• Geomechanics and Engineering
• /
• v.20 no.3
• /
• pp.233-241
• /
• 2020

Alkali-silica reaction (ASR) is among one of the most important damaging mechanisms in concrete, depending primarily on aggregates which contain reactive minerals. However, expansion in concrete may not directly relate to the reactive minerals. This study aims to investigate the influence of ASR and the expansion of mortar bars depending on aggregate type containing various components such as quartz, clay minerals (montmorillonite and kaolinite) and micas (muscovite and biotite). In this study, the accelerated mortar bar tests (AMBT) were performed in two conditions (mortar bars in the same and sole NaOH solutions). Petrographic thin section studies, X-ray diffraction (XRD) analysis (Rietveld method), scanning electron microscopy (SEM) and chemical analyses were carried out. This study showed that quartzite bars led to increase in expansion values of mortar bars in diabase-1 and andesite when these were in the same NaOH solution. However, three samples (basalt, quartzite and claystone) were found having ASR expansion based on the AMBT when the special molds were used for each sample. SEM study revealed that samples which exhibit highest expansions according to AMBT had a generally rough surface and acicular microstructures in or around the micro-cracks. Basalt and quartzite showed more variable in major oxides than those of other samples based on the chemical analyses, SEM studies and AMBT. This study revealed that the highest expansions were observed to source not only from reactive aggregates but also from alteration products (silicification, chloritization, sericitization and argillisation), phyllosilicates (muscovite, biotite and vermiculite) and clays (montmorillonite and kaolinite).

• Journal of Magnetics
• /
• v.22 no.2
• /
• pp.244-249
• /
• 2017

To get deeper insight into the effect of intergranular additives in sintered Nd-Fe-B magnet and consequently improve the properties better, the interaction between additives (oxide, nitride, and carbide) and Nd-rich phase in the temperature range of 298.15-1400 K was analyzed thermodynamically. It can be found that the oxide additives became less stable than nitrides and carbides. Except for calcium oxide, almost all oxides could react with Nd from Nd-rich phase. To be different from oxide additives, the mechanism of nitrides and carbides was defined with various elements, either reaction with Nd from Nd-rich phase or not. The two different mechanisms would show different effects on the microstructure and hence properties of magnet. The thermodynamic analysis had a better agreement with the experimental information.

• Journal of the Korean Chemical Society
• /
• v.64 no.5
• /
• pp.259-266
• /
• 2020

The main purpose of this study is to examine the different physicochemical properties of spray-dried products. The carrier agents and powders after the spray-drying process were analyzed for encapsulation yield, moisture content, color parameters, total polyphenol content (TPC), antioxidant capacity (AC), bulk density, flowability, wettability, hygroscopicity, water solubility index (WSI), particle size and microstructure. The spray-drying process was carried out with different carrier agents including maltodextrin (MD) and the combination of maltodextrin and gum arabic (MD-GA) with MA/GA ratio of 70/30, dried at the inlet/outlet air temperature of 160 ℃/70 ℃, 4 bar, airflow rate of 70 ㎥·h^-1 and feed flow rate of 750 mL·h^-1. The results showed that the different carrier agents have significant influences on the physicochemical properties of the powder produced by the spray-drying method. In there, while the values of recovery efficiency and flowability of spray-dried products from MD are higher than those of spray-dried products from MD-GA combination, the opposite is true for the values of TPC, AC, bulk density and wettability, whereas hygroscopicity and WSI values are equally represented in both products.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.1-5
• /
• 2014

A low carbon steel, Fe-2.25%Cr steel (ASTM T22), and Fe-2.25%Cr-1.6%W steel (ASTM T23) were aluminized by hot dipping into molten Al baths. After hot-dipping, a thin Al-rich topcoat and a thick alloy layer formed on the surface. The topcoat consisted primarily of a thin Al layer that contained a small amount of Fe, whereas the alloy layer consisted of Al-Fe intermetallics such as $Al_5Fe_2$ and AlFe. Cr, Mo, and W in T22 and T23 steels reduced the thickness of the topcoat and the alloy layer, and flattened the reaction front of the aluminized layer, when compared to the low carbon steel.

• Corrosion Science and Technology
• /
• v.19 no.3
• /
• pp.146-155
• /
• 2020

To elucidate the effect of heat inputs on phase transformation and resistance to intergranular corrosion of F316 austenitic stainless steel (ASS), thermodynamic calculations of each phase and time-temperature-transformation diagram were conducted using JMaPro simulation software, oxalic acid etch test, double-loop electrochemical potentiokinetic reactivation test (DL-EPR), field emission scanning electron microscopy with energy dispersive spectroscopy, and transmission electron microscopy analyses of Cr carbide (Cr₂₃C₆), austenite phase and ferrite phase. F316 ASS containing a relatively low C content of 0.043 wt% showed a slightly sensitized microstructure (acceptably dual structure) due to a small amount of Cr carbide precipitated at heat affected zone irrespective of heat inputs. Based on results of DL-EPR test, although heat input was increased, the ratio of I_r to I_a was only increased very slightly due to a slight sensitization. Therefore, heat inputs have little influences on resistance to intergranular corrosion of F316 austenitic stainless steel containing 0.043 wt% C.

