\pm$3.1 ㏈ over 6~18 ㎓ band, which was very uniform characteristics. Using 8 elements linear array antenna, it was confirmed the radiation beam could be steered over $\pm$60$^{\circ}$ in azimuth. And the measured lens performance data and multi-beam steering pattern were presented.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.67-72
• /
• 2001

In this paper, the plano-convex lens antenna fed by a single patch is studied for a microwave remote-traffic monitoring sensor with constraints of small size and low cost. Measurement of an AUT (Antenna Under Test) involves the considerations of a triangular groove for matched layer and metallic shielding effects. A formulation for extracting the parameters of a piano-convex lens antenna, based on geometrical optics, is introduced using Fermat`s principle of the equi-phased ray condition. Teflon ($\varepsilon_{{\gamma}}$/ =2.0) is chosen as a material of a plano-convex lens antenna for adjustment of aberrations on the lens surfaces automatically. A fabricated plano-convex lens shows 3-dB beamwidth of 7.5 degree and side-lobe level of -29 dB with an aperture distribution of the parabolic-squared taper on pedestal. This lens supports easier integration with the planar microwave circuits by using a microstrip single patch as a primary feeder of the lens antenna.feeder of the lens antenna.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.536-540
• /
• 2003

A new concept of adaptive focusing, using a Rotman lens, is presented in this paper. A Rotman lens is a microwave lens which is able to focus microwave power on its focal arc or generate multiple beams. By adding the array of phase shifters between a Rotman lens and antenna elements, the wavefront can be adaptively modulated to focus objects distributed in short range rather than far-field zone. From the optical point of view, the propagations of the lens have been simplified from the Fresnel diffraction integral to the Fourier transform. Using Fourier Transform, a beam propagation method has been developed to show improvement of the resolution by controlling wavefront of wave propagating from an aperture-type antenna array. The beam width(or spot size) and intensity have been calculated for a focused beam propagating from an array having $10{\lambda}$ of its size. For the beam with $20{\lambda},\;30{\lambda}$, and $50{\lambda}$ of geometrical focal length, the half-power beamwidth (spot size) is about $1.1{\lambda},\;1.3{\lambda}$, and $1.9{\lambda}$, respectively.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.11-17
• /
• 2001

In this paper, spherical Luneburg lens antennas have been systematically analyzed using the Eigenfunction Expansion Method (EEM), The developed technique has capability of performing a complete 3-D analysis to characterize the multi-layered dielectric spherical lens with arbitrary permittivity and permeability. This paper describes the analysis technique, and presents the results of the parametric study of Luneburg lens antennas by varying design parameters suoh as the diameter of the lens antenna (up to 80 wavelength), number of spherical shells (up to 30 shells), air-gaps between spherical shells, and dielectric loss of the material. Many representative engineering design curves including the far-field patterns, wide-angle sidelobe characterizations, antenna efficiency have been presented.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.513.2-513
• /
• 2001

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.4
• /
• pp.59-63
• /
• 2008

Purpose: The purpose of this study is to understand a relation of water content measurement with two different method, water removal method and dry method. Methods: 72 hydrogel contact lens containing various water content (ranged from 47% to 58%) were measured by the gravimetric method at 20$^{\circ}C$and 21% of the humidity. We weighed the dried test specimen at room temperature for 30 min after cooling. Results: In dry blotting method, the water content was measured to 47.43${\pm}$8.48%. The water contents was measured to 48.15${\pm}$8.36% with wet blotting condition. It was found that wet blotting method showed the higher water content of about 7% than dry blotting method. In water content with two dry methods, each of results was measured by 47.89${\pm}$8.06% and 49.56${\pm}$7.06%. In case of microwave method, the water content was measured significantly higher water content of about 1.67% than vacuum oven method. However, no statistical difference was found (p>0.05). Conclusions: In water removal method (Dry blotting method and Wet blotting method) to weigh hydrated test specimen, wet blotting method showed significantly higher water content than dry blotting method. Also in case of dry methods (vacuum oven and microwave) to weigh dry test specimen, water content of microwave method showed higher water content than vacuum oven method, but it should be noted that microwave oven method must be used carefully to measure accurateness on the specimen position and wave power.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1121-1127
• /
• 2010

This paper describes the equivalent circuit of $45^{\circ}$ layer, one of $11.25^{\circ}$, $22.5^{\circ}$, and $45^{\circ}$ phase shift layers, which are needed for X-band Radant lens 4-bit phase shifter. The equivalent circuit is extracted by comparing the CST's MWS results with the Agilent's ADS results for $45^{\circ}$ phase shift layer. The simulated result is compared with the measured one. Using the extracted equivalent circuit, the phase bit simulation results of 4-bit Radant lens are also presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1108-1115
• /
• 2004

A new type of a Rotman lens is presented in this paper fur millimeter-wave applications, such as collision avoidance radar. A dielectric slab Rotman lens is proposed to reduce the conductor loss and to create an appropriate farm for favorable implementation at millimeter-wave frequency. The proposed lens consists of a dielectric slab and slot lines whereas the conventional lenses are constructed with parallel conducting plates. The dielectric slab Rotman lens excited in TE$\_$0/ mode shows a high degree of confinement for the fields, low dispersion, and has an appropriate feed structure. A prototype lens has been designed and fabricated with 9 beam ports and 9 array ports together with 9 tapered slot antennas. This lens has been tested in the range from 10 GHz to 15 GHz and the measured beam widths are about 15$^{\circ}$ at 13 GHz. The measurements also show low mutual coupling between beam ports and an efficiency of about 34.6 %. The overall performance is comparable to that of conventional Rotman lenses even though the prototype was tested at lower than desired frequencies in the microwave frequency range due to our limited resources for fabrications and measurements. It is expected that at millimeter-wave frequency the dielectric slab Rotman lens will have lower conductor loss and lower mutual coupling than conventional Rotman lenses.an lenses.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.1-5
• /
• 2010

This paper deals with a method to measure the thickness of scale-layer, iron oxide formed on the surface of the rolling steel, using a dielectric lens antenna. The dielectric lens antenna has an independent characteristic with the frequency in the X-band and changes the spherical wave radiated from a horn antenna into a plane wave at the focusing point. Using this concept, we regard a scale-layer on the rolling steel as a dielectric-PEC(Perfect Electric Conductor) layer and apply a theoretical analysis of the normal-incident plane wave. To reduce the phase error arising from the use of the dielectric lens antenna, this paper utilizes a regression process algorithm. In comparison with the conventional iteration algorithm, the present algorithm led to a unique solution for the thickness of the scale-layer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.45-51
• /
• 2009

The propagation characteristics in parallel plate waveguide with dielectric layer having periodic metal strip pattern are investigated. PIN diode ON/OFF states are regarded as the short and open circuit, respectively, in the simulation using CST's MWS. The $11.25^{\circ}$, $22.5^{\circ}$, and $45^{\circ}$ layers which can be used for X-band 4-bit Radant lens phase shifter, are designed. The simulated results for each dielectric layer are $11.28^{\circ}$, $23.2^{\circ}$, and $46.22^{\circ}$, respectively. Also, the equivalent circuit of each layer at the operating band is realized and simulated using Agilent's ADS. The ADS simulated results are compared with the MWS simulated ones. Measured differential phase shills at the center frequency are $9.6^{\circ}$, $22.4^{\circ}$, and $43^{\circ}$, respectively.