• Journal of Periodontal and Implant Science
• /
• v.37 no.4
• /
• pp.767-777
• /
• 2007

The present study was performed to evaluate the effect of Tetracycline-HCI on the change of implant surface microstructure according to application time. Anodic oxidation surface were utilized. Implant surface was rubbed with 50mg/ml Tetracycline-HCI solution for ${\frac{1}{2}}min.$, 1min., $1{\frac{1}{2}}min.$, 2min., $2{\frac{1}{2}}min.$, and 3min. respectively in the test group. Then, specimens were processed for Ra Value test and scanning electron microscopic observation. The results of this study were as follows. 1. The anodic oxidation surface roughness tests don't show significant difference on conditioning with saline and Tetracycline-HCI. 2. The anodic oxidized surfaces showed the craterous structures. The surface conditioning with Tetracycline-HCI didn't influence on its micro-morphology. In conclusion, Anodic oxidation implant surface is stable to detoxificate with 50mg/ml Tetracycline-HCI of implant surface.

• Journal of Periodontal and Implant Science
• /
• v.37 no.4
• /
• pp.779-789
• /
• 2007

The present study was performed to evaluate the effect of Tetracycline-HCI on the change of implant surface microstructure according to application time. Implant with hydroxyapatite surface was were utilized. Implant surface was rubbed with 50mg/ml Tetracycline-HCI solution and sterilized saline for ${\frac{1}{2}}min.$, 1min., $1{\frac{1}{2}}min.$, 2min., $2{\frac{1}{2}}min.$, and 3min. respectively in the test group. Then, specimens were processed for scanning electron microscopic observation and measured surface roughness by optical interferometer. The results of this study were as follows. 1. Hydroxyapatite surface showed that round particles were deposited irregularly. 2. The roughness of surfaces conditioned with Tetracycline-HCI and saline was lessened and the cracks were increased relative to the application time. In conclusion, the detoxification with 50mg/ml Tetracycline-HCI must be applied respectively with appropriate time according to hydroxyapatite implant surfaces.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2010

Geopolymer materials are attractive as inorganic binders due to their superior mechanical and eco-friendly properties. In the current study, geopolymer-based cement was prepared using aluminosilicate minerals from fly-ash with KOH as an alkaline-activator and $Na_2SiO_3$ as liquid glass. Then, calcium carbonate powder from a clam shell was mixed with the geopolymer and the mixture was coated on a concrete surface to provide points of attachment for environmental organisms to grow on the geopolymers. We investigated the effect of the shell powder grain size on the microstructure and bonding property of the geopolymers. A homogeneous geopolymer layer coated well on the concrete surface via aluminosilicate bonding, but the adhesiveness of the shell powder on the geopolymer cement was dependent on the grain size of the shell powder. Superior adhesive characteristics were shown in the shell powder of large grain size due to the deep penetration into the geopolymer by their large weight. This kind of coating can be applied to the adhesiveness of eco-materials on the surface of seaside or riverside blocks.

• Nuclear Engineering and Technology
• /
• v.40 no.3
• /
• pp.191-198
• /
• 2008

The influence of fission products' contents on the DUPIC fuel powder and pellet properties was experimentally evaluated using SIMFUEL as a surrogate for actual spent PWR fuel due to the high radioactivity of spent fuel. Pure $UO_2$ and SIMFUEL pellets with fission products equivalent to a burn-up of 35,000 MWd/tU and 60,000 MWd/tU were used as impurities in this study. The specific surface area of the powder milled after the OREOX treatment increased and resulted in sintered pellets with a theoretical density (TD) higher than 95%, regardless of the impurity contents. However, the grain size of the sintered pellets decreased with the increasing impurity contents. As a result of the dissolved oxides in $UO_2$ from the impurity groups, the specific surface area of the OREOX powder increased with an increase of the impurities. The grain size of the sintered pellets was significantly decreased by the metallic and oxide precipitates.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.929-940
• /
• 2013

Environmental fatigue of the metallic components in light water reactors has been the subject of extensive research and regulatory interest in Korea and abroad. Especially, it was one of the key domestic issues for the license renewal of operating reactors and licensing of advanced reactors during the early 2000s. To deal with the environmental fatigue issue domestically, a systematic test program has been initiated and is still underway. The materials tested were SA508 Gr.1a low alloy steels, 316LN stainless steels, cast stainless steels, and an Alloy 690 and 52M weld. Through tests and subsequent analysis, the mechanisms of reduced low cycle fatigue life have been investigated for those alloys. In addition, the effects of temperature, dissolved oxygen level, and dissolved hydrogen level on low cycle fatigue behaviors have been investigated. In this paper, the test results and key analysis results are briefly summarized. Finally, an on-going test program for hot-bending of 347 stainless steel is introduced.